Abstract:As a promising cathode material for lithium–sulfur (Li-S) batteries, sulfurized polyacrylonitrile (SPAN) with uniform dispersion of short-chain sulfur moieties on its organic skeletons can effectively avoid lithium polysulfides dissolution and exhibit high specific capacity and long-term cycling stability. However, the practical battery performance of the SPAN cathode is dramatically limited by its relatively poor ionic and electronic accessibility. In this work, a three-dimensional (3D) network of Se0.05S0.95PAN nanofibers incorporated with commercial and low-cost Ketjen black (KB), denoted as 0.05S0.95PAN, is prepared through the electrospinning method. This unique 3D nanofiber structure is beneficial to transport lithium ions and electrons and accommodate volume expansion during lithiation/delithiation processes for Li-S batteries, leading to tremendous improvement of sulfur utilization, rate capability, and long-term cycling performance. 0.05S0.95PAN exhibits an ultrahigh reversible capacity of 1491 mAh g–1 at 0.1C and 1130 mAh g–1 at 5C and retains 1224 mAh g–1 after 500 cycles at 1C, corresponding to a capacity retention of 96.4%. This work proposes a facile strategy for the preparation of sulfur cathodes applicable in lithium–sulfur batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00585.Material preparation, material characterization, electrochemical measurements, SEM images of the ES-PAN fiber and fiber, elemental analysis data table, XPS spectrum of 0.05S0.95PAN, cycling performance of the 0.05S0.95PAN cathode at 0.5C, rate performance of 0.05S0.95PAN at different rates, CV curves of 0.05S0.95PAN and ES-Se0.05S0.95PAN at different rates and linear fit, HR-SEM images and EDS element mappings of 0.05S0.95PAN after cycling, XPS spectrum of the 0.05S0.95PAN cathode after cycling, SEM images of the 0.05S0.95PAN cathode before/after cycling, and comparison of the previous report (PDF)This article has not yet been cited by other publications.

A new insight into capacity fading of sulfurized polyacrylonitrile composite in carbonate electrolyte

Improved Electrochemical Performance And Capacity Fading Mechanism Of Nano-Sized Limn0.9fe0.1po4 Cathode Modified By Polyacene Coating

Porous sulfurized poly(acrylonitrile) nanofiber as a long-life and high-capacity cathode for lithium–sulfur batteries

Sulfurized polyacrylonitrile as cathodes for advanced lithium–sulfur batteries: advances in modification strategies

S0.87Se0.13/CPAN Composites As High Capacity and Stable Cycling Performance Cathode for Lithium Sulfur Battery

Charge/discharge Characteristics of Sulfurized Polyacrylonitrile Composite with Different Sulfur Content in Carbonate Based Electrolyte for Lithium Batteries

Polyisoprene Captured Sulfur Nanocomposite Materials for High-Areal-Capacity Lithium Sulfur Battery

Facile synthesis of sulfurized polyacrylonitrile composite as cathode for high-rate lithium-sulfur batteries

Capacity Fade Analysis of Sulfur Cathodes in Lithium-Sulfur Batteries

Enhanced Cycle Performance of Hollow Polyaniline Sphere/sulfur Composite in Comparison with Pure Sulfur for Lithium–sulfur Batteries

Sulfur Composite Cathode Materials for Rechargeable Lithium Batteries

Dual-shell Hollow Polyaniline/sulfur-Core/polyaniline Composites Improving the Capacity and Cycle Performance of Lithium–sulfur Batteries

One-step synthesis of nano-S/C@PANI composites for lithium-sulfur batteries with high rate and long lifespan

Preparation of PAN-based carbon fiber/Co3O4 composite and potential application in structural lithium-ion battery anodes

In Situ Polymerization of Nanostructured Conductive Polymer on 3D Sulfur/Carbon Nanofiber Composite Network as Cathode for High‐Performance Lithium–Sulfur Batteries

Electrospun Sulfurized Polyacrylonitrile Nanofibers for Long-Term Cycling Stability and High-Rate Lithium–Sulfur Batteries

High-capacity Graphene/sulfur/polyaniline Ternary Composite Cathodes with Stable Cycling Performance

Binder-free Polymer Encapsulated Sulfur–carbon Nanotube Composite Cathodes for High Performance Lithium Batteries

Pre-oxidized and composite strategy greatly boosts performance of polyacrylonitrile/LLZO nanofibers for lithium-metal batteries

Polyaniline-modified Cetyltrimethylammonium Bromide-Graphene Oxide-Sulfur Nanocomposites with Enhanced Performance for Lithium-Sulfur Batteries

Hollow Polyaniline Sphere@Sulfur Composites For Prolonged Cycling Stability Of Lithium-Sulfur Batteries