Abstract:As a promising cathode material for lithium–sulfur (Li-S) batteries, sulfurized polyacrylonitrile (SPAN) with uniform dispersion of short-chain sulfur moieties on its organic skeletons can effectively avoid lithium polysulfides dissolution and exhibit high specific capacity and long-term cycling stability. However, the practical battery performance of the SPAN cathode is dramatically limited by its relatively poor ionic and electronic accessibility. In this work, a three-dimensional (3D) network of Se0.05S0.95PAN nanofibers incorporated with commercial and low-cost Ketjen black (KB), denoted as 0.05S0.95PAN, is prepared through the electrospinning method. This unique 3D nanofiber structure is beneficial to transport lithium ions and electrons and accommodate volume expansion during lithiation/delithiation processes for Li-S batteries, leading to tremendous improvement of sulfur utilization, rate capability, and long-term cycling performance. 0.05S0.95PAN exhibits an ultrahigh reversible capacity of 1491 mAh g–1 at 0.1C and 1130 mAh g–1 at 5C and retains 1224 mAh g–1 after 500 cycles at 1C, corresponding to a capacity retention of 96.4%. This work proposes a facile strategy for the preparation of sulfur cathodes applicable in lithium–sulfur batteries.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00585.Material preparation, material characterization, electrochemical measurements, SEM images of the ES-PAN fiber and fiber, elemental analysis data table, XPS spectrum of 0.05S0.95PAN, cycling performance of the 0.05S0.95PAN cathode at 0.5C, rate performance of 0.05S0.95PAN at different rates, CV curves of 0.05S0.95PAN and ES-Se0.05S0.95PAN at different rates and linear fit, HR-SEM images and EDS element mappings of 0.05S0.95PAN after cycling, XPS spectrum of the 0.05S0.95PAN cathode after cycling, SEM images of the 0.05S0.95PAN cathode before/after cycling, and comparison of the previous report (PDF)This article has not yet been cited by other publications.

S0.87Se0.13/CPAN Composites As High Capacity and Stable Cycling Performance Cathode for Lithium Sulfur Battery

Polyisoprene Captured Sulfur Nanocomposite Materials for High-Areal-Capacity Lithium Sulfur Battery

Bio-derived N-doped Porous Carbon As Sulfur Hosts for High Performance Lithium Sulfur Batteries

One-step synthesis of nano-S/C@PANI composites for lithium-sulfur batteries with high rate and long lifespan

High-capacity Graphene/sulfur/polyaniline Ternary Composite Cathodes with Stable Cycling Performance

Enhanced Cycle Performance of Hollow Polyaniline Sphere/sulfur Composite in Comparison with Pure Sulfur for Lithium–sulfur Batteries

Porous sulfurized poly(acrylonitrile) nanofiber as a long-life and high-capacity cathode for lithium–sulfur batteries

Ternary Sulfur/polyacrylonitrile/mg₀.₆ni₀.₄o Composite Cathodes for High Performance Lithium/sulfur Batteries

An All-Solid-State Sodium–Sulfur Battery Using a Sulfur/Carbonized Polyacrylonitrile Composite Cathode

Polyaniline-modified Cetyltrimethylammonium Bromide-Graphene Oxide-Sulfur Nanocomposites with Enhanced Performance for Lithium-Sulfur Batteries

Facile Synthesis of Porous Li2S@C Composites As Cathode Materials for Lithium–sulfur Batteries

New Scalable Sulfur Cathode Containing Specifically Designed Polysulfide Adsorbing Materials

Solid-State Transformations of Active Materials in the Pores of Sulfurized-Polyacrylonitrile Fiber Membranes via Nucleophilic Reactions for High-Loading and Free-Standing Lithium–Sulfur Battery Cathodes

Li‐Rich Organosulfur Cathode with Boosted Kinetics for High‐Energy Lithium‐Sulfur Batteries

Electrospun Sulfurized Polyacrylonitrile Nanofibers for Long-Term Cycling Stability and High-Rate Lithium–Sulfur Batteries

Sulfur-containing polymer/carbon nanotube composite cathode materials for high-energy lithium–sulfur batteries

Dual-shell Hollow Polyaniline/sulfur-Core/polyaniline Composites Improving the Capacity and Cycle Performance of Lithium–sulfur Batteries

Metallic and Polar Co 9 S 8 Inlaid Carbon Hollow Nanopolyhedra As Efficient Polysulfide Mediator for Lithium−sulfur Batteries

Sulfur Composite Cathode Materials for Rechargeable Lithium Batteries

Rationally Design a Sulfur Cathode with Solid‐Phase Conversion Mechanism for High Cycle‐Stable Li–S Batteries

Interface polymerization synthesis of conductive polymer/graphite oxide@sulfur composites for high-rate lithium-sulfur batteries