[Cephalexin in pulmonary infections in children].

G. Paschetta,V. de Biasi

1971-12-08

Minerva Pediatrica

Abstract:

What problem does this paper attempt to address?

The construction of an efficient magnesium-lithium separation thin film composite membrane with dual aqueous-phase monomers (PIP and MPD)

Xin Cheng,Qiaoming Pan,Huifen Tan,Keke Chen,Wenchao Liu,Yingying Shi,Shengyu Du,Baoku Zhu

DOI: https://doi.org/10.1039/d3ra04258h

IF: 4.036

2023-01-01

RSC Advances

Abstract:A series of thin film composite (TFC) membranes was prepared with piperazine (PIP) and m-phenylenediamine (MPD) in different ratios, and the magnesium-lithium separation performance of TFC membranes in salt-lake brine with the magnesium-lithium ratio of 28 were systematically compared. The prepared TFC membranes exhibited high rejection of magnesium ions and negative rejection of lithium ions with high water flux, enabling high magnesium-lithium separation efficiency. The characterisation using FTIR spectroscopy, XPS, zeta potential measurements, and SEM techniques indicated that the composition and surface morphology of the membrane prepared with dual aqueous monomers were found to be different from those prepared with single aqueous monomers under the similar conditions. The interfacial polymerization process of different monomers and the structure-performance mechanism of TFC membranes were further discussed.
Enhancing Mg 2+ /Li + separation performance of nanofiltration membranes through polyelectrolyte modulation and surface modification

Jingjun Wang,Hao Zhang,Rukang Tian,Huiyan Shen,Wei-Hua Li,Yunkun Wang

DOI: https://doi.org/10.1016/j.memsci.2024.122725

IF: 9.5

2024-04-08

Journal of Membrane Science

Abstract:The increasing demand for lithium resources in the rapidly growing new energy industry has spurred interest in efficient lithium extraction from salt-lakes using Nanofiltration membranes, owing to their impressive ionic rejection capabilities. However, achieving effective Mg 2+ /Li + selective separation remains a critical challenge for the widespread application of NF membranes in lithium extraction. This study focuses on the utilization of poly(dimethyldiallylammonium chloride)-modified polyethersulfone substrate for interfacial polymerization modulation in the preparation of polyamide nanofiltration membrane. The prepared membrane exhibited high MgCl 2 rejection. And then the prepared membrane was subsequently optimized by post-modification with piperazine. Previous and subsequent modifications resulted in smaller pores, narrower pore size distribution, and lower surface negativity of the modified membrane. These properties contributed to the significantly higher MgCl 2 rejection rate of the modified membrane (94.7%) than that of the Control membrane (46.1%). This excellent rejection property ensured the efficient Mg 2+ /Li + separation performance of the modified membrane. It was noteworthy that the Mg 2+ /Li + separation factor for lithium extraction in simulated brine reached an impressive 77.2. In addition, the modified membrane retained a comparable pure water permeance and Na 2 SO 4 rejection rate as the control membrane and showed excellent stability, significantly improving the Mg 2+ /Li + separation efficiency while reducing energy consumption. This study presents a simple strategy to fabricate NF membranes with excellent Mg 2+ /Li + separation factor.

engineering, chemical,polymer science
A Nano‐Heterogeneous Membrane for Efficient Separation of Lithium from High Magnesium/Lithium Ratio Brine

Huawen Peng,Qiang Zhao

DOI: https://doi.org/10.1002/adfm.202009430

IF: 19

2021-01-27

Advanced Functional Materials

Abstract:Lithium extraction from salt lake brines is highly demanded to circumvent the lithium supply shortage. However, polymer nanofiltration membranes suffer from low lithium permeability while nanofluidic devices are hindered by complicated preparation and miniaturized scales despite high permeability. Here, the authors report a facile strategy to prepare positively charged nanofiltration membranes for ultrapermeable and selective separation of lithium ions from concentrated magnesium/lithium mixtures. A new electrolyte monomer (diaminoethimidazole bromide, DAIB) containing bidentate amine groups is designed to modify pristine polyamide composite membranes. Structure characterizations and simulations show that the DAIB modification brings about nano‐heterogeneity that not only improves surface hydrophilicity, but also reduces water transport resistance through the ≈100 nm thick separation layer. Water permeance of the modified membrane improves fivefold and is coupled with good stability in 200‐h continuous nanofiltration. It exhibits high lithium flux (0.7 mol m−2 h−1) for brines (Mg2+/Li+ ratio 20) at 6 bar operation pressure.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,nanoscience & nanotechnology
Improving Mg 2+ /Li + separation performance of polyamide nanofiltration membrane by swelling-embedding-shrinking strategy

Hengyu Li,Yunhao Li,Meng Li,Yan Jin,Guodong Kang,Yiming Cao

DOI: https://doi.org/10.1016/j.memsci.2022.121321

IF: 9.5

2022-12-28

Journal of Membrane Science

Abstract:Extraction of lithium from salt lakes is an important route for lithium sources. Due to the unique structure and separation mechanism, i.e., size exclusion and Donnan effect, Nanofiltration (NF) is considered as a promising way to separate magnesium (Mg 2+ ) and lithium (Li + ) ions. However, the Mg 2+ /Li + separation factor of NF membrane fabricated by traditional interfacial polymerization (IP) is usually dissatisfactory. Here, a swelling-embedding-shrinking strategy was proposed to modify polyethyleneimine (PEI)/trimesoyl chloride (TMC) NF membranes using diethylenetriamine (DETA) to improve the performance in Mg 2+ /Li + separation. The pristine PEI/TMC NF membrane was swollen with methanol to increase the polyamide chain spacing followed by embedding electropositive DETA as a modifier. The charge properties and pore structure of the active layer could be regulated by optimizing the modification conditions. Within comparison to the pristine membrane (TFC-0), the pure water flux of modified NF membrane (TFC-3) increased by 63.6% because of the rougher surface and the larger pore size. Meanwhile, the embedding of electropositive DETA reduced the electronegative property of membrane surface. In consequence, TFC-3 membrane exhibited higher rejection of MgCl 2 (93.9% against 88.4%) and lower rejection of LiCl (31.0% against 32.1%), thus showing a twofold improvement in Mg 2+ /Li + separation factor ( S Li, Mg = 11.38 against 5.87). The swelling-embedding-shrinking strategy in this article provided a good reference for the modification of NF membranes in the separation of multivalent and monovalent ions.

engineering, chemical,polymer science
Nanofiltration membrane with modified nano-gradient structure and positive charge for Li separation from high Mg/Li ratio brine

Peng Zhao,Fei Guo,Lingfeng Wang,Huange Zhen,Ning Zhang,Shaohua Yin,Guoli Zhou,Xuehua Ruan,Gaohong He,Xiaobin Jiang

DOI: https://doi.org/10.1016/j.desal.2024.117394

IF: 11.211

2024-02-01

Desalination

Abstract:Nanofiltration membranes with high selectivity and long-term stability for magnesium and lithium ions are crucial to efficiently enriching lithium resources in salt lake brines. Herein, a nano-gradient-structured nanofiltration membrane was fabricated, in which PEI with different molecular weights and TMC were utilized in a gradient interfacial polymerization process to construct the target active layer. Via this facile strategy, the grafting density of PEI and the amino group introduced were properly adjusted, and the pore size distribution and surface charge of the active layer were optimized. The fabricated active layer simultaneously possesses sub-nanometer pore size with a modified gradient structure and high interfacial positive charges, which can accurately screen lithium and magnesium. The successful grafting of secondary PEI and the high positive charge and continuity of the active layer have been demonstrated. After 150 hour operation (Mg/Li ratio of 50), PEI-70000/PA/PES nanofiltration membrane achieved a lithium‐magnesium separation factor (S Li/Mg ) as high as 150 while maintaining the stable permeation flux of approximately 20 L·m −2 ·h −1 ·MPa −1 , and the terminal Mg/Li ratio on the permeable side falls to 0.32, which exhibits significant potential for extracting Li from salt lake brines with high Mg/Li ratio with promising long-term stability.

engineering, chemical,water resources
Polyamide nanofiltration membranes with rigid–flexible microstructures for high-efficiency Mg 2+ /Li + separation

Yunhao Li,Shuhao Wang,HengYu Li,Dandan Liu,Yan Jin,Guodong Kang,Yiming Cao

DOI: https://doi.org/10.1016/j.seppur.2022.122552

IF: 8.6

2022-11-11

Separation and Purification Technology

Abstract:Lithium extraction from salt-lake brine with a high Mg 2+ /Li + ratio is crucial for mitigating lithium supply shortage. Positively charged polyamide nanofiltration membranes, which are often prepared by performing interfacial polymerization (IP) using polyethyleneimine and trimesoyl chloride, are considered to be promising candidates for Mg 2+ /Li + separation owing to their high energy efficiency and low environmental impact. However, the performance of these membranes is severely hindered by "useless pores" and "defects" present in the flexible polyamide layer. Herein, we provide a facile strategy for modifying flexible semi-aromatic polyamide chains by intercalating a rigid electropositive monomer, histamine, to remold the internal pores and positive charge density at a molecular level. Two routes, namely, "swelling-embedding-reacting-shrinking (SERS)" and "in-situ interposition (SIP)" were used to construct a new polyamide layer with rigid–flexible microstructures. The fabricated SERS-0.50 membrane showed a 5-fold higher water flux and 2-fold increase in the Mg 2+ /Li + separation factor compared with the IP membrane. Moreover, the SIP-0.15 membrane with an enhanced positive charge density exhibited a considerably higher Mg 2+ /Li + separation factor (15.38, 500 % increase compared with that of the IP membrane) for brine with a Mg 2+ /Li + ratio of 20. This study provides a reference for developing nanofiltration membranes used for high-efficiency Mg 2+ /Li + separation.

engineering, chemical
High flux Mg2+/Li+ nanofiltration membranes prepared by surface modification of polyethylenimine thin film composite membranes

Hao Luo,Huawen Peng,Qiang Zhao

DOI: https://doi.org/10.1016/j.apsusc.2021.152161

IF: 6.7

2022-03-01

Applied Surface Science

Abstract:Nanofiltration plays emerging roles in lithium extraction from salt-lake brines with high magnesium-to-lithium (Mg2+/Li+) ratio, yet current lithium extraction nanofiltration membranes show relatively low water permeability. A new monomer (1-(2-hydroxyethyl)-1,3,5,7-tetraazaadamantane-1-ium bromide, HMTAB) was designed to improve membrane separation performances by means of surface modification. Infrared characterizations show that the HMTAB monomer was anchored the pristine polyethylenimine (PEI) thin film composite membrane through esterification condensation. Average roughness of the HMTAB membrane is relatively small (5.7 nm), while the thickness of the top-layer was increased by ∼ 20%, i.e., from 90 to 110 nm. Water flux of the HMTAB membrane in filtrating Mg2+/Li+ mixture (2000 ppm, Mg2+/Li+: 100) at 6 bar pressure is 97.9 L m-2h−1, which is 3.6 times as high as the pristine PEI membrane. Meanwhile, the Mg2+/Li+ ion selectivity of the HMTAB membrane is maintained, and the membrane reduced the high Mg2+/Li+ ratio (50) in the feed to a relatively low value (4.9) in the permeate. Last, the modified membrane exhibits stable performance in 40 h’ continuous nanofiltration.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Positively charged nanofiltration membranes for efficient Mg2+/Li+ separation from high Mg2+/Li+ ratio brine

Guoke Zhao,Yang Zhang,Yu Li,Guoyuan Pan,Yiqun Liu

DOI: https://doi.org/10.1016/j.advmem.2023.100065

2023-01-01

Advanced Membranes

Abstract:Nanofiltration has gained increasing attention in lithium extraction from salt lake brine with high Mg2+/Li+ ratio. However, conventional nanofiltration membranes with negatively charged surfaces suffer from low Mg2+/Li+ selectivity. Herein, positive nanofiltration membranes with high charge density were fabricated via a two-step charge enhancement strategy. High concentration of polyethylenimine was used as the aqueous monomer to ensure the abundant amino groups on the membrane surface. To further enhance the electro-positivity, 2, 3-epoxypropyl trimethyl ammonium chloride was grafted through ring-opening reactions. The as-obtained membranes demonstrated positive zeta potentials over a large pH range (3-10), leading to significantly strengthened Donnan exclusion for Mg2+. The membrane rejection to MgCl2 was up to 99.3% while the rejection to LiCl was only -30%. The Mg2+/Li + separation factor was 167 when filtration simulated brine with a Mg2+/Li+ ratio of 20 (2000 ppm MgCl2 and LiCl mixture), which is the highest value achieved among polyamide-based nanofiltration membranes. In addition, the membranes exhibited good stability in 40 h' continuous testing. The modification strategy proposed in the present work is highly compatible with current industrial membrane preparation processes and easy to scale up with cost effectiveness.
High positively charged composite nanofiltration membranes modified by a novel bis-quaternary ammonium monomer for Li + extraction from high Mg 2+ /Li + ratio salt lakes

Yaru Fan,Hongjing Tian,Kunpeng Wang,Guoli Zhou,Jingtao Wang,Guosheng Li,Yijun Cao,Yingwei Wang,Xiaobin Jiang,Weijie Kou

DOI: https://doi.org/10.1016/j.seppur.2024.130276

IF: 8.6

2024-11-04

Separation and Purification Technology

Abstract:The demand for lithium resources is increasing globally. Salt lakes have been an important source of lithium exploitation. However, Mg 2+ /Li + separation is a challenge mainly for lithium extraction from salt lakes with high Mg 2+ /Li + ratio. In this paper, a novel monomer QTHEED with bis-quaternary ammonium was designed and synthesized. Composite nanofiltration membranes were also prepared by surface modification of polyamide membranes. The permeance (23.08 L m −2 h −1 MPa −1 ) and Li + /Mg 2+ selectivity (21.7) of modified membranes are both ∼3 times higher than those of the pristine membrane. Increased positive charge of membranes enhances the rejection of Mg 2+ . Furthermore, QTHEED modification brings hydrophilic groups, Turing structure, and larger membrane pores. Simulation results confirmed that the incorporation of the QTHEED enabled the membranes to effectively separate Mg 2+ and Li + and to be more conducive to the passage of water molecules. In addition, the nanofiltration performance of the modified membrane was stable after 40 h of continuous nanofiltration tests at 4 bar pressure. This study presented a novel and efficient approach for separating Mg 2+ and Li + in industrial settings.

engineering, chemical
Efficient Lithium Recovery from Water Using Polyamide Thin-Film Nanocomposite (TFN) Membrane Modified with Positively Charged Silica Nanoparticles

Amir Aghaei,Muhammad Amirul Islam,Elham Jashni,Aria Khalili,Jae-Young Cho,Mohtada Sadrzadeh

DOI: https://doi.org/10.1021/acsami.4c15939

2024-11-20

Abstract:The separation of Li+ from Mg2+ in salt-lake brines using nanofiltration (NF) has become the most popular solution to meet the rising demand for lithium, particularly driven by the extensive use of lithium-ion batteries. This study presents the fabrication of a uniquely designed polyamide (PA) thin-film nanocomposite (TFN) membranes with ultrahigh Li+/Mg2+ selectivity and enhanced water flux by covalently incorporating mixed ligands functionalized silica nanoparticles (F-SiO2NPs) into the selective PA layer and covalently bonding them to the membrane surface. In this strategy, bare silica nanoparticles (SiO2NPs) were functionalized with mixed superhydrophilic ligands, including primary amine and quaternary ammonium groups, resulting in a highly positive surface charge primarily from the quaternary ammonium groups and enabling covalent conjugation via amine groups. Among the F-SiO2NP-incorporated membranes, M500 containing 500 ppm of F-SiO2NPs exhibited the best performance. In a solution with 2000 ppm salt concentration (Li+/Mg2+ ratio of 1:20), the M500 membrane showed an improved Li+/Mg2+ selectivity of 7.41 compared to the nonmodified TFC membrane, which had a selectivity of 5.05. Further surface conjugation of the M500 sample with 1500 ppm of F-SiO2NPs resulted in the C1500 membrane, demonstrating the best performance among all of the surface-modified membranes. C1500 showed an outstanding Li+/Mg2+ selectivity of 37.95, with a Mg2+ rejection of 95.7% and a Li+ rejection of -63.2%, and a water flux of 56.0 L m-2 h-1 at 70 psi. Notably, a 7.5-fold improvement in Li+/Mg2+ selectivity over the TFC membrane was achieved without compromising the water flux. This is evident from the nearly identical water flux values of the TFC, M500, and C1500 membranes, which were 57.1, 54.8, and 56.0 L m-2 h-1, respectively. Considering key factors for large-scale applications, such as cost-effectiveness, environmental impact, the abundance of synthetic precursors, and the maturity of synthesis and tailoring technologies, SiO2NP-based modifications outperform all other reported approaches to date.
Quaternary phosphonium-polyamide membranes for efficient lithium extraction from brine sources

Guoke Zhao,Ying Wan,Guoyuan Pan,Hao Yu,Gongqing Tang,Xiaozhi Gong,Yang Zhang,Jie Sun,Yiqun Liu

DOI: https://doi.org/10.1016/j.seppur.2024.127787

IF: 8.6

2024-05-10

Separation and Purification Technology

Abstract:Lithium extraction from brine sources such as salt lakes, seawater, and produced water from oil/gas fields is garnering increasing interests from the academic and industrial sectors due to its cost-effectiveness and reduced environmental impact. A critical technological challenge is the efficient separation of Mg 2+ and Li + ions. Many researchers have reported the preparation of positively charged nanofiltration membranes with quaternary ammonium groups, yet investigations about quaternary phosphonium groups are scarce. In this work, positively charged nanofiltration membranes were prepared utilizing polyethyleneimine as the aqueous phase monomer, trimesoyl chloride as the organic phase monomer, and 3-bromopropyl triphenyl phosphonium bromide as the functionalizing monomer. The TFC-P + membranes, enriched with a high density of quaternary phosphonium groups and an enhanced Donnan effect, achieve a MgCl 2 rejection of 98.9 %, a Mg 2+ /Li + selectivity of 81.6, and a water flux of 50 LMH under 0.5 MPa. The membranes possess an enhanced comprehensive separation capability that exceeds that of the majority of nanofiltration membranes documented in scholarly articles. Additionally, the membranes exhibit outstanding anti-fouling and anti-bacterial characteristics, essential for their industrial applications. The preparation method proposed herein is simple and conducive to continuous production processes. In light of the abundant produced water reserves from oil and gas extraction, future work will focus on pilot-scale lithium extraction experiments.

engineering, chemical
Advanced Mg 2+ /Li + separation nanofiltration membranes fabricated with Girard's reagent T based on functional end-capping strategy

Na Yang,Keting Li,Yufan Hao,Longfei Zhang,Yongli Sun,Luhong Zhang,Bin Jiang

DOI: https://doi.org/10.1016/j.memsci.2024.122483

IF: 9.5

2024-01-26

Journal of Membrane Science

Abstract:Polyethyleneimine (PEI) nanofiltration (NF) membranes hold great application prospects in lithium extraction from salt lakes due to their high positive charge properties. However, the poor permeability of the membranes caused by the dense separation layer structure severely hinders their further application. Herein, a functional end-capping strategy was employed to address this problem by adding the effective end-capping reagent, Girard's Reagent T (GRT), to the PEI aqueous phase as the co-reaction reagent. Under the dual functions of the end-capping effect and the quaternary ammonium groups of GRT, the looseness and positive charge of the membrane were simultaneously optimized. After the modification of GRT, the looser structure of the PEI/GRT NF membrane improved its pure water flux (PWF) to 115 L m −2 h −1 at 6 bar, which was around 3.7 times higher than that of the original PEI NF membrane. Meanwhile, the enhanced positive charge (from −8 to 9 mV, pH = 7) of the membrane bottom surface allowed it to maintain the high rejection rate of MgCl 2 at 97.2 %. Besides, the PEI/GRT NF membrane exhibited good Mg 2+ /Li + selectivity (S Mg 2+ /Li + = 22.7, 2000 ppm, Mg 2+ /Li + mass ratio: 20:1). Therefore, this study provides a simple and feasible strategy for the preparation of high-permeable PEI NF membranes with good Mg 2+ /Li + separation performance.

engineering, chemical,polymer science
Sulfonium-polyamide membranes for high flux Mg2+/Li+ separation

Huawen Peng,Yongjin Hu,Shaoping Li,Jingyi Rao,Qiang Zhao

DOI: https://doi.org/10.1016/j.memsci.2023.121515

IF: 9.5

2023-05-01

Journal of Membrane Science

Abstract:High performance Mg2+/Li+ separation membranes are needed to meet the rising demands for lithium supply, yet state-of-the-art polyamide nanofiltration membranes show limited permeance due to relatively dense structures. This work exploited sulfonium salts for the first time to modify nanofiltration membranes, leading to sulfonium-polyamide membranes with high Mg2+/Li+ separation performance. The occurrence and competition of three types of reactions during the surface modification process were studied and correlated to properties of resultant membranes. Both the positive charge and loose structures of polyamide membranes were enhanced as a result of sulfonium modification, leading to ∼4.3 times improved permeance. The modified membrane exhibited water permeance (∼26.4 L m-2 h-1 bar-1) that is one of the top tier values among recent membranes, coupled with good Mg2+/Li+ selectivity (∼11) in separating high Mg2+/Li+ ratio feed (∼103). Moreover, the modified membrane showed good stability during one-month continuous operation. This work shows the promising potential of sulfoniums for engineering advanced lithium extraction membranes.

engineering, chemical,polymer science
Novel polyamide nanofiltration membrane PEI-(β-CD@g-C 3 N 5 )/TMC based on microfiltration substrate for efficient separation of lithium and magnesium

Wubin Wang,Jin Wang,Yufei Yan

DOI: https://doi.org/10.2139/ssrn.4882858

IF: 11.211

2024-09-19

Desalination

Abstract:With the development of industry, the scarcity of lithium resources is becoming increasingly prominent. Therefore, the development of high-performance nanofiltration (NF) membranes for lithium extraction from salt lakes has become crucial. Herein, β-Cyclodextrin (β-CD) and amino-rich graphitic carbon nitride (g-C 3 N 5 ) sol were uniformly mixed to form β-CD@g-C 3 N 5 , which was then mixed with polyetherimide (PEI) monomer and subjected to interfacial polymerization (IP) reaction with trimesoyl chloride (TMC) on a 0.22 μm microfiltration (MF) membrane to prepare the PEI-(β-CD@g-C 3 N 5 )/TMC composite NF membrane. Through thin plate theory and gradient operation pressure filtration tests, it was found that the composite NF membrane prepared on the MF membrane substrate was not only defect-free but also exhibited superior compression resistance. In Li + /Mg 2+ filtration tests, the PEI-(β-CD@g-C 3 N 5 )/TMC membrane showed superior NF performance, with a Li + /Mg 2+ selectivity coefficient of 38.85 and a permeability of 8.91 L·m −2 ·h −1 ·bar −1 . This was attributed to the effect of β-CD@g-C 3 N 5 , which could thin the separation layer, slightly enlarge and more uniformly distribute the pores, increase hydrophilicity, and enhance positive charge; meanwhile, the cavity structure provided by β-CD helped to effectively separate Li + /Mg 2+ . Furthermore, under conditions of mixed salt solutions with different Mg 2+ /Li + mass ratios and 80 h of continuous filtration, the membrane exhibited excellent stability. This work introduces innovative membrane materials and design concepts to the field of lithium extraction via NF, potentially paving the way for the industrial application of NF technology.

engineering, chemical,water resources
Space‐Confined Synthesis of Thinner Ether‐Functionalized Nanofiltration Membranes with Coffee Ring Structure for Li+/Mg2+ Separation

Wentong Meng,Sifan Chen,Pu Chen,Feng Gao,Jianguo Lu,Yang Hou,Qinggang He,Xiaoli Zhan,Qinghua Zhang

DOI: https://doi.org/10.1002/advs.202404150

IF: 15.1

2024-09-15

Advanced Science

Abstract:The physical structure of the membrane is improved by the introduction the space‐confined layer at the top of the membrane to inhibit the upward diffusion of polyethyleneimine. The membrane exhibits excellent Li+/Mg2+ selectivity as well as Li+ permeability by exploiting the high affinity of the ether chain for Li+ and shows high potential in the extraction of high purity lithium. Positively charged nanofiltration membranes have attracted much attention in the field of lithium extraction from salt lakes due to their excellent ability to separate mono‐ and multi‐valent cations. However, the thicker selective layer and the lower affinity for Li+ result in lower separation efficiency of the membranes. Here, PEI‐P membranes with highly efficient Li+/Mg2+ separation performance are prepared by introducing highly lithophilic 4,7,10‐Trioxygen‐1,13‐tridecanediamine (DCA) on the surface of PEI‐TMC membranes using a post‐modification method. Characterization and experimental results show that the utilization of the DCA‐TMC crosslinked structure as a space‐confined layer to inhibit the diffusion of the monomer not only increases the positive charge density of the membrane but also reduces its thickness by ≈35% and presents a unique coffee‐ring structure, which ensures excellent water permeability and rejection of Mg2+. The ion–dipole interaction of the ether chains with Li+ facilitates Li+ transport and improves the Li+/Mg2+ selectivity (SLi,Mg = 23.3). In a three‐stage nanofiltration process for treating simulated salt lake water, the PEI‐P membrane can reduce the Mg2+/Li+ ratio of the salt lake by 400‐fold and produce Li2CO3 with a purity of more than 99.5%, demonstrating its potential application in lithium extraction from salt lakes.

materials science, multidisciplinary,nanoscience & nanotechnology,chemistry
Prevalence of chronic pain, insomnia, and fatigue in Hong Kong.

R. Fielding,W. Wong

2012-08-01

Abstract:1. Chronic pain, insomnia and fatigue affect a substantial proportion of the Hong Kong general population; as much as a quarter of the adult population experience one of these chronic symptoms. The prevalence of comorbidity is also high, impacting nearly one-third of the adult population. This is a considerable burden to society in terms of individual suffering and disability and to the health care system. 2. Those who are older, female, more educated, married or divorced, or with other health problems are more likely to develop these chronic symptoms.
Fabrication of positively charged nanofiltration membrane with uniform charge distribution by reversed interfacial polymerization for Mg2+/Li+ separation

Yunhao Li,Shuhao Wang,Wenyuan Wu,Haijun Yu,Ruxin Che,Guodong Kang,Yiming Cao

DOI: https://doi.org/10.1016/j.memsci.2022.120809

IF: 9.5

2022-10-05

Journal of Membrane Science

Abstract:Nanofiltration is considered a promising technology for separation of multivalent/monovalent ions such as extracting lithium from Salt Lake brine with high Mg2+/Li+ ratio. However, the nanofiltration membranes fabricated via conventional interfacial polymerization process generally possess negatively charged surface and have low Mg2+/Li+ selectivity. Herein, we proposed a new and facile method, i.e., reversed interfacial polymerization (RIP), to prepare nanofiltration membranes with positively charged surface and uniform charge distribution. The sequence of amine (polyethyleneimine, PEI) and acyl chloride (trimesoyl chloride, TMC) monomers on polysulfone support was reversed compared to the conventional interfacial polymerization (IP) process. Moreover, the solvent of amine monomer was acetone instead of water. The nanofiltration membranes fabricated by this method exhibited higher water flux (from 4.88 to 22.25 Lm−2h−1) and MgCl2 rejection (from 84.36% to 97.71%). Meanwhile, LiCl/MgCl2 separation factor in single salt solution reached up to 13.93, which was almost quadruple compared to the conventional control membrane. In addition, the developed nanofiltration membrane also exhibited an excellent separation selectivity (SLi, Mg = 9.22) in mixture system (Mg2+/Li+ mass ratio of 20), which had good application potential in extracting lithium resources from Salt Lake brine.

engineering, chemical,polymer science
Nanofiltration membrane with crown ether as exclusive Li+ transport channels achieving efficient extraction of lithium from salt lake brine

Hongwei Li,Ying Wang,Tingyu Li,Xiang-Kui Ren,Jixiao Wang,Zhi Wang,Song Zhao

DOI: https://doi.org/10.1016/j.cej.2022.135658

IF: 15.1

2022-06-01

Chemical Engineering Journal

Abstract:Lithium extraction from salt lake brines with high Mg2+/Li+ ratios represents an effective alternative for tackling the scarcity of lithium resources. In this work, nanofiltration (NF) membrane with exclusive Li+ transport channels was designed and prepared through facile interfacial polymerization, in which polyethyleneimine (PEI) bonded with 15-crown-5 ether (15C5) through hydrogen interaction was selected as the aqueous monomer () and reacted with trimesoyl chloride (TMC). The channels generated by 15C5 molecules could facilitate Li+ transport owing to their affinity to Li+. Molecular dynamics simulation was conducted to further confirm the Li+ transport through membrane with exclusive Li+ transport channels provided by 15C5. The membrane displayed a permeability of 8.0 L·m−2·h−1·bar−1 and stable separation factor (SLi,Mg) of 14, which could reduce Mg2+/Li+ mass ratio of a simulated brine from 20 to 1.7. Furthermore, a three-stage NF process was designed and performed using a membrane to separate a simulated salt lake brine, containing multiple ions and Mg2+/Li+ mass ratio of 50. After the treatment, the ultimate permeate solution of the third stage contained 24 ppm of Li+ and 2.7 ppm of Mg2+ with Mg2+/Li+ mass ratio of 0.1. Therefore, this process could be applied to obtain Li2CO3 products with high purity. Our investigation highlights the highly efficient Mg2+/Li+ separation through NF membranes with exclusive Li+ transport channels, potentially applicable to lithium extraction from salt lake brines with high Mg2+/Li+ mass ratios.
Aza-crown ether-coupled polyamide nanofiltration membrane for efficient Li+/Mg2+ separation

Zhiyuan Zha,Tingyu Li,Ismail Hussein,Ying Wang,Song Zhao

DOI: https://doi.org/10.1016/j.memsci.2024.122484

IF: 9.5

2024-03-01

Journal of Membrane Science

Abstract:The scarcity of lithium can be effectively addressed by extracting it from salt-lake brines. In this work, aza-crown ether (diazo-18-crown-6, DA18C6) was coupled into a polyamide (PA) network interfacial polymerized by trimesoyl chloride and polyethyleneimine (PEI) for efficient Li+/Mg2+ separation. The embedment of DA18C6 molecule into PA network was confirmed by structural characterization and density functional theory simulation, which enhanced crosslinking degree and reduced average pore size of PA selective layer. In addition, the strong interaction between DA18C6 and Li+ was proven through molecular dynamics simulation. The resulting PEI@DA18C6-PA membrane displayed a high pure water permeance of 10.4 L⋅m− 2⋅h− 1⋅bar− 1 and an excellent Li+/Mg2+ separation factor (S Li,Mg ) of 11.2, which was comparable with most reported Li+/Mg2+ separation membranes. Furthermore, the PEI@DA18C6-PA membrane was employed in a three-stage NF treatment process to filtrate simulated brines containing a high Mg2+/Li+ ratio of 57. The results demonstrated that Li+ can be effectively concentrated and extracted through the membrane to obtain a permeate with an ultralow Mg2+/Li+ ratio of only 0.03, suggesting that PEI@DA18C6-PA membrane has great application potential in lithium extraction from salt-lake brines.

engineering, chemical,polymer science
Positively-charged PEI/TMC nanofiltration membrane prepared by adding a diamino-silane coupling agent for Li+/Mg2+ separation

Huanhuan Wu,Haoyue Zhao,Yakai Lin,Xin Liu,Lin Wang,Hong Yao,Yuanhui Tang,Lixin Yu,Haihui Wang,Xiaolin Wang

DOI: https://doi.org/10.1016/j.memsci.2023.121468

IF: 9.5

2023-01-01

Journal of Membrane Science

Abstract:Positively charged nanofiltration membrane has gained significant interest in magnesium and lithium separation due to its separation mechanism, especially in salt lake-based lithium industry. To obtain a high-density positive charged surface and high Li+/Mg2+ selectivity, a novel thin-film nanocomposite (TFN) nanofiltration (NF) membrane for recovery of Li+ from Mg/Li mixtures with Mg2+/Li+ ratios of 20 was successfully prepared by using polymeric amine polyethyleneimine (PEI) and monomeric amine silane coupling agent (3-diamino-methylcyclohexyl triethoxysilane, DTES). Then the effect of DTES on the surface properties and performance of the prepared DTES/PEI/TMC TFN membranes were investigated. Chemical composition analysis revealed that DTES not only hydrolyzed to Si-OH and then self-polymerized to Si-O-Si, but also reacted with the self-carrying acyl chloride of 1,3,5-benzene trichloromethane (TMC). Moreover, SiO2 nanoparticles were in-situ generated from DTES inside the PA layer with high compatibility. Due to the compatible properties with the positively charged PEI polymer, the reacted DTES was distributed uniformly in the formed TFN selective layer with no noticeable aggregation. The doping of SiO2 into the polyamide network gave rise to the enlargement of the membrane pore size, enhanced the surface hydrophilicity, and reinforced the surface positive charges. The water flux of the DTES/PEI/TMC membrane improved from 36.9 L m 2 h 1 to 49.58 L m(-2) h(- 1) compared to the PEI/TMC membrane. Additionally, the Mg2+ and Li (+) rejection of the optimized membranes was 91.46% and 10.5%, respectively, with permeability and selectivity (SLi, Mg = 12.95) superior to that of the commercial NF membranes. Considering the commercial availability of DTES, this study not only offers a high-performance nanofiltration membrane for recovering lithium from brines but also provides a feasible strategy for industrial separation of other monovalent and divalent ions.

[Cephalexin in pulmonary infections in children].

The construction of an efficient magnesium-lithium separation thin film composite membrane with dual aqueous-phase monomers (PIP and MPD)

Enhancing Mg 2+ /Li + separation performance of nanofiltration membranes through polyelectrolyte modulation and surface modification

A Nano‐Heterogeneous Membrane for Efficient Separation of Lithium from High Magnesium/Lithium Ratio Brine

Improving Mg 2+ /Li + separation performance of polyamide nanofiltration membrane by swelling-embedding-shrinking strategy

Nanofiltration membrane with modified nano-gradient structure and positive charge for Li separation from high Mg/Li ratio brine

Polyamide nanofiltration membranes with rigid–flexible microstructures for high-efficiency Mg 2+ /Li + separation

High flux Mg2+/Li+ nanofiltration membranes prepared by surface modification of polyethylenimine thin film composite membranes

Positively charged nanofiltration membranes for efficient Mg<SUP>2+</SUP>/Li<SUP>+</SUP> separation from high Mg<SUP>2+</SUP>/Li<SUP>+</SUP> ratio brine

High positively charged composite nanofiltration membranes modified by a novel bis-quaternary ammonium monomer for Li + extraction from high Mg 2+ /Li + ratio salt lakes

Efficient Lithium Recovery from Water Using Polyamide Thin-Film Nanocomposite (TFN) Membrane Modified with Positively Charged Silica Nanoparticles

Quaternary phosphonium-polyamide membranes for efficient lithium extraction from brine sources

Advanced Mg 2+ /Li + separation nanofiltration membranes fabricated with Girard's reagent T based on functional end-capping strategy

Sulfonium-polyamide membranes for high flux Mg2+/Li+ separation

Novel polyamide nanofiltration membrane PEI-(β-CD@g-C 3 N 5 )/TMC based on microfiltration substrate for efficient separation of lithium and magnesium

Space‐Confined Synthesis of Thinner Ether‐Functionalized Nanofiltration Membranes with Coffee Ring Structure for Li+/Mg2+ Separation

Prevalence of chronic pain, insomnia, and fatigue in Hong Kong.

Fabrication of positively charged nanofiltration membrane with uniform charge distribution by reversed interfacial polymerization for Mg2+/Li+ separation

Nanofiltration membrane with crown ether as exclusive Li+ transport channels achieving efficient extraction of lithium from salt lake brine

Aza-crown ether-coupled polyamide nanofiltration membrane for efficient Li+/Mg2+ separation

Positively-charged PEI/TMC nanofiltration membrane prepared by adding a diamino-silane coupling agent for Li<SUP>+</SUP>/Mg<SUP>2+</SUP> separation