Synthesis and antiproliferative activity of monocationic arylthiophene derivatives.

M. Ismail,M. Youssef,Reem K. Arafa,S. Al-Shihry,W. El-Sayed

DOI: https://doi.org/10.1016/j.ejmech.2016.12.007

IF: 7.088

2017-01-27

European Journal of Medicinal Chemistry

Abstract:

What problem does this paper attempt to address?

Influence of various implanting angles of micro-implants on peak stress in peri-implant surface

dan lihua,dong fusheng,gong weiwei,zhang xiong

DOI: https://doi.org/10.3321/j.issn:1673-8225.2008.52.005

2008-01-01

Abstract:BACKGROUND:Skeletal anchorage with mini-implants has greatly broadened the treatment possibilities in orthodontics over the last few years.To reduce implant failure rates,it is advisable to obtain adequate stress distribution around implant.OBJECTIVE:To evaluate the stress distribution on bone adjacent to a mini-implant under the different implanting direction and angle.MATERIALS:Jaw data were obtained from the scanning of Dong.Implant model was established according to screwed mini-implant,titanium,Aarhus Screw Syst 1.6,Medicon,Germany.METHODS:Three-dimensional finite element mandible model was established based on the CT scanning data.The mini-implant was implanted in the region between first mola and second premolar at 30°,60° and 90° tilted mesiolly,and 30° and 60° tilted occlusally,respectively.In addition,a force load of 1.96 N was applied horizontally to the head of implant.MAIN OUTCOME MEASURES:The maximum first(pulling) and third(pressing) stress,minimum stress,Von-mises stress and maximum strain were calculated.RESULTS:The peak pulling and pressing stress and Von-mises stress at 30° tilted mesiolly were significantly smaller than the other models.The Von-mises stress mainly located at the neck of implant-bone interface,and decreased rapidly in the lamina cortex.The Von-mises stress in cancellous bone was small,and the side adjacent to loading was pressed,while the other side was pulled.CONCLUSION:Implanting angle shows much more influence on the stress distribution.The stress is primarily located at the neck of implant under different loads.Decreased implanting angle and reduced angle between load line and implant long axis can reduce peak stress.
A biomechanical investigation of miniscrews placed on a mandible for temporary anchorage; a patient-specific finite element analysis

Samet Ciklacandir,Gokcenur Gokce Kara,Yalcin Isler

DOI: https://doi.org/10.1080/10255842.2024.2365909

IF: 1.6

2024-06-24

Computer Methods in Biomechanics & Biomedical Engineering

Abstract:Miniscrews are temporary skeletal anchorage devices that are widely used in orthodontic treatment, and their success depends on the placement area, angle, technique, and screw dimensions. This study aimed to investigate the effects of miniscrew lengths, insertion angles, and force directions on a mandible model consisting of teeth, cortical and cancellous bones. One Dental Volumetric Tomography (DVT) scan from a patient who had miniscrews were used for mandibular bone modeling to perform finite element analysis. The model variables included miniscrew lengths (6, 8, and 10 mm), insertion angles (−15°, 45°, 60°, and 90°), and force directions (30°, 45°, and 60°). The minimum and maximum stresses were calculated as 18.61 and 37.11 MPa at 6 mm and 10 mm, respectively. According to the insertion angles, the lowest stress was observed at 60°, while the highest stress was found at 15° in the ventral direction. At force directions, the lowest stress was at 60°, and the highest stress was at 45°. However, there were no significant differences in insertion angles and force directions. A statistically significant difference was determined in miniscrew length. As a result, the best result was calculated to be 6 mm inserted at a 60° angle, which could induce the lowest stress. Increasing the miniscrew length will increase the stress on the mandible. In addition, because of the higher force direction, stress decreases with shorter power arms.

engineering, biomedical,computer science, interdisciplinary applications
[Stress Distribution in Press-Fit Orthodontic Microimplant Bone Interface].

Jian-chao Wu,Ji-na Huang,Shi-fang Zhao,Xue-jun Xu

DOI: https://doi.org/10.3969/j.issn.1006-7248.2006.06.014

2006-01-01

Abstract:PURPOSE:The goal of this study is to analyse the stress distribution in the press-fit microimplant-bone interface and its indications for immediate loading of orthodontic microimplant.METHODS:Three-dimensional finite element models were created of a 20 mm section of posterior mandible simplified in isosceles trapezoid shape, 30 mm in height, 10mm in upper side width, 14 mm in lower side width,with a single microimplant, 1.2 mm in diameter, 6 mm in length embedded in the bone. The cortical bone thickness was assumed as 1.6 mm. Cortical and cancellous bone were modeled as transversely isotropic and linearly elastic materials. Titanium was modeled as isotropic and linearly elastic material. Perfect bonding was assumed at microimplant- bone interfaces. ANSYS 9.0 finite element analysis software was used to generate the simplified finite element models of the local mandible-implant complex. 0 mm, 0.05 mm and 0.1 mm press-fit were arbitrarily set to the implant-bone interface to mimic the situation of immediate placement of microimplant. Stresses in the microimplant-bone interface were calculated under these "press-fit".RESULTS:Stresses distributed mainly in the cortical bone interface. At Omm press-fit, the stress was 0 MPa. For 0.05mm press-fit, the stress was 1648 MPa in mesio-distal direction, 1782MPa in occluso-gingival direction;and for 0.1 mm, it reached 2012MPa in mesio-distal direction, 2110MPa in occluso-gingival direction. As the "press-fit" increased, the stresses increased accordingly.CONCLUSION:Values of initial stress in the microimplant-bone interface due to press-fit generated by immediately placed microimplant were very high in these limited and simplified three dimensional finite element models. It reminded us that the initial stress be taken into consideration when immediate loading of the microimplant is planned. Supported by Research Fund of Health Bureau of Zhejiang Province (2005B104).
[The Effect of Mini-Implant Lengths on Stress Distributions in Peri-Implant Surface].

Li-hua Shan,Fu-sheng Dong,Wei-wei Gong,Xiong Zhang

DOI: https://doi.org/10.3969/j.issn.1000-1182.2011.01.007

2011-01-01

Abstract:OBJECTIVE:To observe the effect of mini-implant lengths on stress distribution in peri-implant surface.METHODS:The 3D finite element analysis mandible and mini-implant models with diameter of 1.6 mm, lengths of 6, 8, 10 and 12 mm were established. The mini-implants were inserted into designed site of mandibular vertically, respectively. A force of 1.96 N were applied mesioly and 45 degrees tilted mesio-vertically in models. The stress distribution under every condition was recorded and analyzed.RESULTS:When load was applied mesially, the maximum stress varied from 3.500 to 3.765 MPa, the maximum displacement varied from 1.266 to 1.288 microm. When load was applied 45 degrees tilted mesio-vertically, the maximum stress varied from 4.075 to 4.510 MPa, the maximum displacement varied from 1.668 to 1.694 microm. All of the maximum stress and displacement of loading mesially were lower than loading mesio-vertically.CONCLUSION:The change of the mini-implant length within 6-12 mm don't show much influence on the stress distribution. The loading type is an important factor influencing stress and displacement of peri-implant bone.
A 3D finite element analysis of biomechanical effects on teeth and bone during true intrusion of anteriors using miniscrews

Ankit Bharadwaj,Sachin Ahuja,Japjee Uppal,Eenal Bhambri,Renu Sewta,Seema Gupta

DOI: https://doi.org/10.1016/j.ortho.2024.100925

2024-10-10

Abstract:Purpose: The primary objective of this study was to investigate the biomechanical effects and stresses on bone, periodontal ligament (PDL), cementum and displacement along X-, Y- and Z-axis during true intrusion of incisors using mini-implants with Finite Element Analysis; the secondary objective of the study was to find out the best method for anterior intrusion in clinical practice to treat anterior deep bite malocclusions. Materials and methods: A 3D finite element method was used to simulate true anterior intrusion with sliding mechanics using mini-implants. Two groups were modelled with mini-implants placed distal to lateral incisors for Model 1, and below the anterior nasal spine (ANS) for Model 2, to achieve intrusion. von Mises stress, principal stress on PDL and alveolar bone, displacements in all 3 planes were determined. Results: Amongst the modalities compared in the present study, the stresses on bone and PDL were showing best behavior for mini-implants placed distal to lateral incisors (Model 1). The teeth showed controlled tooth movement in Model 1. Conclusion: Maximum stress was found in the cortical bone and in the PDL. Nature of the stress changed from compressive to tensile from cervical area to root apex, concentrating mainly at the apical area. Amongst the modalities compared, the best controlled tooth movements for anterior intrusion to treat anterior deep bite malocclusions, was for mini-implants placed distal to lateral incisors (Model 1).
Influence of sagittal root positions on the stress distribution around custom-made root-analogue implants: a three-dimensional finite element analysis

Chunping Lin,Hongcheng Hu,Junxin Zhu,Yuwei Wu,Qiguo Rong,Zhihui Tang

DOI: https://doi.org/10.1186/s12903-021-01809-4

2021-09-14

BMC Oral Health

Abstract:Abstract Background Stress concentration may cause bone resorption even lead to the failure of implantation. This study was designed to investigate whether a certain sagittal root position could cause stress concentration around maxillary anterior custom-made root-analogue implants via three-dimensional finite element analysis. Methods The von Mises stresses in the bone around implants in different groups were compared by finite element analysis. Six models were constructed and divided into two groups through Geomagic Studio 2012 software. The smooth group included models of unthreaded custom-made implants in Class I, II or III sagittal root positions. The threaded group included models of reverse buttress-threaded implants in the three positions. The von Mises stress distributions and the range of the stresses under vertical and oblique loads of 100 N were analyzed through ANSYS 16.0 software. Results Stress concentrations around the labial lamella area were more prominent in the Class I position than in the Class II and Class III positions under oblique loading. Under vertical loading, the most obvious stress concentration areas were the labial lamella and palatal apical areas in the Class I and Class III positions, respectively. Stress was relatively distributed in the labial and palatal lamellae in the Class II position. The maximum von Mises stresses in the bone around the custom-made root-analogue implants in this study were lower than around traditional implants reported in the literature. The maximum von Mises stresses in this study were all less than 25 MPa in cortical bone and less than 6 MPa in cancellous bone. Additionally, compared to the smooth group, the threaded group showed lower von Mises stress concentration in the bone around the implants. Conclusions The sagittal root position affected the von Mises stress distribution around custom-made root-analogue implants. There was no certain sagittal root position that could cause excessive stress concentration around the custom-made root-analogue implants. Among the three sagittal root positions, the Class II position would be the most appropriate site for custom-made root-analogue implants.

dentistry, oral surgery & medicine
Effects of exposure length, cortical and trabecular bone contact areas on primary stability of infrazygomatic crest mini-screws at different insertion angles

Bingran Du,Yuan Lin,Mohan Ji,Qiaohua Yang,Jiang Jiang,Fei Wang,Xiaoyi Wang,Jinchuan Tan,Rui Jia,Jianyi Li

DOI: https://doi.org/10.1186/s12903-024-04626-7

2024-08-09

BMC Oral Health

Abstract:Background: The infrazygomatic crest mini-screw has been widely used, but the biomechanical performance of mini-screws at different insertion angles is still uncertain. The aim of this study was to analyse the primary stability of infrazygomatic crest mini-screws at different angles and to explore the effects of the exposure length (EL), screw-cortical bone contact area (SCA), and screw-trabecular bone contact area (STA) on this primary stability. Methods: Ninety synthetic bones were assigned to nine groups to insert mini-screws at the cross-combined angles in the occlusogingival and mesiodistal directions. SCA, STA, EL, and lateral pull-out strength (LPS) were measured, and their relationships were analysed. Twelve mini-screws were then inserted at the optimal and poor angulations into the maxillae from six fresh cadaver heads, and the same biomechanical metrics were measured for validation. Results: In the synthetic-bone test, the LPS, SCA, STA, and EL had significant correlations with the angle in the occlusogingival direction (rLPS = 0.886, rSCA = -0.946, rSTA = 0.911, and rEL= -0.731; all P < 0.001). In the cadaver-validation test, significant differences were noted in the LPS (P = 0.011), SCA (P = 0.020), STA (P = 0.004), and EL (P = 0.001) between the poor and optimal angulations in the occlusogingival direction. The STA had positive correlations with LPS (rs = 0.245 [synthetic-bone test] and r = 0.720 [cadaver-validation test]; both P < 0.05). Conclusions: The primary stability of the infrazygomatic crest mini-screw was correlated with occlusogingival angulations. The STA significantly affected the primary stability of the infrazygomatic crest mini-screw, but the SCA and EL did not.
Evaluation of stress and displacement of maxillary canine during the single canine retraction in the maxillary first premolar extraction cases- A finite element study

Wenbo Zhao,Yu Lou,Weijun Yan

DOI: https://doi.org/10.1007/s00784-024-05590-w

2024-03-09

Abstract:Objectives: This finite element study aimed to simulate maxillary canine movement during anterior teeth retraction. Materials and methods: Three methods of maxillary canine movement including miniscrew sliding with high hooks (MSH), miniscrew sliding with low hooks (MSL), and the traditional sliding method (TS) without using miniscrews were simulated using three-dimensional finite element analysis. The initial displacement of the maxillary canine, the maximum principal stress of the periodontal ligament and the Von Mises stress were calculated. Results: The distolingual tipping movements of the canine were shown in three movement modes. MSH showed a small tendency to lingual tipping movement and a extrusion movement while MSL had the largest lingual inclination. TS demonstrated a tendency toward distolingual torsion displacement. Compressive stress values were mainly concentrated in the range - 0.003 to -0.006 MPa. For tensile stress, the distribution of MSH and MSL was concentrated in the range 0.005 to 0.009 MPa, TS was mainly distributed about 0.003 MPa. Von Mises equivalent stress distribution showed no significant difference. Conclusions: The loss of tooth torque was inevitable, irrespective of which method was used to close the extraction space. However, miniscrew application and higher hooks reduced the loss of torque and avoided lingual rotation. Clinical relevance: This study shows that miniscrew implants with different hooks can better control the movement of the maxillary canines. The non-invasive nature of the finite element analysis and its good simulation of dental stress and instantaneous motion trend have a clinical advantage in the analysis of tooth movement.
Evaluation of stress patterns on maxillary posterior segment when intruded with mini implant anchorage: A three-dimensional finite element study

Nikhita Pekhale,Amit Maheshwari,Mukesh Kumar,Veerendra V. Kerudi,Harshal Patil,Bhushan Patil

DOI: https://doi.org/10.4103/2321-1407.173726

2016-01-11

APOS Trends in Orthodontics

Abstract:Introduction The aim of this study is to evaluate stress and displacement effects of maxillary posterior intrusion mechanics with mini-implant anchorage by using finite element method. Materials and Methods A computer stimulation of three-dimensional model maxilla with all teeth, PDL, bone, mini-implants, brackets, arch wire, force element, and transpalatal arch was constructed on the basis of average anatomic morphology. Finite element analysis was done to evaluate the amount of stress and its distribution during orthodontic intrusive force. Results Increased Von Mises stress values were observed in mesio-cervical region of first molar. The middle third of second premolar and second molar and regions adjacent to force application sites also showed relatively high stress values. Minimum stress values were observed in apical region of first premolar as it is away from force application. Conclusion Using three mini-implant and transpalatal arches, this study demonstrates that significant amount of true intrusion of maxillary molars could be obtained with lesser concentration of stresses in the apical area recorded.
[Selected diagnostic problems in rheumatology].

I. Zimmermann-Górska

Abstract:
[Three-Dimensional Finite Element Analysis of Influence of Occlusal Surface Height on Stress Distribution Around Posterior Implant-Supported Single Crown].

Xu Zhao,Lei Zhang,Jian Sun,Zhen-yu Yang,Qiu-fei Xie

DOI: https://doi.org/10.3969/j.issn.1671-167x.2016.01.017

2016-01-01

Abstract:OBJECTIVE:To evaluate the effect of the occlusal surface height of a mandibular posterior implant-supported single crown on stress in bone tissues.METHODS:Three-dimensional finite element models of the implant-supported single crown replacing the missing right lower second premolar, mesial and distal natural teeth, periodontal membrane, alveolar bone, loaded rigid body and analog food of almond were established. Using the Federation Dentaire International (FDI) system, the first premolar, the second premolar and the first molar were represented with 44, 45, 46. Three occlusal surface heights of the crown were studied: (1) normal height; (2) 15 μm reduction in height; (3) 30 μm reduction in height. The models were loaded by independent loading with maximal occlusal force(44 by 280 N, 45 by 360 N, and 46 by 480 N) and average occlusal force(44 by 140 N, 45 by 180 N, and 46 by 240 N)on the single crown; combined loading (maximal occlusal force transformed into uniform load of 3.7 MPa on top of rigid body, in contact with points on the occlusal surface), and analog almond-like food loading (average occlusal force transformed into uniform load of 1.67 MPa in simulated food chewing, in contact with points on the occlusal surface).RESULTS:For maximal biting force under independent loading, Von Mises stress peak values in bone tissues around 44, 45, and 46 were 82.57 MPa, 45.26 MPa and 27.79 MPa; For average biting force, peak values were 41.28 MPa, 22.63 MPa and 13.89 MPa. Under combined loading, compared with the normal occlusal surface height group, Von Mises stress peak values decreased 4.6 MPa, by 0.84%; increased 7.52 MPa, by 20.04%, and decreased 1.8 MPa, by 5.84%, for 45, 46, and 44 in the 30 μm infra-occlusion group, respectively. Under food loading, Von Mises stress peak values decreased 0.34 MPa, by 1.62%; increased 1.11 MPa, by 2.66%; and increased 0.06 MPa, by 0.54%, and for 45, 46, and 44 in the 30 μm infra-occlusion group, respectively.CONCLUSION:Within the limitation of this study, within 30 μm reduction of the occlusal surface height of implant-supported single crown, no significant difference of the peak values was observed.
Effect of Angled Abutments in the Posterior Maxillary Region on Tilted Implants: a 3D Finite Element Analysis.

Peng Chen,Jianguo Zhang,Juan Yao,Fengling Hu,Liang Song,Youcheng Yu

DOI: https://doi.org/10.1007/s11517-024-03081-4

2024-01-01

Medical & Biological Engineering & Computing

Abstract:The aim of this study was to evaluate the bone tissue effects under dynamic loading using finite element analysis (FEA) for four angled abutments with different deviated palatal lateral tilt angles. A three-dimensional model of the posterior maxillary region and an implant crown model were reconstructed and assembled with a three-dimensional model of the implant, angled abutment, and central screw to create a total of 10 three-dimensional finite element models tilted at 15 ∘ , 20 ∘ , 25 ∘ , and 30 ∘ in three groups, and the dynamic loads simulating oral mastication were loaded on the implant crown to analyze the equivalent stresses and strains in the peri-implant bone tissues. Under the dynamic loading, the cortical bone on the buccal side of the implant neck showed different degrees of stress concentration, and the cortical bone stress was much higher than the cancellous bone, and the strain concentration area of each model was located in the bone tissue around the implant neck and base. For the use of angular abutment, under the premise that the cortical bone stresses and strains of the 10 models meet the requirements for use, the peak stresses of 2.907 MPa, 3.018 MPa, and 2.164 MPa were achieved by using the 20 ∘ angular abutment to achieve the tilt angles of 20 ∘ , 25 ∘ , and 30 ∘ implantation, which is more advantageous compared with other models.
Chronic Ulceration and Sinus Formation due to Foreign Body

Karin Hansen,F. Gottrup

DOI: https://doi.org/10.1177/1534734614550687

2015-12-01

Abstract:Foreign bodies like residues of suture or mesh may lead to a foreign body reaction, cavity formation and continuous secretion and perhaps ulceration. We present a more than 9 years long medical record of a 49 year old man after a simple surgical procedure. The background was a sinus formation generated from a foreign body reaction. The case report shows that this condition is often overlooked and even using advanced equipment, it is difficult to diagnose. The only solution is to diagnose and remove the triggering cause. Fistulography and ultrasound scanning seem to be the optimal diagnostic tool in these cases. The knowledge of the foreign body reaction in tissue continuously needs to be reestablished in the health care system especially in areas, where implantation of foreign material is used.
Single-dose half-body irradiation for the palliation of multiple bone metastases from solid tumors: a preliminary report.

O. Salazar,P. Rubin,F. Hendrickson,C. Poulter,G. Zagars,M. Feldman,S. Asbell,L. Doss

DOI: https://doi.org/10.1016/0360-3016(81)90472-7

1981-06-01

Abstract:
Effects of diameters of implant and abutment screw on stress distribution within dental implant and alveolar bone: A three-dimensional finite element analysis

Yen-Wen Shen,Heng-Li Huang,Jui-Ting Hsu,Lih-Jyh Fuh

DOI: https://doi.org/10.1016/j.jds.2023.12.020

IF: 3.719

2024-01-01

Journal of Dental Sciences

Abstract:Background/purpose: Few studies have investigated the effects of abutment screw diameter in the stress of dental implants and alveolar bones under occlusal forces. In this study, we investigated how variations in implant diameter, abutment screw diameter, and bone condition affect stresses in the abutment screw, implant, and surrounding bone.Materials and methods: Three-dimensional finite element (FE) models were fabricated for dental implants with external hex-type abutments measuring 4 and 5 mm in diameter. The models also included abutment screws measuring 2.0 and 2.5 mm in diameter. Each implant model was integrated with the mandibular bone comprising the cortical bone and four types of cancellous bone. In total, 12 finite element models were generated, subjected to three different occlusal forces, and analyzed using FE software to investigate the stress distribution of dental implant and alveolar bone.Results: Wider implants demonstrated lower stresses in implant and bone compared with standard-diameter implants. The quality of cancellous bone has a minimal impact on the stress values of the implant, abutment screw, and cortical bone. Regardless of occlusal arrangement or quality of cancellous bone, a consistent pattern emerged: larger abutment screw diameters led to increased stress levels on the screws, while the stress levels in both cortical and cancellous bone showed comparatively minor fluctuations.Conclusion: Wider implants tend to have better stress distribution than standard-diameter implants. The potential advantage of augmenting the abutment screw diameter is unfavorable. It may result in elevated stresses in the implant system.

dentistry, oral surgery & medicine
Finite element analysis of the stress state produced by an orthodontic skeletal anchorage system based on miniscrews

Andrea Ancillao,Ugo Andreaus

DOI: https://doi.org/10.4103/2278-9588.113586

2013-01-01

Abstract:Aims: The aim of this work is to produce detailed analysis and quantitative results of the stress state induced in an inferior first molar tooth by an orthodontic mesialization system based on a mini-screw, a bracket, and a rubber elastic string. Materials and Methods: The implant was modeled as a non-osteointegrated Ti-6Al-4V standard mini-screw, implanted in the anterior-buccal region of human jaw. 3D realistic models were constructed using data based on micro-computed tomography scans of human teeth as found in the literature. A couple of self-balanced forces of 4 N was applied and finite element method analysis was run and produced an approximate solution, which allowed to display stress distribution over the whole model. Materials' behavior was assumed elastic and linear. This approximation applies to the 1 st stage of the orthodontic treatments. Results: A detailed qualitative and quantitative analysis of the stress state is presented through images. Results in terms of stresses and displacements were studied to exclude any possibility of bracket debonding, bone failure, and loss of stability of the screw. Results were compared to the ultimate strengths of the bio-materials involved using engineering failure criteria. The actual stress state was found to be lower than the critical values. Conclusion: Results allows to qualitatively see the amount of bone, surronding the mini-screw, and the tooth, that undergoes stress. Furthermore, quantitative analysis of stress could exclude failure in alveolar bone and detachment at the enamel-bracket interface. The applied force and devices were proved to be safe to use for this kind of orthodontic facilities.
Effect of short implant crown-to-implant ratio on stress distribution in anisotropic bone with different osseointegration rates

Xi Yuan,Yuchen Liu,Yunhe Yang,Mingfa Ren,Lailong Luo,Lang Zheng,Yang Liu

DOI: https://doi.org/10.1186/s12903-023-03379-z

2023-09-20

BMC Oral Health

Abstract:Objective: This study aimed to provide evidence for the clinical application of single short implants by establishing an anisotropic, three-dimensional (3D) finite element mandible model and simulating the effect of crown-to-implant ratio (CIR) on biomechanics around short implants with different osseointegration rates. Methods: Assuming that the bone is transversely isotropic by finite element method, we created four distinct models of implants for the mandibular first molar. Subsequently, axial and oblique forces were applied to the occlusal surface of these models. Ultimately, the Abaqus 2020 software was employed to compute various mechanical parameters, including the maximum von Mises stress, tensile stress, compressive stress, shear stress, displacement, and strains in the peri-implant bone tissue. Results: Upon establishing consistent osseointegration rates, the distribution of stress exhibited similarities across models with varying CIRs when subjected to vertical loads. However, when exposed to inclined loads, the maximum von Mises stress within the cortical bone escalated as the CIR heightened. Among both loading scenarios, notable escalation in the maximum von Mises stress occurred in the model featuring a CIR of 2.5 and an osseointegration rate of 25%. Conversely, other models displayed comparable strength. Notably, stress and strain values uniformly increased with augmented osseointegration across all models. Furthermore, an increase in osseointegration rate correlated with reduced maximum displacement for both cortical bone and implants. Conclusions: After fixing osseointegration rates, the stress around shorter implants increased as the CIR increased under inclined loads. Thus, the effect of lateral forces should be considered when selecting shorter implants. Moreover, an implant failure risk was present in cases with a CIR ≥ 2.5 and low osseointegration rates. Additionally, the higher the osseointegration rate, the more readily the implant can achieve robust stability.
Thread shape, cortical bone thickness, and magnitude and distribution of stress caused by the loading of orthodontic miniscrews: finite element analysis

Takuma Sakamaki,Keiichiro Watanabe,Akihiko Iwasa,Toru Deguchi,Shinya Horiuchi,Eiji Tanaka

DOI: https://doi.org/10.1038/s41598-022-16662-w

IF: 4.6

2022-07-23

Scientific Reports

Abstract:Cortical bone thickness is assumed to be a major factor regulating miniscrew stability. We investigated stress distribution in two miniscrews with different thread shapes (type A and B) and in cortical bone of three different thicknesses using three-dimensional (3D) finite element (FE) models. More specifically, 3D FE models of two different miniscrews were created and placed obliquely or vertically into a cylindrical bone model representing different cortical bone thicknesses. When force was applied to the miniscrew, the stress distribution on the screw surface and in the peri-implant bone was assessed using FE methodology. Miniscrew safety was evaluated using a modified Soderberg safety factor. Screw head displacement increased with a decrease in cortical bone thickness, irrespective of screw type. The smallest minimum principal stresses on the screw surfaces remained constant in type A miniscrews on changes in cortical bone thickness. Minimum principal stresses also appeared on the cortical bone surface. Lower absolute values of minimum principal stresses were seen in type A miniscrews when placed vertically and with upward traction in obliquely placed type B miniscrews. Both miniscrews had acceptable safety factor values. Taken together, orthodontists should select and use the suitable miniscrew for each patient in consideration of bone properties.

multidisciplinary sciences
Thyroid cancer: A review of treatment and follow-up

L. Vini,C. Harmer,V. McCready

DOI: https://doi.org/10.1007/BF03165047

1996-02-01

Annals of Nuclear Medicine

Abstract:
Effect of Implant-Abutment Connection and Abutment Angulations on Peri-implant Stress Levels: A Finite Element Analysis Study

Ishtiyak Khatib,Nilesh V Joshi,Prajakta Rao,Mridula Joshi,Anupa Shetty,Vinayak Thorat,Prakash Talreja

Abstract:Introduction: Placement of an implant in the maxillary anterior region is challenging due to the angulation of bone in this area. Angled abutments may be used to achieve proper restorative contours. The present study was undertaken to examine and compare the stress levels of implants in the maxillary anterior region having different types of internal connections and different abutment angulations. Material and methods: Implants with three types of abutment connections, internal conical, Morse taper, and internal hex, were modeled using SolidWorks software. Three abutment angulations of 0, 15, and 30 degrees were used for each type of implant. A 100 N axial load was applied to the implants, and the stresses on the implant, abutment, and bone were analyzed by finite element analysis. Results: Among the straight abutments, the most stress was in model 3A (62.60 MPa). The stress value among angled abutments was highest with 30-degree angled abutments. The value was highest in model 3C (94.83 MPa). Internal hex connection showed the highest stress levels in all degrees of angulation of the abutment, and Morse taper connection showed the least amount of stress in all three abutment angles. The most stress concentration was seen in the cortical bone on the buccal surface in the implant-abutment junction. Conclusion: The Morse taper design of implant exhibited the least-highest stress levels on the alveolar bone. The stress levels increased with the increasing angulation of the implant or implant-abutment connection.

Synthesis and antiproliferative activity of monocationic arylthiophene derivatives.

Influence of various implanting angles of micro-implants on peak stress in peri-implant surface

A biomechanical investigation of miniscrews placed on a mandible for temporary anchorage; a patient-specific finite element analysis

[Stress Distribution in Press-Fit Orthodontic Microimplant Bone Interface].

[The Effect of Mini-Implant Lengths on Stress Distributions in Peri-Implant Surface].

A 3D finite element analysis of biomechanical effects on teeth and bone during true intrusion of anteriors using miniscrews

Influence of sagittal root positions on the stress distribution around custom-made root-analogue implants: a three-dimensional finite element analysis

Effects of exposure length, cortical and trabecular bone contact areas on primary stability of infrazygomatic crest mini-screws at different insertion angles

Evaluation of stress and displacement of maxillary canine during the single canine retraction in the maxillary first premolar extraction cases- A finite element study

Evaluation of stress patterns on maxillary posterior segment when intruded with mini implant anchorage: A three-dimensional finite element study

[Selected diagnostic problems in rheumatology].

[Three-Dimensional Finite Element Analysis of Influence of Occlusal Surface Height on Stress Distribution Around Posterior Implant-Supported Single Crown].

Effect of Angled Abutments in the Posterior Maxillary Region on Tilted Implants: a 3D Finite Element Analysis.

Chronic Ulceration and Sinus Formation due to Foreign Body

Single-dose half-body irradiation for the palliation of multiple bone metastases from solid tumors: a preliminary report.

Effects of diameters of implant and abutment screw on stress distribution within dental implant and alveolar bone: A three-dimensional finite element analysis

Finite element analysis of the stress state produced by an orthodontic skeletal anchorage system based on miniscrews

Effect of short implant crown-to-implant ratio on stress distribution in anisotropic bone with different osseointegration rates

Thread shape, cortical bone thickness, and magnitude and distribution of stress caused by the loading of orthodontic miniscrews: finite element analysis

Thyroid cancer: A review of treatment and follow-up

Effect of Implant-Abutment Connection and Abutment Angulations on Peri-implant Stress Levels: A Finite Element Analysis Study