Abstract:SnO2 has the advantages of excellent photostability and can be prepared at low-temperature below 200 degrees C.It is regarded as one of the excellent materials for the electron transport layer, and widely used in efficient andstable planar heterojunction perovskite solar cells. In this work, the low-cost, dense and uniform SnO2 electrontransport layer is prepared by spin coating at low temperature (150 degrees C) for perovskite solar cells with astructure of FTO/SnO2/CH3NH3PbI3 (MAPbI3)/Spiro-OMeTAD/Au. The crystallization and photoelectricproperties of SnO2 electron transport layers prepared at different concentrations (2.5%-10%) at 150 degrees C, and theinfluences of SnO2 electron transport layers on the formation of perovskite films and the performances ofperovskite solar cells are discussed. By analyzing the scanning electron microscope (SEM), ultraviolet-visiblelight absorption spectrum (UV-Vis) and transmission spectrum of the SnO2 film, it is found that the coverageand light transmittance of the substrate and band gap of the SnO2 film increase as the SnO2 content increases,while the absorbance decreases. By analyzing the SEM, UV-Vis, X-ray diffraction (XRD) and steady-statephotoluminescence spectrum (PL) analysis of the SnO2/MAPbI3 thin film, it is found that the MAPbI3deposited on the SnO2 layer with a concentration of 7.5% is uniform and pinhole-free, has the largest particlesize and the best crystallinity, as well as more effective charge extraction capability and transport capability.By analyzing the electrochemical impedance (EIS) and external quantum efficiency (EQE) of the device, theSnO2 electron transport layer with a concentration of 7.5% has better interface contact and lower interfaceresistance, which is beneficial to reducing the recombination of carriers and improving the photoelectricconversion capability, The perovskite solar cells based on SnO2 layer prepared with a concentration of 7.5%reaches a photoelectric conversion efficiency of 15.82% (Voc = 1.06 V, Jsc = 21.62 mA/cm2, FF = 69.40%), Afterstoring for 600 h in ambient air ((25 +/- 5) degrees C, RH>70%) without encapsulation, its efficiency remains 92% of theinitial efficiency. At the same time, we prepare flexible devices on flexible substrates (TIO/PEN) by using SnO2precursor with a concentration of 7.5%, which exhibits good photovoltaic performance and achieves aphotoelectric conversion efficiency of 13.12%, and storage time for 84 d in ambient air ((30 +/- 5) degrees C, RH>70%)without encapsulation, its efficiency remains 48% of the initial efficiency. The PCE retains 78% of the initialefficiency after 1000 bending cycles with a bending radius of 3 mm. The study of optimizing the concentrationof SnO2 has laid a foundation for improving the performance of flexible perovskite solar cells.

Atomic layer deposition of SnO2 using hydrogen peroxide improves the efficiency and stability of perovskite solar cells

Enhanced efficiency and stability of perovskite solar cells with ultra-thin Al2O3 contact interlayer via low temperature atomic layer deposition

Tin Oxide Bilayer as Effective Electron Transport Layers for Efficient and Stable Perovskite Solar Modules

Electrochemical Reduction and Ion Injection of Annealing‐Free SnO2 for High Performance Perovskite Solar Cells

Unveiling and Overcoming Instabilities in Perovskite Solar Cells Induced by Atomic‐Layer‐Deposition Tin Oxide

Low-temperature Preparation of SnO<sub>2</sub> Electron Transport Layer for Perovskite Solar Cells

Low-Temperature Atomic Layer Deposition of Metal Oxide Layers for Perovskite Solar Cells with High Efficiency and Stability under Harsh Environmental Conditions

Practical and Thermal Atomic Layer Deposition of NiO as Hole‐Transporting Layers for Inverted Perovskite Solar Cells

Poly(vinylpyrrolidone)-doped SnO2 as an electron transport layer for perovskite solar cells with improved performance

Low-temperature preparation of SnO2 electron transportlayer for perovskite solar cells

Toward Commercial-Scale Perovskite Solar Cells: The Role of ALD-SnO 2 Buffer Layers in Performance and Stability

Low Damage Scalable Pulsed Laser Deposition of SnO2 for p–i–n Perovskite Solar Cells

Novel Bilayer SnO2 Electron Transport Layers with Atomic Layer Deposition for High-Performance α-FAPbI3 Perovskite Solar Cells.

Constructing tin oxides Interfacial Layer with Gradient Compositions for Efficient Perovskite/Silicon Tandem Solar Cells with Efficiency Exceeding 28%

Polyelectrolyte-Doped SnO<sub>2</sub> as a Tunable Electron Transport Layer for High-Efficiency and Stable Perovskite Solar Cells

All‐SnO2‐Based Conformal Electron Transport Layer for Efficient Perovskite Solar Cells

Defect engineering of oxygen vacancies in SnOx electron transporting layer for perovskite solar cells

Solvent engineering of SnO2 electron transport layer for high-performance perovskite solar cells

Advanced Applications of Atomic Layer Deposition in Perovskite‐Based Solar Cells

Tailoring the alkalinity of SnO2 colloidal suspension for high‐performance and stable perovskite solar cells

Improved Efficiency and Stability of Organic Solar Cells by Interface Modification Using Atomic Layer Deposition of Ultrathin Aluminum Oxide