Abstract:Methanol is a competitive low-carbon fuel for spark ignition engines. Though it has higher knock resistance than gasoline fuel, knocking combustion is still an obstacle for the application of methanol in spark ignition engines with relatively higher compression ratios. In this work, experimental investigations into knocking combustion and suppression were conducted on a single-cylinder, naturally aspirated, SI engine with a compression ratio of 15. Firstly, the knocking characteristics of the methanol engine with stoichiometric mixture under port fuel injection mode were evaluated. Results showed that knocking combustion occurred under medium and high loads. Especially, under the condition of indicated mean effective pressure (IMEP) = 0.7 MPa, some random heavy knock cycles with ultra-high knock intensity were observed. The frequency of heavy knock was 2.5% and the highest maximum amplitude of pressure oscillations reached 2.39 MPa. This heavy knock was similar to the super-knock phenomenon in boosted direct injection gasoline engines, and it can not be eliminated by retarding spark timing or adopting fuel-lean combustion. Then, the mechanism of the heavy knock was studied by thermodynamic condition analysis. Results showed that the heavy knock was triggered by pre-ignition which was induced by some hot spots in the combustion chamber. Finally, to make the best use of the charge cooling effect, the methanol direct injection strategy was applied to suppress the knocking combustion. When the engine worked with full opening throttle and adopt a single injection, the maximum knock intensity decreased to 0.43 MPa×°CA at −350 °CA ATDC start of injection which was 5.1% of the maximum value during port fuel injection mode. With the co-optimization of the start of injection and spark timing, the engine with a stoichiometric mixture could operate within the knock intensity limit at full load. Under this operating condition, the crank angle of 50% mass fraction burned located at 12 °CA ATDC and IMEP = 1.05 MPa was achieved. What’s more, adopting the optimal split injection instead of a single injection, the knock intensity was further reduced by 14.3% with a slight reduction of 0.02 MPa in IMEP.

Numerical comparative study on knocking combustion of high compression ratio spark ignition engine fueled with methanol, ethanol and methane based on detailed chemical kinetics

The knock study of high compression ratio SI engine fueled with methanol in combination with different EGR rates

Study of Knock in A High Compression Ratio Spark-Ignition Methanol Engine by Multi-Dimensional Simulation

Numerical Comparative Study on Performance and Emissions Characteristics Fueled with Methanol, Ethanol and Methane in High Compression Spark Ignition Engine

Numerical analysis on knock for a high compression ratio spark-ignition methanol engine

Numerical Analysis of Knock Combustion with Methanol-Isooctane Blends in Downsized SI Engine

Comparison of Kinetic Mechanisms for Numerical Simulation of Methanol Combustion in DICI Heavy-Duty Engine

Numerical Analysis of Knock During HCCI in a High Compression Ratio Methanol Engine Based on LES with Detailed Chemical Kinetics

Experimental study of knock combustion and direct injection on knock suppression in a high compression ratio methanol engine

Experimental and Numerical Investigation on Knock for a Heavy-Duty Spark Ignition Methanol Engine

Study of knock in a high compression ratio SI methanol engine using les with detailed chemical kinetics

The Knock Study of Methanol Fuel Based on Multi-Dimensional Simulation Analysis

Numerical Study on Auto-Ignition Characteristics of Hydrogen-Enriched Methane under Engine-Relevant Conditions

Study of Ignition in a High Compression Ratio SI (spark Ignition) Methanol Engine Using LES (large Eddy Simulation) with Detailed Chemical Kinetics

Analysis of Knocking Combustion with Methanol/iso-Octane and Ethanol/iso-Octane Blends in a Spark-Ignition Engine

Comparative study on combustion and emission characteristics of methanol/hydrogen, ethanol/hydrogen and methane/hydrogen blends in high compression ratio SI engine

Experimental study on combustion and emission characteristics of ethanol-gasoline blends in a high compression ratio SI engine

Optical Diagnostics and Chemical Kinetic Analysis on Partially Premixed Combustion Characteristics Fueled with Methanol and Various Cetane Improvers

Numerical Analysis on Original Emissions for a Spark Ignition Methanol Engine Based on Detailed Chemical Kinetics

Cylinder-to-cylinder Variation of Knock and Effects of Mixture Formation on Knock Tendency for a Heavy-Duty Spark Ignition Methanol Engine

Experimental Study on the Characteristics of Knock under DI-HCCI Combustion Mode with Ethanol/Gasoline Mixed Fuel