Abstract:Methanol is a competitive low-carbon fuel for spark ignition engines. Though it has higher knock resistance than gasoline fuel, knocking combustion is still an obstacle for the application of methanol in spark ignition engines with relatively higher compression ratios. In this work, experimental investigations into knocking combustion and suppression were conducted on a single-cylinder, naturally aspirated, SI engine with a compression ratio of 15. Firstly, the knocking characteristics of the methanol engine with stoichiometric mixture under port fuel injection mode were evaluated. Results showed that knocking combustion occurred under medium and high loads. Especially, under the condition of indicated mean effective pressure (IMEP) = 0.7 MPa, some random heavy knock cycles with ultra-high knock intensity were observed. The frequency of heavy knock was 2.5% and the highest maximum amplitude of pressure oscillations reached 2.39 MPa. This heavy knock was similar to the super-knock phenomenon in boosted direct injection gasoline engines, and it can not be eliminated by retarding spark timing or adopting fuel-lean combustion. Then, the mechanism of the heavy knock was studied by thermodynamic condition analysis. Results showed that the heavy knock was triggered by pre-ignition which was induced by some hot spots in the combustion chamber. Finally, to make the best use of the charge cooling effect, the methanol direct injection strategy was applied to suppress the knocking combustion. When the engine worked with full opening throttle and adopt a single injection, the maximum knock intensity decreased to 0.43 MPa×°CA at −350 °CA ATDC start of injection which was 5.1% of the maximum value during port fuel injection mode. With the co-optimization of the start of injection and spark timing, the engine with a stoichiometric mixture could operate within the knock intensity limit at full load. Under this operating condition, the crank angle of 50% mass fraction burned located at 12 °CA ATDC and IMEP = 1.05 MPa was achieved. What’s more, adopting the optimal split injection instead of a single injection, the knock intensity was further reduced by 14.3% with a slight reduction of 0.02 MPa in IMEP.

Analysis of Knocking Combustion with Methanol/iso-Octane and Ethanol/iso-Octane Blends in a Spark-Ignition Engine

Numerical Analysis of Knock Combustion with Methanol-Isooctane Blends in Downsized SI Engine

On Knocking Combustion Development of Oxygenated Gasoline Fuels in a Cooperative Fuel Research Engine

Numerical comparative study on knocking combustion of high compression ratio spark ignition engine fueled with methanol, ethanol and methane based on detailed chemical kinetics

The knock study of high compression ratio SI engine fueled with methanol in combination with different EGR rates

Study on the Effects of Ethanol-gasoline Octane Number on Anti-knock Performance in Direct-injection Gasoline Engine

Experimental study of knock combustion and direct injection on knock suppression in a high compression ratio methanol engine

Effect of fuel properties on knocking combustion in an optical rapid compression machine

Experimental Study on the Characteristics of Knock under DI-HCCI Combustion Mode with Ethanol/Gasoline Mixed Fuel

Auto-ignition and knocking characteristics of gasoline/ethanol blends in confined space with turbulence

Cylinder-to-cylinder Variation of Knock and Effects of Mixture Formation on Knock Tendency for a Heavy-Duty Spark Ignition Methanol Engine

Study of Knock in A High Compression Ratio Spark-Ignition Methanol Engine by Multi-Dimensional Simulation

Study on Combustion Characteristics of a DI Diesel Engine Operating on Diesel/Methanol Blends

Experimental and Numerical Investigation on Knock for a Heavy-Duty Spark Ignition Methanol Engine

Numerical analysis on knock for a high compression ratio spark-ignition methanol engine

The Effect of Acetone-Butanol-ethanol and Gasoline Blends on the Knocking Performance of Spark-Ignition Engine

Splash Blended Ethanol in a Spark Ignition Engine – Effect of RON, Octane Sensitivity and Charge Cooling

The Influence of Mixing Ratio of Low Carbon Mixed Alcohols on Knock Combustion of Spark Ignition Engines

The Knock Study of Methanol Fuel Based on Multi-Dimensional Simulation Analysis

Knock analysis of bio-butanol in TISI engine based on chemical reaction kinetics

Analysis of auto-ignition characteristics of low-alcohol/iso-octane blends using combined chemical kinetics mechanisms