Abstract:Material removal rates as well as surface and subsurface quality are key aspects for the industrial application of ultrashort pulse (USP) laser machining. However, revealing so-called subsurface damage (SSD) is challenging. The presented study visualizes and quantifies subsurface damage patterns in areal USP laser ablation of fused silica (FS) and glass N-BK7 (BK). For the first time, using high-resolution optical coherence tomography (OCT) as non-destructive and three-dimensional (3D) evaluation method, SSD morphologies of areal laser machining induced damages are analysed. Influences of laser wavelength, beam geometry and processed material are investigated. Discovered differences of damage morphologies and depth in FS and BK point out the relevance of selecting suitable process parameters. Based on the evaluation of volumetric OCT data, the authors were able to quantify damage morphologies using the surface texture ratio as well as power spectral density functions. One important finding for the quantification and comparability of damage depths in USP laser processing is the influence of applicable evaluation thresholds. In comparison to area thresholds of 0.001% being applicable to OCT measurements, more lenient thresholds of e.g. 1% commonly applied in destructive SSD measurement methods in average result in a reduction of measured damage depths by a factor of ~ 2. This potentially leads to an underestimation of damage depths depending on methods on thresholds used. The presented measurement and evaluation methods as well as gained process insights are important assets for the future optimization of low-damage USP laser micromachining of brittle materials. Moreover, the general applicability and relevance of OCT-based morphological damage analysis in laser material processing is shown.

Percussion drilling in glasses and process dynamics with femtosecond laser GHz-bursts

Femtosecond Laser Percussion Drilling of Silicon Using Repetitive Single Pulse, MHz-, and GHz-Burst Regimes

Ultrafast and precision drilling of glass by selective absorption of fiber-laser pulse into femtosecond-laser-induced filament

Laser Micro-Hole Drilling of Soda-Lime Glass with Femtosecond Pulses

Simultaneous Multi-Microhole Drilling of Soda-Lime Glass by Water-Assisted Ablation with Femtosecond Laser Pulses.

Femtosecond pulsed laser micro-machining of glass substrates with application to microfluidic devices

Bessel Beam Femtosecond Laser Interaction with Fused Silica Before and After Chemical Etching: Comparison of Single Pulse, MHz-Burst, and GHz-Burst

Hole Drilling of Silica Glass with Infrared Femtosecond Laser Pulses

Water-assisted Drilling of Microfluidic Chambers Inside Silica Glass with Femtosecond Laser Pulses

Mechanisms of damage formation in glass in the process of femtosecond laser drilling

Three-Dimensional Microdrilling of Glass by Multiphoton Process and Chemical Etching

High-quality Rapid Laser Drilling of Transparent Hard Materials

Dynamics of pressure waves during femtosecond laser processing of glass

Revealing Subsurface Damage Morphology and Patterns in areal Ultrashort Pulse Laser Machining of Glass

Femtosecond laser microfabrication of micro-optic elements in glass

Molecular dynamics-guided quality improvement in the femtosecond laser percussion drilling of microholes using a two-stage pulse energy process

Percussion Drilling of Deep Holes Using Picosecond Ultrashort Pulse Laser in Ni-Based Superalloy Coated with Ceramic Thermal Barrier Coatings

Targeted Microforming of Borosilicate Glass Induced by a Laser‐Ablation‐Free Process Using Femtosecond Pulses

Microstructures Induced by Femtosecond Laser Pulses Inside Glasses

Ultrafast Laser Drilling of Crack-free, Debris-free and Heat Affected Zone (Haz)-Free Blind Holes in Al2O3 with Flat Bottom and Reduced Taper Angles

Laser-induced stress by multi-beam femtosecond pulses in fused silica