Abstract:Waterjet-assisted laser drilling technology facilitates the fabrication of high-quality micro-holes by utilizing the collaborative benefits of waterjets and lasers. In this study, the coaxial waterjet-assisted laser drilling (CWALD) technique was employed to improve the properties of micro-holes during femtosecond laser drilling. Based on computational fluid dynamics (CFD) simulations, the stability of the waterjet was initially verified by optimizing the structure of the watercourse and nozzle shape in the CWALD device. Furthermore, a comparative experiment between laser direct drilling (LDD) and CWALD revealed that while CWALD can produce well-rounded micro-holes with a high aspect ratio, it exhibits lower efficiency and results in a larger heat-affected zone (HAZ). To address these drawbacks associated with CWALD, a two-step coaxial waterjet-assisted composite laser drilling (TS-CWALD) method was proposed. TS-CWALD involves applying CWALD for secondary modification of micro-hole shape following LDD with punching. This modification process is pivotal for enhancing drilling accuracy but requires consideration of multiple parameters. For this purpose, regression models were established for the inlet diameter, outlet diameter, and taper; response surface methodology was then employed to optimize these parameters. Subsequently, interactive effects analysis was conducted on different responses based on laser pulse energy, frequency, modification speed, and number of modification cycles. The adequacy of the developed models was subsequently verified using analysis of variance methods. Finally, the successful fabrication of a film hole with an inlet diameter of 205 μm and an outlet diameter of 200 μm, featuring a taper of only 0.2°, was achieved ultimately through meticulous parameter optimization. Furthermore, the micro-hole retained a minimal HAZ. The optimized parameters encompassed a pulse energy of 20.6 μJ, frequency of 127 kHz, modification speed of 3 mm/s, and shape modification carried out over 335 cycles.

Ultrafast Laser Drilling of Crack-free, Debris-free and Heat Affected Zone (Haz)-Free Blind Holes in Al2O3 with Flat Bottom and Reduced Taper Angles

High-quality Rapid Laser Drilling of Transparent Hard Materials

Polarization-dependent, Beam Reflection-Regulated Hole Shaping Dynamics Visualized by In-Situ Imaging of Ultrafast Laser Drilling Process

Laser drilling of micro-holes with controllable taper using 355 nm nanosecond laser

Laser Micro-Hole Drilling of Soda-Lime Glass with Femtosecond Pulses

Experimental investigation and optimization of modification during coaxial waterjet-assisted femtosecond laser drilling

Femtosecond laser processing of controlled tapered micro-holes based on dynamic control of relative attitude

An investigation on the hole quality during picosecond laser helical drilling of stainless steel 304

Percussion Drilling of Deep Holes Using Picosecond Ultrashort Pulse Laser in Ni-Based Superalloy Coated with Ceramic Thermal Barrier Coatings

Investigation on Thermal Barrier Coating Damages for Ultrafast Laser Drilling of Cooling Holes

Triple Rings Trepanning Technology for Holes Ablated Using Nanosecond Pulse Laser in Al2O3 Ceramics Substrate

Hole Drilling of Silica Glass with Infrared Femtosecond Laser Pulses

Development of a Quantitative Method for the Characterization of Hole Quality During Laser Trepan Drilling of High-Temperature Alloy

Super-efficient drilling of metals with ultrafast non diffractive laser beams

Optimizing Hole Shape and Improving Surface Quality of Inconel 718 Alloy by High-Temperature Chemical Assisted Laser Processing

Laser Percussion Drilling of High Temperature Alloy and Qualitative/Quantitative Characterization

Simultaneous Multi-Microhole Drilling of Soda-Lime Glass by Water-Assisted Ablation with Femtosecond Laser Pulses

Femtosecond Laser Drilling of Cylindrical Holes for Carbon Fiber-Reinforced Polymer (CFRP) Composites

Hole Quality and Thermal Defects in Drilled CFRP by Nanosecond Pulsed Laser

Molecular dynamics-guided quality improvement in the femtosecond laser percussion drilling of microholes using a two-stage pulse energy process

Femtosecond laser high-quality drilling of film cooling holes in nickel-based single superalloy for turbine blades with a two-step helical drilling method