Relationship between testosterone and erectile dysfunction.

J. Rajfer

Abstract:Although erectile function is clearly androgen dependent, is it just as clear at what level of testosterone erectile dysfunction (ED) begins? Does the decline in testosterone that occurs with aging always produce ED? Are exogenous androgens the answer to ED? The answers range from clear to complex.

What problem does this paper attempt to address?

Mullerian adenosarcoma of the uterus associated with long-term oral contraceptive use.

W. Tjalma,C. Michener

DOI: https://doi.org/10.1016/J.EJOGRB.2004.07.001

2005-04-01

Abstract:
In situ evaluation of contact stiffness in a slip interface with different roughness conditions using ultrasound reflectometry

S Fukagai,M Watson,H P Brunskill,A K Hunter,M B Marshall,R Lewis

DOI: https://doi.org/10.1098/rspa.2021.0442

Abstract:Understanding the dynamic condition of the interface between a railway wheel and rail is important to reduce the risks and consider the effectiveness of countermeasures for tribological problems. Traditionally the difficulty in obtaining accurate non-destructive interfacial measurements has hindered systematic experimental investigations. Recently, an ultrasound reflectometry technique has been developed as a direct observation method of a rolling-sliding interface; however, the topography dependence under the high contact pressures in a wheel-rail contact has not been clarified. For this reason, a novel in situ measurement of the contact stiffness using ultrasound reflectometry was carried out for three different levels of roughness. A contact pressure equivalent to that in a wheel-rail interface was achieved by using a high-pressure torsion test approach. The dynamic change of contact stiffness with slip was measured using ultrasound and the influence of roughness was investigated. The measured changes were validated using a newly developed numerical simulation, and mechanisms to explain the observed behaviour were proposed in terms of fracture and plastic deformation of the asperity bonds. These findings could help in understanding the traction characteristics for different roughness conditions and also assist in understanding damage mechanisms better, such as wear and rolling contact fatigue.
Wear monitoring of bearing steel using electrostatic and acoustic emission techniques

Jun Sun,R.J.K. Wood,L. Wang,I. Care,H.E.G. Powrie

DOI: https://doi.org/10.1016/j.wear.2005.02.021

IF: 4.695

2005-07-01

Wear

Abstract:Both acoustic emission (AE) and electrostatic (ES) wear monitoring are emerging as useful real-time condition monitoring techniques. These techniques are believed to be sensitive to different aspects of the physics of contact and surface degradation prior to the onset of severe wear. Thus, if both systems are used to monitor tribo-contacts, the physics of early contact degradation could be elucidated and the potential of the systems to detect precursors to severe wear could be investigated. This paper uses AE and ES charge signals generated by a bearing steel contact under dry sliding conditions to monitor the various phases of delamination wear. Tests were undertaken using an instrumented pin-on-disc (PoD) tribometer, which enabled continuous measurement of friction, surface temperature, linear wear, AE and ES signals. The AE and ES results were found to correlate with friction levels and wear rates. From the friction level, three distinct regions were identified and the wear mechanisms within each region were found (by SEM and EDS analysis) to be running-in, delamination/oxidation and oxidation.

engineering, mechanical,materials science, multidisciplinary
Application Study of Acoustic Reflectivity Based on Phased Array Ultrasonics in Evaluating Lubricating Oil Film Thickness

Fei Shang,Huilin Chen,Bo Sun,Shaofeng Wang,Yongquan Han,Wenjing Liu,Fengchun Miao,Zhendong Liu

DOI: https://doi.org/10.3390/coatings14101265

IF: 3.236

2024-10-03

Coatings

Abstract:Bearings play a key role in rolling mills, and the uniformity of their lubricant film directly affects the degree of wear of bearings and the safety of equipment. Due to long-term stress, the lubricant film inside the bearing is not uniformly distributed, resulting in uneven wear between the journal and the shaft tile, which increases the potential safety hazards in production. Traditional disassembly inspection methods are complex and time-consuming. Ultrasonic nondestructive testing technology, which has the advantages of nondestructive and adaptable, has become an effective means of assessing the thickness of the oil film in bearings. In this study, an experimental platform for calibrating the lubricant film thickness in bearings was constructed for the first time, and the acoustic characteristics of different thicknesses of the oil film were measured using ultrasonic detection equipment to verify the accuracy of the simulation process. The experimental results show that after discrete Fourier transform processing, the main features of the frequency channels of the reflected acoustic signals of different thicknesses of the oil film are consistent with the finite element simulation results, and the errors of the oil film thicknesses calculated from the reflection coefficients are within 10% of the set thicknesses, and the measurement ranges cover from 5 μm to 250 μm. Therefore, the above method can realize the accurate measurement of the thicknesses of the oil film in bearings.

materials science, multidisciplinary,physics, applied, coatings & films
Research of real contact area through acoustic microscope

Zhi Gao,Zongze Wu,LinQing Zheng

1994-01-01

Abstract:The acoustic microscope and some other subsidiary installations were used to measure the real contact area between steel-ball and sheet aluminium, and the acoustic image of real contact area was obtained. It shows that the real contact area increases with loading time; the greater the load, the larger the real contact area owing the occurrence of plastic deformation in the contact area; and the lubricants notably influence the measuring result of real contact area. This acoustic method can measure the real contact area between two surfaces in relative moving under the condition of continuous loading in situ without the critical requirement of being transparent bodies as the optical method does.
In-Process Measurement of Contact Pattern Variations in Rotating Main Bearing of Machine Tools Using Ultrasonic Waves Method.

Chikao Inaba,Iwao Murase,Hidenori Shinno,Yoshimi Ito

DOI: https://doi.org/10.1299/kikaic.61.3375

1995-01-01

TRANSACTIONS OF THE JAPAN SOCIETY OF MECHANICAL ENGINEERS Series C

Abstract:It can be pointed out that characteristics of machine tool joints have a significant effect on the static, dynamic and thermal behavior of a machine tool as a whole. To clarify various characteristics of the joint, it is basically essential to evaluate the contact pressure and its distribution. With regard to the measurement of the static contact pressure of the joint, one of the authors has already proposed a method using ultrasonic waves. In contrast, the joint behavior in the machine work condition is not revealed as yet. In this study, therefore, an ultrasonic waves method for the in-process measurement of contact pattern variations has been proposed, and its characteristics have also been investigated. The objective of the study is the joint between the bearing and its housing in the main spindle system. The method has a remarkable feature in that it is continuously applicable in operation without changing the state of contact at the joint. From the experimental results, it is ascertained that the proposed method is available for detecting the contact pattern variations significantly influenced by the thermal expansion of the outer ring of the bearing.
Angular Measurement of Acoustic Reflection Coefficients by the Inversion of V(z, T) Data with High Frequency Time-Resolved Acoustic Microscopy

Jian Chen,Xiaolong Bai,Keji Yang,Bing-Feng Ju

DOI: https://doi.org/10.1063/1.3677327

2012-01-01

Abstract:For inspection of mechanical properties and integrity of critical components such as integrated circuits or composite materials by acoustic methodology, it is imperative to evaluate their acoustic reflection coefficients, which are in close correlation with the elastic properties, thickness, density, and attenuation and interface adhesion of these layered structures. An experimental method based on angular spectrum to evaluate the acoustic coefficient as a function of the incident angle, θ, and frequency, ω, is presented with high frequency time-resolved acoustic microscopy. In order to achieve a high spatial resolution for evaluation of thin plates with thicknesses about one or two wavelengths, a point focusing transducer with a nominal center frequency of 25 MHz is adopted. By measuring the V(z, t) data in pulse mode, the reflection coefficient, R(θ, ω), can be reconstructed from its two-dimensional spectrum. It brings simplicity to experimental setup and measurement procedure since only single translation of the transducer in the vertical direction is competent for incident angle and frequency acquisition. It overcomes the disadvantages of the conventional methods requiring the spectroscopy for frequency scanning and/or ultrasonic goniometer for angular scanning. Two substrates of aluminum and Plexiglas and four stainless plates with various thicknesses of 100 μm, 150 μm, 200 μm, and 250 μm were applied. The acoustic reflection coefficients are consistent with the corresponding theoretical calculations. It opened the way of non-destructive methodology to evaluate the elastic and geometrical properties of very thin multi-layers structures simultaneously.
Numerical and experimental investigation on ball motion with oil rheology and thermal effect in high speed ball bearings

Cheng Peng,Hongrui Cao,Kaikai Liu,Yang Luo,Jianghai Shi

DOI: https://doi.org/10.1016/j.triboint.2023.109242

IF: 5.62

2024-01-05

Tribology International

Abstract:Dynamic behavior of rolling elements determines the performance including the extent of skidding and wear in ball bearings, which are influenced by many factors. A comprehensive investigation of dynamic behaviors of high speed ball bearings has been conducted both numerically and experimentally. The dynamic model of high speed ball bearings applicable to a wide range of shaft speeds has been developed, taking into account rheological behavior of lubricating oil, curvature effect, collision between balls and cage and thermal effect. Analyses of ball speeds and interaction forces, as well as sliding speed within ball-raceway contact ellipse have been carried out. The ball-to-race ratio (BRR) of speed has been studied specifically under various operating conditions to reflect the cage speed with high precision. A set of experiments have accordingly been performed on a test rig where optic fiber transducer was employed to obtain the orbital speed of ball. The increase of orbital speed of ball with shaft speed was observed in experiments under different axial load. Numerical results from dynamic simulations also agree with the experimental results based on the investigated ball bearing. The present model is versatile over a wide range of operating conditions.

engineering, mechanical
Instrumentation of a Rolling Bearing with a Thin Film Piezo Coating for Oil Film Measurement

R. S. Dwyer-Joyce,B. W. Drinkwater,J. Zhang,J. Elgoyhen,K. J. Kirk

DOI: https://doi.org/10.1115/ijtc2007-44228

2007-01-01

Abstract:This paper describes a novel design of oil-film monitoring sensor capable of measuring oil-film thickness in concentrated contacts. The approach is to use a thin (approx. 4 μm) sputtered coating of piezoelectric material, such as Aluminium Nitride. When correctly electroded this acts as an ultrasonic sensor with a usable bandwidth from 20–350 MHz. This sensor allows the interrogation of the small lubricated region between the ball and raceway without any special focusing requirements. Typically the dimensions of the contact region is less than a millimeter wide. This sensor system is then demonstrated experimentally on a deep groove ball bearing with the piezoelectric thin film on the external surface of the bearing outer raceway. The interaction of ultrasound with the oil-film is modeled using a quasi-static spring model and this allows properties such as film thickness to be extracted. The measured thicknesses are shown to agree well those obtained from classical elastohydrodynamic lubrication theory for the high bearing loads and low speeds where several data points can be collected from the contact during a ball passage. Measurement of oil film thickness in the region of 0.1–1 μm is demonstrated.
Monitoring of Lubricant Film Failure in a Ball Bearing Using Ultrasound

Jie Zhang,Bruce W. Drinkwater,Rob S. Dwyer-Joyce

DOI: https://doi.org/10.1115/1.2197848

2006-03-20

Journal of Tribology

Abstract:A lubricant-film monitoring system for a conventional deep groove ball bearing (type 6016, shaft diameter 80 mm, ball diameter 12.7 mm) is described. A high-frequency (50 MHz) ultrasonic transducer is mounted on the static outer raceway of the bearing. The transducer is focused on the ball-raceway interface and used to measure the reflection coefficient of the lubricant in the “contact” ellipse between bearing components. The reflection coefficient characterizes the lubricant film and can be used to calculate its thickness. An accurate triggering system enables multiple reflection measurements to be made as each lubricated contact moves past the measurement location. Experiments are described in which bearings were deliberately caused to fail by the addition of acetone, water, and sand to the lubricant. The ultrasonic reflection coefficient was monitored as a function of time as the failure occurred. Also monitored were the more standard parameters, temperature and vibration. The results indicate that the ultrasonic measurements are able to detect the failures before seizure. It is also observed that, when used in parallel, these monitoring techniques offer the potential to diagnose the failure mechanism and hence improve predictions of remaining life.
Ultrasonic measurement of contact stress at metal-to-metal interface based on a real rough profile through modeling and experiment

Ting Han,Jianchun Fan

DOI: https://doi.org/10.1016/j.measurement.2023.113046

2023-05-22

Measurement: Journal of the International Measurement Confederation

Abstract:Metal-to-metal seals are widely used in tubing and casing connections in oil and gas wells; therefore, the integrity of sealing is crucial. As the quality of seals is directly influenced by the metal-to-metal contact stress, this study investigates the measurement and evaluation of contact stress at rough interfaces numerically and experimentally using an ultrasonic quantitative method. A two-dimensional ultrasonic propagation model of the rough contact interface is developed based on an actual rough profile. The reflection coefficient decreases gradually as the normal deformation and contact rate increase, and a relationship between the reflection coefficient and the contact rate is established. The reflection coefficient reduces exponentially to approximately zero when the contact rate is less than 0.5. Combined with the contact mechanics theory, for an elastic contact, an empirical fitting formula for the interface reflection coefficient, contact stress, root mean square deviation (Rq), and mean width of the profile elements (RSm) is established. Note that at the same contact rate, the reflection coefficient decreases as the interface lubricant parameter ρc 2 increases. Therefore, ρc 2 is introduced to optimize the empirical fitting formula. Accuracy of the empirical fitting formula is verified using experimental results, that is, through the ultrasonic measurement of the contact stress at the loaded metal-to-metal interface. Thus, this study serves as a reference for measuring and quantifying the metal-to-metal contact stress.
Experimental investigations to assess surface fatigue failure in rolling contact bearing

Santhosh Kumar Kamarapu,Amarnath Muniyappa,Perumalla Sateesh Kumar,Deepak Kumar Prasad,Bajane Srinivasa Ajay Vardhaman

DOI: https://doi.org/10.1177/14644207241254448

2024-05-29

Proceedings of the Institution of Mechanical Engineers Part L Journal of Materials Design and Applications

Abstract:Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, Ahead of Print. Rolling element bearings are the most important components in almost all rotating machines. These bearings are often subjected to repetitive load cycles at different operating conditions. Excessive loads, speeds, and improper operating conditions lead to the propagation of defects on their load-bearing surfaces, thereby causing a negative impact on the performance of rotating machines. This paper presents the results of experimental investigations to assess wear propagation in roller bearings using lubricant degradation, vibration, and statistical parameter analysis methods. A roller bearing setup was developed in the laboratory, and the test bearing (NJ 307E) was subjected to fatigue tests over a period of 900 h. The bearing was operated at a speed and radial load of 800 rpm and 1 kN, respectively. The film thickness analysis revealed a transition in lubrication regimes during 600–900 h of operation. Grease structure degradation and oxidation analyses were carried out using scanning electron microscope images and the Fourier transform infrared radiation technique. Further, the vibration signals are extracted from the bearing housing at regular intervals. Using the fast Fourier transform technique, these vibration signals were used to analyze bearing fault frequencies to highlight the faults developed on bearing contact surfaces. The statistical features of vibration signals such as root mean square, kurtosis, and crest factor were used to assess the severity of wear propagated on the bearing contact surfaces. Integrating tribological and vibration parameter analysis techniques provided a reliable assessment of surface fatigue wear propagated on the roller-bearing contact surfaces.

materials science, multidisciplinary
Study on the Propagation Characteristics of Acoustic Emission in Point Contact Bearing Ball

Yanyan Xiao,Wenxiu Lu,Fulei Chu

DOI: https://doi.org/10.4028/www.scientific.net/amm.365-366.634

2013-01-01

Applied Mechanics and Materials

Abstract:Acoustic Emission (AE) signal has been used pervasively in the extraction of fault feature and the location of damage. The precision of the extraction and location is determined by the propagation characteristics of AE signal in different structures. In this paper, the propagation characteristics of AE wave in the point contact sphere under continuous and transient AE signal is analyzed; a series of experiments under different condition are conducted; based on wave propagation theory, a simulation model is built using the software of ANSYS LS-DYNA. The results of experiments and simulation models reveal that the propagation characteristics-attenuation, frequency features-of AE signal can be manifested clearly in the experiments and are simulated correctly by the simulation model.
Inline Measurement of Acoustoelastic Coefficient in Conductive Sheet Material With Electromagnetic Loading System

Chuang Zhang,Biao Wang,Suzhen Liu,Qingxin Yang

DOI: https://doi.org/10.1109/jsen.2020.3019250

IF: 4.3

2021-01-15

IEEE Sensors Journal

Abstract:In ultrasonic non-destructive testing technology, the method to detect the stress of metal plates using longitudinal critically refracted waves (L<sub>CR</sub>) is increasingly developing, in which the calculation of acoustoelastic coefficient of the metal plate is indispensable. However, due to the influence of the metallic material's in-service environment on acoustoelastic coefficient, the existing calculation method of the acoustoelastic coefficient cannot meet the engineering requirements. Therefore, an inline measurement method based on electromagnetic loading is proposed in this paper. The calculation formula for the inline measurement of acoustoelastic coefficient is derived. An electromagnetic loading experimental platform is designed, including an electromagnetic loading module, an ultrasonic detecting module, and a delay control module. The loading test of a 1060 aluminum plate is carried out using the designed platform. The flight time of L<sub>CR</sub> waves is measured experimentally and used in the calculation formula of acoustoelastic coefficient. The experimental results of acoustoelastic coefficient meet the accuracy requirement of less than 5%, which can be used for stress measurement. So, the inline measurement method of acoustoelastic coefficient proposed in this paper is feasible.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Experimental Analysis of Interface Contact Behavior Using a Novel Image Processing Method

Jingyu Han,Zhijun Luo,Yuling Zhang,Shaoze Yan

DOI: https://doi.org/10.1088/1674-1056/abd696

2020-01-01

Chinese Physics B

Abstract:The spatial and temporal evolution of real contact area of contact interface with loads is a challenge. It is generally believed that there is a positive linear correlation between real contact area and normal load. However, with the development of measuring instruments and methods, some scholars have found that the growth rate of real contact area will slow down with the increase of normal load under certain conditions, such as large-scale interface contact with small roughness surface, which is called the nonlinear phenomenon of real contact area. At present, there is no unified conclusion on the explanation of this phenomenon. We set up an experimental apparatus based on the total reflection principle to verify this phenomenon and analyze its mechanism. An image processing method is proposed, which can be used to quantitative analysis micro contact behaviors on macro contact phenomenon. The weighted superposition method is used to identify micro contact spots, to calculate the real contact area, and the color superimposed image is used to identify micro contact behaviors. Based on this method, the spatiotemporal evolution mechanism of real contact area nonlinear phenomena is quantitatively analyzed. Furthermore, the influence of nonlinear phenomenon of real contact area on the whole loading and unloading process is analyzed experimentally. It is found that the effects of fluid between contact interface, normal load amplitude and initial contact state on contact behavior cannot be ignored in large-scale interface contact with small roughness surface.
A general method for impact dynamic analysis of a planar multi-body system with a rolling ball bearing joint

Li-xin Xu

DOI: https://doi.org/10.1007/s11071-014-1482-2

IF: 5.741

2014-06-25

Nonlinear Dynamics

Abstract:Impact affects the dynamic characteristics of mechanical multi-body systems and damages those rotating parts, such as the joint rolling element bearings, which are high-precision, defect intolerant components. Based on multi-body dynamic theory, Hertzian contact theory, and a continuous contact model, this study proposed a modelling method that can describe the dynamic behaviour of planar mechanical multi-body systems containing a rolling ball bearing joint under impact. In this method, the rigid bodies and bearing joint were connected according to their joint force constraints; the impact constraint between the multi-body system and the target rigid body was constructed using a continuous contact force model. Based on this method, the reflection relationship between the external impacts of the mechanical multi-body system and the variation law governing the dynamic load on the rolling bearing joint were revealed. Subsequently, an impact multi-body system, which was composed of a sliding–crank mechanism containing a rolling ball bearing joint and the target rigid body with an elastic support, was analysed to explore the dynamic response of such a complex discontinuous dynamic system andthe relevant relationship governing the dynamic load on the rolling bearing joint. In addition, a multi-body dynamic simulation software was used to build a virtual prototype of the impact slider–crank system. Compared with the theoretical model, the prototype had an additional deep groove ball bearing. That is to say, the prototype model took account of the specific geometric structural characteristics and the complex contact relationship of the inner and outer races, rolling balls, and bearing cage. Finally, the effectiveness of the theoretical method proposed in this study was verified by comparative analysis of the results. The results suggested that the external impact of a mechanical multi-body system was prone to induce sudden changes in the equivalent reaction force on its bearing joint and the dynamic load carried on its rolling balls. This study provided an effective method for exploring the distribution characteristics of dynamic loads on rolling ball bearing joints under working impact load conditions. Moreover, it offered support for the parameter optimisation of geometric structure, performance evaluation, and dynamic design of the rolling ball bearings.

engineering, mechanical,mechanics
Calibration of Oil Film Thickness Acoustic Reflection Coefficient of Bearing under Multiple Temperature Conditions

Fei Shang,Bo Sun,Shaofeng Wang,Yongquan Han,Wenjing Liu,Ning Kong,Yuwu Ba,Fengchun Miao,Zhendong Liu

DOI: https://doi.org/10.3390/lubricants12040125

2024-04-08

Lubricants

Abstract:Rolling mill bearings are prone to wear, erosion, and other damage characteristics due to prolonged exposure to rolling forces. Therefore, regular inspection of rolling mill bearings is necessary. Ultrasonic technology, due to its non-destructive nature, allows for measuring the oil film thickness distribution within the bearing during disassembly. However, during the process of using ultrasonic reflection coefficients to determine the oil film thickness and distribution state of rolling mill bearings, changes in bearing temperature due to prolonged operation can occur. Ultrasonic waves are susceptible to temperature variations, and different temperatures of the measured structure can lead to changes in measurement results, ultimately distorting the results. This paper proposes using density and sound speed compensation methods to address this issue. It simulates and analyzes the oil film reflection coefficients at different temperatures, ultimately confirming the feasibility and effectiveness of this approach. The paper establishes a functional relationship between bearing pressure and reflection coefficients, oil film thickness, and reflection coefficients. This allows for the compensation of reflection coefficients under any pressure conditions, enhancing the accuracy of oil film thickness detection. The proposed method provides technical support for the maintenance of plate rolling processes in the steel industry.
Research on the stiffness characteristics and contact status of matched angular contact ball bearings considering the effect of varying spatial position of rolling ball

Jianguo Gu,Junyan Yang,Shengdong Zhang,Zhang Xinglei,Shihui You

DOI: https://doi.org/10.1177/09544062241285412

2024-10-08

Proceedings of the Institution of Mechanical Engineers Part C Journal of Mechanical Engineering Science

Abstract:Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, Ahead of Print. In engineering practice, bearings used as support components are usually installed in pairs in various rotating machines. The mechanical and contact characteristics of bearings play a crucial role in determining the operational accuracy, safety performance and stability of equipment. Numerous studies focused on single bearings have been reported form diffident aspects for enhancing service performance. However, the literature reports on the matched bearings are scarce due to the mutual coupling of rolling elements and the extremely complex stress conditions. Especially the stiffness fluctuation and internal contact status affected by the ball position are difficult to be observed and tested experimentally because of the complex and compact structure, which significantly impacts the safe and reliable operation of rotating machines. To overcome the above shortcomings, this paper investigates the effect of ball position on the stiffness characteristics and contact status of matched angular contact ball bearings based on the coordinate matrix transformation approach and Jones' statics model. Then, the stiffness results of published literature are used as a benchmark to validate the accuracy of solution method of this paper. Finally, 7206B bearings with different installing forms are used as a numerical example to reveal the effect of ball position on the stiffness characteristics and contact status of matched angular contact ball bearings under different working conditions. The study provides a scientific guidance to investigate the mechanical characteristics and contact mechanism of multi-bearing system.

engineering, mechanical
Research on Electrostatic Monitoring of Tribo-Contacts with Dynamic Adaptive Fusion Method

Ruochen Liu,Han Wang,Jinwu Zhang,Shuangshuang Gu,Jianzhong Sun

DOI: https://doi.org/10.1155/2022/8952349

IF: 1.43

2022-01-04

Mathematical Problems in Engineering

Abstract:Electrostatic monitoring is a unique and rapid developing technique applied in the prognostics and health management of the tribological system based on electrostatic charging and sensing phenomenon. It has considerable advantages in condition monitoring of tribo-contacts with high sensitivity and resolution. Unfortunately, the monitoring result can be affected due to the switch of operating conditions that reduces its accuracy. This paper presents a dynamic adaptive fusion approach, moving window local outlier factor based on electrostatic features to overcome the influence. Life cycle experiments of rolling bearings and railcar gearbox were carried out on an electrostatic monitoring platform. The MWLOF method was used to extract and analyze the experimental data, combined with the Pauta criterion to judge wear faults quantitatively, and compare with other feature extraction results. It is verified that the proposed method can overcome the influence of changes in working conditions on the monitoring results, improve the monitoring sensitivity, and provide an accurate reference for friction and wear faults.

engineering, multidisciplinary,mathematics, interdisciplinary applications
Design and Experimental Research of a Non-Destructive Detection Device for High-Precision Cylindrical Roller Dynamic Unbalance

Zhuangya Zhang,Baorun Yang,Mingde Duan,Ruijie Gu,Shijie Liang,Yang Chen

DOI: https://doi.org/10.3390/machines12100684

IF: 2.899

2024-09-30

Machines

Abstract:Due to their small size and light mass, small precision cylindrical rollers present challenges in dynamic unbalance detection, including difficulties in measurement and the risk of surface damage. This paper proposes a non-destructive detection device for assessing the dynamic unbalance of small precision cylindrical rollers. The device utilizes an air flotation support method combined with resonance amplification to indirectly measure the dynamic unbalance. A dynamic model of the air flotation tooling-cylindrical roller vibration system was developed to explore the relationship between the vibration parameters of the air flotation tooling and the dynamic unbalance of the cylindrical roller. Modal analysis and harmonic response analysis were performed, revealing that the amplitude of the vibration system at resonance could be detected using the sensor. Additionally, modal testing was conducted to determine the natural frequency of the system. A non-destructive detection platform was constructed for testing the dynamic unbalance of cylindrical rollers. Microscopic observation of the roller surface before and after testing confirmed that the device successfully performs non-destructive detection of dynamic unbalance.

engineering, mechanical, electrical & electronic

Relationship between testosterone and erectile dysfunction.

Mullerian adenosarcoma of the uterus associated with long-term oral contraceptive use.

In situ evaluation of contact stiffness in a slip interface with different roughness conditions using ultrasound reflectometry

Wear monitoring of bearing steel using electrostatic and acoustic emission techniques

Application Study of Acoustic Reflectivity Based on Phased Array Ultrasonics in Evaluating Lubricating Oil Film Thickness

Research of real contact area through acoustic microscope

In-Process Measurement of Contact Pattern Variations in Rotating Main Bearing of Machine Tools Using Ultrasonic Waves Method.

Angular Measurement of Acoustic Reflection Coefficients by the Inversion of V(z, T) Data with High Frequency Time-Resolved Acoustic Microscopy

Numerical and experimental investigation on ball motion with oil rheology and thermal effect in high speed ball bearings

Instrumentation of a Rolling Bearing with a Thin Film Piezo Coating for Oil Film Measurement

Monitoring of Lubricant Film Failure in a Ball Bearing Using Ultrasound

Ultrasonic measurement of contact stress at metal-to-metal interface based on a real rough profile through modeling and experiment

Experimental investigations to assess surface fatigue failure in rolling contact bearing

Study on the Propagation Characteristics of Acoustic Emission in Point Contact Bearing Ball

Inline Measurement of Acoustoelastic Coefficient in Conductive Sheet Material With Electromagnetic Loading System

Experimental Analysis of Interface Contact Behavior Using a Novel Image Processing Method

A general method for impact dynamic analysis of a planar multi-body system with a rolling ball bearing joint

Calibration of Oil Film Thickness Acoustic Reflection Coefficient of Bearing under Multiple Temperature Conditions

Research on the stiffness characteristics and contact status of matched angular contact ball bearings considering the effect of varying spatial position of rolling ball

Research on Electrostatic Monitoring of Tribo-Contacts with Dynamic Adaptive Fusion Method

Design and Experimental Research of a Non-Destructive Detection Device for High-Precision Cylindrical Roller Dynamic Unbalance