Solution design for Low Fluorine Trifluoroacetate route to YBa 2 Cu 3 O 7 1 films 2 3

X. Palmer,C. Pop,H. Eloussifi,B. Villarejo,P. Roura,J. Farjas,A. Calleja,A. Palau,X. Obradors,T. Puig,S. Ricart

Abstract:

What problem does this paper attempt to address?

Separator Characteristics for Increasing Performance of Microbial Fuel Cells

Xiaoyuan Zhang,Shaoan Cheng,Xin Wang,Xia Huang,Bruce E. Logan

DOI: https://doi.org/10.1021/es901631p

IF: 11.4

2009-01-01

Environmental Science & Technology

Abstract:Two challenges for improving the performance of air cathode, single-chamber microbial fuel cells (MFCs) include increasing Coulombic efficiency (CE) and decreasing internal resistance. Nonbiodegradable glass fiber separators between the two electrodes were shown to increase power and CE, compared to cloth separators (J-cloth) that were degraded over time. MFC tests were conducted using glass fiber mats with thicknesses of 1.0 mm (GF1) or 0.4 mm (GF0.4), a Cation exchange membrane (CEM), and a J-cloth (JC), using reactors with different configurations. Higher power densities were obtained with either GF1 (46 +/- 4 W/m(3)) or JC (46 +/- 1 W/m(3)) in MFCs with a 2 cm electrode spacing, when the separator was placed against the cathode (S-configuration), rather than MFCs with GF0.4 (36 +/- 1 W/m(3)) or CEM (14 +/- 1 W/m(3)). Power was increased to 70 +/- 2 W/m(3) by placing the electrodes on either side of the GF1 separator (single separator electrode assembly, SSEA) and further to 150 +/- 6 W/m(3) using two sets of electrodes spaced 2 cm apart(double separator electrode assembly, DSEA). Reducing the DSEA electrode spacing to 0.3 cm increased power to 696 +/- 26 W/m(3) as a result of a decrease in the ohmic resistance from 5.9 to 2.2 Omega. The main advantages of a GF1 separator compared to JC were an improvement in the CE from 40% to 81% (S-configuration), compared to only 20-40% for JC under similar conditions, and the fact that GF1 was not biodegradable, The high CE for the GF1 separator was attributed to a low oxygen mass transfer coefficient (k(0) = 5.0 x 10(-5) cm/s).The GF1 and JC materials differed in the amount of biomass that accumulated on the separator and its biodegradability, which affected long-term power production and oxygen transport. These results show that materials and mass transfer properties of separators are important factors for improving power densities, CE, and long-term performance of MFCs.
Recent advances in the separators for microbial fuel cells.

Wen-Wei Li,Guo-Ping Sheng,Xian-Wei Liu,Han-Qing Yu

DOI: https://doi.org/10.1016/j.biortech.2010.03.090

IF: 11.4

2011-01-01

Bioresource Technology

Abstract:Separator plays an important role in microbial fuel cells (MFCs). Despite of the rapid development of separators in recent years, there are remaining barriers such as proton transfer limitation and oxygen leakage, which increase the internal resistance and decrease the MFC performance, and thus limit the practical application of MFCs. In this review, various separator materials, including cation exchange membrane, anion exchange membrane, bipolar membrane, microfiltration membrane, ultrafiltration membranes, porous fabrics, glass fibers, J-Cloth and salt bridge, are systematically compared. In addition, recent progresses in separator configuration, especially the development of separator electrode assemblies, are summarized. The advances in separator materials and configurations have opened up new promises to overcome these limitations, but challenges remain for the practical application. Here, an outlook for future development and scaling-up of MFC separators is presented and some suggestions are highlighted.
A Comprehensive Study of Custom-Made Ceramic Separators for Microbial Fuel Cells: Towards “Living” Bricks

Jiseon You,Lauren Wallis,Nevena Radisavljevic,Grzegorz Pasternak,Vincenzo M. Sglavo,Martin M Hanczyc,John Greenman,Ioannis Ieropoulos

DOI: https://doi.org/10.3390/en12214071

IF: 3.2

2019-10-25

Energies

Abstract:Towards the commercialisation of microbial fuel cell (MFC) technology, well-performing, cost-effective, and sustainable separators are being developed. Ceramic is one of the promising materials for this purpose. In this study, ceramic separators made of three different clay types were tested to investigate the effect of ceramic material properties on their performance. The best-performing ceramic separators were white ceramic-based spotty membranes, which produced maximum power outputs of 717.7 ± 29.9 μW (white ceramic-based with brown spots, 71.8 W·m−3) and 715.3 ± 73.0 μW (white ceramic-based with red spots, 71.5 W·m−3). For single material ceramic types, red ceramic separator generated the highest power output of 670.5 ± 64. 8 μW (67.1 W·m−3). Porosity investigation revealed that white and red ceramics are more porous and have smaller pores compared to brown ceramic. Brown ceramic separators underperformed initially but seem more favourable for long-term operation due to bigger pores and thus less tendency of membrane fouling. This study presents ways to enhance the function of ceramic separators in MFCs such as the novel spotty design as well as fine-tuning of porosity and pore size.

energy & fuels
Characterization and application of novel fly ash blended ceramic membrane in MFC for low-cost and sustainable wastewater treatment and power generation

Ankit Rao,Anubha Kaushik,Gunaseelan Kuppurangan,Gajalakshmi Selvaraj

DOI: https://doi.org/10.1007/s11356-023-25327-8

Abstract:Field-scale application of the microbial fuel cell (MFC) technology faces a major constraint due to the widely used high-cost proton exchange membrane Nafion, prompting lately, the development of ceramic membranes using different clay minerals. In the present study, the characteristics and applicability of a novel ceramic membrane fabricated using potter's clay (C) blended with varying proportions (0, 5, 10, and 20 wt%) of fly ash (FA), designated as CFA0, CFA5, CFA10, and CFA20, were assessed for cost-effective and sustainable use in MFC. On assessing the properties of the membrane, CFA10 was found to exhibit superior quality with fine pore size distribution (average 0.49 μm) favoring higher water uptake and less oxygen diffusion. The CFA10 membrane showed a maximum proton mass transfer coefficient (4.32 ± 0.04 × 10-5 cm/s) that was about three times that of the control CFA0. The oxygen mass transfer coefficient of CFA10 was 5.13 ± 0.12 × 10-5 cm/s, which was about 40% less than in the control. X-ray diffraction (XRD) analysis of CFA membrane revealed the richness of quartz, which facilitates proton conductance and water retention. The CFA10 membrane fitted MFC demonstrated a peak power output of 4.57 W/m3 (twice that in CFA0) with an average of 80.02 ± 0.86% COD removal and 68.03 ± 0.13% coulombic efficiency in a long-term study indicating its improved applicability and durability. Electrochemical kinetics involving cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) also affirmed the efficacy of CFA10 membrane in MFC showing peak current output of 13.95 mA and low ohmic resistance (74.2 Ω). The novel (CFA10) ceramic membrane amalgamated with the coal fly ash, a waste of concern, shows promise for high MFC performance at a much reduced (98% less) cost that can be used for sustainable scale-up of the technology.
Tubular ceramic performance as separator for microbial fuel cell: A review

M.F. Hil Me,M.H. Abu Bakar

DOI: https://doi.org/10.1016/j.ijhydene.2019.08.115

IF: 7.2

2020-08-01

International Journal of Hydrogen Energy

Abstract:The depletion of unsustainable conventional energy sources and global warming issues create world demand for green energy sources. The microbial fuel cell (MFC) technology with the capability to convert environmental waste to energy can be improved with cheap ceramic material. The ceramic is structurally porous, thus allow a direct exchange of cation. The ceramic material also enhances stability thermally and chemically, non-ion selective characteristic, high mechanical strength, and easily washable. Commercially produced ceramic structures have been proven to reduce Chemical Oxygen Demand up to 92% and allow high power output. It is also comparatively durable in the long-term operation of MFC, compared to the commercially available membrane. The novelty of using tubular design is the efficient use of space, which leads to the possibility of scaling up. As a conclusion, a combination of both ceramic material and tubular design could be an excellent alternative separator for MFC.

energy & fuels,electrochemistry,chemistry, physical
Development of a Novel Composite Polymer Electrolyte Membrane for Application as a Separator in a Dual Chamber Microbial Fuel Cell

Parini Vrajesh Surti,Suresh Kumar Kailasa,Arvind Kumar Mungray

DOI: https://doi.org/10.1021/acs.iecr.3c04280

2024-03-15

Industrial & Engineering Chemistry Research

Abstract:The quest for developing sustainable energy devices has put microbial fuel cells (MFCs) at the forefront of research in recent years. However, the use of synthetic polymer electrolyte membranes (PEMs) such as Nafion is a compromise in the sustainability of this technology. A novel eco-friendly composite PEM has been developed using poly(vinyl alcohol) (PVA) and k-carrageenan (kC) as membrane precursors. Cation exchangers such as vermiculite and imidazole-grafted vermiculite were augmented to the base membrane PVA-kC for developing PEM, called VPC and IPC, respectively. The proton mass transfer of VPC and IPC increased by 57 and 38%, while their oxygen mass transfer decreased by 45 and 44%, respectively, with respect to PVA-kC. Double-chambered MFCs were deployed with the developed PEMs, namely, PVA-kC (PMFC), VPC (VMFC), IPC (IMFC), and commercial Nafion (NMFC), for synthetic wastewater treatment in the aerated cathode configuration and dye decolorization with a ferricyanide cathode. The highest power density of 182 mW·m–3 was obtained with VMFC, followed by IMFC (164 mW·m–3), NMFC (145 mW·m–3), and PMFC (128 mW·m–3), in the aerated cathode MFC. The decolorization percentage increased in the order of PMFC (49%) < NMFC (55%) < IMFC (58%) < VMFC (65%). The cation-exchanger-augmented PVA-kC membrane can be used as a suitable alternative to Nafion in MFCs.

engineering, chemical
Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.

Wulin Yang,Ruggero Rossi,Yushi Tian,Kyoung-Yeol Kim,Bruce E. Logan

DOI: https://doi.org/10.1016/j.biortech.2017.10.109

IF: 11.4

2017-01-01

Bioresource Technology

Abstract:Microbial fuel cell (MFC) cathodes rapidly foul when treating domestic wastewater, substantially reducing power production over time. Here a wipe separator was chemically bonded to an activated carbon air cathode using polyvinylidene fluoride (PVDF) to mitigate cathode fouling and extend cathode performance over time. MFCs with separator-bonded cathodes produced a maximum power density of 190 +/- 30 mW m(-2) after 2 months of operation using domestic wastewater, which was similar to 220% higher than controls (60 +/- 50 mW m(-2)) with separators that were not chemically bonded to the cathode. Less biomass (protein) was measured on the bonded separator surface than the non-bonded separator, indicating chemical bonding reduced external bio-fouling. Salt precipitation that contributed to internal fouling was also reduced using separator-bonded cathodes. Overall, the separator-bonded cathodes showed better performance over time by mitigating both external bio-fouling and internal salt fouling.
Unlaminated Carbon As Separator In Air-Cathode Single-Chamber Microbial Fuel Cells

Xiaoyuan Zhang,Xin Wang,Shaoan Cheng,Xia Huang,Bruce E. Logan

2009-01-01

Abstract:Air-cathode single-chamber microbial fuel cells (MFCs) have potential for practical applications in bioenergy production. One of the main challenges is that the coulombic efficiency (CE) is relatively low compared with MFCs that contain a membrane. In this study, unlaminated carbon was used as separator in MFCs with three different configurations to enhance the CE and to increase power by shortening the distance between the anode and cathode. A CE of 28% (1000 Ω load) was obtained in the MFC using the unlaminated carbon as a separator on the cathode side with 2 cm distance between the anode and cathode, which was an increase of 50% compared to a control lacking a separator. The CE was further enhanced to 47% (1000 Ω) using a separator electrode assembly (SEA) configuration, where the separator was sandwiched between the anode and cathode. The power density also was increased by the SEA configuration, and the internal resistance decreased from 64 Ω (2 cm electrodes space) to 41 Ω (SEA). A double SEA MFC (with the pairs of electrodes 2 cm apart) produced 41 W/m3, which is an increase of 140% compared to that with single electrodes spaced 2 cm apart. This study showed that a separator could increase the CE, and that the use of separators allows a smaller distance between the electrodes that can increase reactor performance.
The use of nylon and glass fiber filter separators with different pore sizes in air-cathode single-chamber microbial fuel cells

Xiaoyuan Zhang,Shaoan Cheng,Xia Huang,Bruce E. Logan

DOI: https://doi.org/10.1039/b927151a

IF: 32.5

2010-01-01

Energy & Environmental Science

Abstract:Separators are needed in microbial fuel cells (MFCs) to reduce electrode spacing and preventing electrode short circuiting. The use of nylon and glass fiber filter separators in single-chamber, air-cathode MFCs was examined for their effect on performance. Larger pore nylon mesh were used that had regular mesh weaves with pores ranging from 10 to 160 mu m, while smaller pore-size nylon filters (0.2-0.45 mu m) and glass fiber filters (0.7-2.0 mu m) had a more random structure. The pore size of both types of nylon filters had a direct and predictable effect on power production, with power increasing from 443 +/- 27 to 650 +/- 7 mW m(-2) for pore sizes of 0.2 and 0.45 mu m, and from 769 +/- 65 to 941 +/- 47 mW m(-2) for 10 to 160 mu m. In contrast, changes in pore sizes of the glass fiber filters resulted in a relatively narrow change in power (732 +/- 48 to 779 +/- 43 mW m(-2)) for pore sizes of 0.7 to 2 mu m. An ideal separator should increase both power density and Coulombic efficiency (CE). However, CEs measured for the different separators were inversely correlated with power production, demonstrating that materials which reduced the oxygen diffusion into the reactor also hindered proton transport to the cathode, reducing power production through increased internal resistance. Our results highlight the need to develop separators that control oxygen transfer and facilitate proton transfer to the cathode.
An Expanded Clay-Coated Separator with Unique Microporous Structure for Enhancing Electrochemical Performance of Rechargeable Hybrid Aqueous Batteries

Liu Yao,Li Dongni,Xu Hang,Jiang Yinshan,Li Fangfei,Xue Bing

DOI: https://doi.org/10.1007/s10008-018-4124-7

IF: 2.747

2018-01-01

Journal of Solid State Electrochemistry

Abstract:In this study, a novel composite separator for rechargeable hybrid aqueous batteries is successfully fabricated by coating porous expanded dickite aqueous slurry using polyacrylic latex as the binder on ES (Ethylene-Propylene Side By Side) nonwoven. The porous expanded dickite is prepared by intercalation and violent chemical reaction, forming porous structure with pore size of 0.3–1.2 μm. The porous morphology of the composite separators could be fine-tuned by varying the content of expanded dickite. The air permeability, porosity, electrolyte uptake, and ionic conductivity of the composite separators gradually improve with the increase of the content of expanded dickite. The improved performance of composite separators helps to improve battery performance, especially at high expanded dickite content. The composite separators with 90 wt.% expanded dickite provide superior cell performance owing to well-tailored pore structure, as compared to a commercialized absorbed glass mat (AGM).
Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

guang chen,fang zhang,bruce e logan,michael a hickner

DOI: https://doi.org/10.1016/j.elecom.2013.05.026

IF: 5.443

2013-01-01

Electrochemistry Communications

Abstract:High-performance microbial fuel cell (MFC) air cathodes were constructed using a combination of inexpensive materials for the oxygen reduction cathode catalyst and the electrode separator. A poly(vinyl alcohol) (PVA)-based electrode separator enabled high coulombic efficiencies (CEs) in MFCs with activated carbon (AC) cathodes without significantly decreasing power output. MFCs with AC cathodes and PVA separators had CEs (43%–89%) about twice those of AC cathodes lacking a separator (17%–55%) or cathodes made with platinum supported on carbon catalyst (Pt/C) and carbon cloth (CE of 20%–50%). Similar maximum power densities were observed for AC-cathode MFCs with (840±42mW/m2) or without (860±10mW/m2) the PVA separator after 18cycles (36 days). Compared to MFCs with Pt-based cathodes, the cost of the AC-based cathodes with PVA separators was substantially reduced. These results demonstrated that AC-based cathodes with PVA separators are an inexpensive alternative to expensive Pt-based cathodes for construction of larger-scale MFC reactors.
Vermiculite nanosheet augmented novel proton exchange membrane for microbial fuel cell

Parini Surti,Suresh Kumar Kailasa,Alka Mungray,Tae Jung Park,Arvind Kumar Mungray

DOI: https://doi.org/10.1016/j.fuel.2023.130046

IF: 7.4

2023-10-12

Fuel

Abstract:Microbial fuel cell (MFC) is promoted as an eco-friendly technology for wastewater treatment. However, the use of synthetic polymeric membrane separators raises concerns about the sustainability of MFC, mandating efforts to develop sustainable polymeric membrane with high protonic transfer for MFC assembly. Low-cost and eco-friendly polymer matrix of agar-polyvinyl alcohol (AP) augmented with exfoliated vermiculite nanosheets (Vm NSs) are used to prepare membrane separators for MFC. A simple and facile method for synthesis of AP membrane without and with Vm NSs concentration of 0.25 mg/mL (0.25 Vm), 0.5 mg/mL (0.5 Vm) and 1 mg/mL (1.0 Vm) is adopted in aqueous phase. The proton mass transfer coefficients of prepared membranes (AP, 0.25 Vm, 0.5 Vm and 1.0 Vm) are respectively 94.4, 134.46, 216.26 and 197.69 % higher than commercially available Nafion membrane. These membranes are tested in three different configurations of MFC: aerated cathode, air cathode and anaerobic dye cathode MFC. Highest current densities of 1515 and 949 mA/m 3 are obtained with 1.0 Vm membrane in aerated and air cathode-MFC respectively while Nafion membrane could produce 623 and 405 mA/m 3 . In anaerobic dye cathode MFC, 0.5 Vm membrane is able to achieve the highest current density of 935 mA/m 3 along with 71 % methyl red decolorization while Nafion membrane produced highest current density of 104 mA/m 3 with 59 % decolorization. Vm NSs augmentation enhances the properties of base AP membrane which can be conveniently used as an alternative to expensive Nafion membrane in the desired configuration of MFC.

energy & fuels,engineering, chemical
Modification of clayware ceramic membrane for enhancing the performance of microbial fuel cell

Jain Suransh,Alok Kumar Tiwari,Arvind Kumar Mungray

DOI: https://doi.org/10.1002/ep.13427

2020-05-14

Abstract:The aim of this study was to develop an economically viable clayware ceramic membrane that exhibits proton mass transfer comparable to the commercially available membrane (Nafion 117) for microbial fuel cell (MFC). The clayware ceramic membrane made from red soil was modified using cation exchangers like Montmorillonite (MMT), Vermiculite (VC) and by spray coating of MMT composite with Nafion solution. Nafion‐117 (a commercial membrane) and membrane prepared using only red soil were used as a standard and control respectively. Other membranes include 20% blend of MMT with red soil (SM); 20% VC with red soil (SV); 10% blend of each MMT and VC with red soil (SMV) and SM membrane spray‐coated with Nafion solution (SMN). Addition of cation exchangers enhances the performance of the clayware ceramic membranes as compared to the control and coating of Nafion solution on SMN leads it to perform even better. Average OCV (open circuit voltage) and average OV (operating voltage) for the SMN membranes were 670±17.63 mV, 82±5.69 mV respectively which are best among all the fabricated membranes. The power density of the SMN membrane was 84.3 mW/m3 which is 5 times that of control. The study demonstrates that SMN membrane can be used as an alternate for more costly polymeric membranes in MFC.This article is protected by copyright. All rights reserved.

environmental sciences,green & sustainable science & technology,engineering, environmental, chemical
Highly Ion-Conductive Anion Exchange Membranes with Superior Mechanical Properties Based on Polymeric Ionic Liquid Filled Functionalized Bacterial Cellulose for Alkaline Fuel Cells

Zhanghu Yu,Wen-Chin Tsen,Ting Qu,Fan Cheng,Fuqiang Hu,Hai Liu,Sheng Wen,Chunli Gong

DOI: https://doi.org/10.1016/j.jmrt.2023.02.197

2023-01-01

Abstract:How to simultaneously improve the ionic conductivity and mechanical properties is a key problem facing currently used anion-exchange membranes (AEMs). Here, biomass-based bacterial cellulose (BC) was used as a porous template to make TiO2 localized minerali-zation around the surface of BC nanofibers, and constructed a TiO2-coated BC porous substrate (TiO2@BC) with hierarchical structure. Then, the coated TiO2 nanoparticles was densely grafted by quaternary ammonium groups to obtain high ionic conduction ability. After filling with a polymeric ionic liquid (PIL) with high ion exchange capacity through in situ polymerization and crosslinking, the obtained novel PIL-filled AEM possessed ultrahigh ionic conductivity of 100.5 mS cm -1 at 80 degrees C, which was 72.1% higher than that of the PIL-filled pure BC membrane (only 58.4 mS cm -1). Moreover, by the aid of the synergistic reinforcement effect of TiO2@BC, the membrane exhibited extremely high dry strength of 95.3 MPa and satisfactory wet strength and flexibility. When at fully hydrate state, the membrane with the size of 1 x 4 cm (width x length) can hang a bottle containing 1000 g of water. The single cell equipped with this membrane output the peak power density of 40.2 mW cm -2, showing its great potential as a high-performance biomass-based AEM.(c) 2023 The Authors. Published by Elsevier B.V. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).
Ion Exchange Membrane Cathodes For Scalable Microbial Fuel Cells

YI Z UO,S HAOAN C HENG,BRUCE E. L OGAN

DOI: https://doi.org/10.1021/es801055r

IF: 11.4

2008-01-01

Environmental Science & Technology

Abstract:One of the main challenges for using microbial fuel cells (MFCs) is developing materials and architectures that are economical and generate high power densities. The performance of two cathodes constructed from two low-cost anion (AEM) and cation (CEM) exchange membranes was compared to that achieved using an ultrafiltration (UF) cathode, when the membranes were made electrically conductive using graphite paint and a nonprecious metal catalyst (CoTMPP). The best performance in single-chamber MFCs using graphite fiber brush anodes was achieved using an AEM cathode with the conductive coating facing the solution, at a catalyst loading of 0.5 mg/cm(2) CoTMPP. The maximum power density was 449 mW/m(2) (normalized to the projected cathode surface area) or 13.1 W/m(3) (total reactor volume), with a Coulombic efficiency up to 70% in a 50 mM phosphate buffer solution (PBS) using acetate. Decreasing the CoTMPP loading by 40-80% reduced power by 28-56%, with only 16% of the power (72 mW/m(2)) generated using an AEM cathode lacking a catalyst. Using a current collector (a stainless steel mesh) pressed against the inside surface of the AEM cathode and 200 mM PBS, the maximum power produced was further increased to 728 mW/m(2) (21.2 W/m(3)). The use of AEM cathodes and brush anodes provides comparable performance to similar systems that use materials costing nearly an order of magnitude more (carbon paper electrodes) and thus represent more useful materials for reducing the costs of MFCs for wastewater treatment applications.
A Novel Filtration Composite Anode Configuration of Microbial Fuel Cell for Efficient Wastewater Treatment and Enhanced Power Generation

Ting Xu,Qiuying Wang,Shijia Wu,Boya Fu,Peng Liang,Xia Huang,Xiaoyuan Zhang

DOI: https://doi.org/10.1016/j.jclepro.2017.12.259

IF: 11.1

2018-01-01

Journal of Cleaner Production

Abstract:A microbial fuel cell (MFC), as a cleaner wastewater treatment process, can recover electricity from organic wastes. However, high power production and high quality effluent are difficult to achieve simultaneously. In this study, a novel filtration composite anode (FCA), which combined carbon fiber brush and carbon textile was proposed to enhance COD removal and power generation performance of MFCs. The COD removal rate constant of MFCs with the filtration composite anode (FCA-MFC) was 033 h(-1), much higher than that of MFCs with single brush anode (FB-MFC) (0.23 h(-1)) or textile anode (FT-MFC) (0.18 h(-1)) in the recirculation mode, and also exceeded that of CA-MFC in non-recirculation mode (0.12 h(-1)). FCA-MFC delivered a maximum power density of 1140 mW m(-2) at a recirculation rate of 2 mL min(-1), which was higher than the FB-MFC (990 mW m(-2)) and the FT-MFC (80 mW m(-2)) and its counterparts in non-recirculation mode (1000 mW m(-2)). Moreover, the FCA-MFC maintained a higher current density (4.0 A m(-2)) than the other two MFCs until the COD decreased to 40 mg L-1 at an external resistance of 100 Omega. CV and EIS tests verified a higher electrochemical performance of the filtration composite anode. These results demonstrated higher COD removals and power generation of the composite anode at ambient temperature, resulting from the filtration effect that facilitated mass transfer, increased microbial colonization, and improved electrochemical activity. Considering the high-quality effluent and high power generation, the filtration composite anode configuration promises a great potential for sustainable wastewater treatment application. (C) 2018 Elsevier Ltd. All rights reserved.
Improving MFC efficiency in power generation and COD removal by using protic ionic liquid in MWCNT-CS-2-aminothiazole-SO 3 H nanoparticle-infused sulfonated PES

Pegah Shadman,Alireza Shakeri,Sirus Zinadini

DOI: https://doi.org/10.1016/j.enconman.2023.118049

IF: 10.4

2024-01-10

Energy Conversion and Management

Abstract:This study exhibits a novel nanofiller, functionalized multi-walled carbon nanotube (MWCNT)/chitosan (CS) by 2-aminothiazole/SO 3 H. This synthesized nanofiller was incorporated with a fabricated sulfonated polyethersulfone (SPES) to manufacture a composite proton exchange membrane (PEM), SPES/MWCNT-CS-2-aminothiazole-SO 3 H. The composite membranes were fabricated by different percentage amounts of nanofiller (0.1 wt%, 0.5 wt%, 1.0 wt%, 1.5 wt%). The trait comparison of SPES/MWCNT-CS-2-aminothiazole-SO 3 H, SPES, and Nafion 117 membrane is performed to investigate their application in the microbial fuel cell (MFC). The fabricated composite membrane SPES/MWCNT-CS-2-aminothiazole-SO 3 H 0.5 wt% illustrated superior water uptake (WU) of 90.41 %. Moreover, the maximum power density (PD) (66.04 mW.m −2 ) was produced by SPES/MWCNT-CS-2-aminothiazole-SO 3 H 0.5 wt%, which demonstrated a considerable increase (approximately 20 times) compared to SPES (3.19 mW.m −2 ). Furthermore, the power density generated by the Nafion 117 membrane was 15.78 mW.m −2 . In addition, the statistics in MFC usage presented that prepared composite membrane combined with MWCNT-CS-2-aminothiazole-SO 3 H 0.5 wt% had the optimum chemical oxygen demand (COD) removal, and the coulombic efficiency (CE), with 90.46 % and 80.68 %, respectively. Due to the high efficiency and remarkable power generation achieved by the MFC with SPES/MWCNT-CS-2-aminothiazole-SO 3 H 0.5 wt%, this modified membrane can be considered as a promising cost-effective alternative separator in MFC.

energy & fuels,thermodynamics,mechanics
Using A Glass Fiber Separator in A Single-Chamber Air-Cathode Microbial Fuel Cell Shortens Start-Up Time and Improves Anode Performance at Ambient and Mesophilic Temperatures

Xiaoyuan Zhang,Peng Liang,Juan Shi,Jincheng Wei,Xia Huang

DOI: https://doi.org/10.1016/j.biortech.2012.12.091

IF: 11.4

2013-01-01

Bioresource Technology

Abstract:A shorter start-up time and highly negative anode potentials are needed to improve single-chamber air-cathode microbial fuel cells (MFCs). Using a glass fiber separator reduced the start-up time from 10d to 8d at 20°C, and from 4d to 2d at 30°C, and enhanced coulombic efficiency (CE) from <60% to 89% (20°C) and 87% (30°C). Separators also reduced anode potentials by 20-190mV, charge transfer resistances by 76% (20°C) and 19% (30°C), and increased CV peak currents by 24% (20°C) and 8% (30°C) and the potential range for redox activity (-0.55 to 0.10mV vs. -0.49 to -0.24mV at 20°C). Using a glass fiber separator in an air-cathode MFC, combined with inoculation at a mesophilic temperature, are excellent strategies to shorten start-up time and to enhance anode performance and CE.
Goethite supplemented natural clay ceramic as an alternative proton exchange membrane and its application in microbial fuel cell

Indrasis Das,Sovik Das,Rohan Dixit,M. M. Ghangrekar

DOI: https://doi.org/10.1007/s11581-020-03472-1

IF: 2.961

2020-02-06

Ionics

Abstract:Microbial fuel cell (MFC) is a bioelectrochemical system, which treats wastewater with simultaneous recovery of bioelectricity. Costly proton exchange membrane, like Nafion-117, brings a serious bottleneck towards the sustainable scaled-up application of this technology. For an appropriate field-scale demonstration of MFC, the fabrication cost needs to be reduced drastically. This can be achieved by using low-cost proton exchange membrane (PEM) in MFCs, which would demonstrate equivalent performance as commercially available expensive PEMs. Such a novel PEM constituting 5% goethite and natural clay as a base material was synthesized, named as G-5, and it was used in MFC as a separator. This G-5 membrane was estimated to be five folds cheaper than the commercially available Nafion-117 membrane, which is popularly used in MFC. Membrane properties, like water and acetate uptake, and proton conductivity of the G-5 membrane, were evaluated and compared with Nafion-117. A power density obtained from the MFC using G-5 as PEM (112.81 ± 8.74 mW/m2) was slightly higher than the MFC with Nafion-117 as PEM (106.95 ± 5.52 mW/m2). Chemical oxygen demand removal and Coulombic efficiency for MFC with G-5 membrane were found to be 22% and 8.6% higher, respectively, in comparison with that of the MFC with Nafion-117 as PEM. Thus, low-cost G-5 membrane demonstrated the potential to be used for scaling-up of MFCs to reduce fabrication cost for successful field-scale implementation of MFCs.

chemistry, physical,physics, condensed matter,electrochemistry
Cathodic Biofouling Control by Microbial Separators in Air-Breathing Microbial Fuel Cells

Chao Li,Kexin Yi,Shaogang Hu,Wulin Yang

DOI: https://doi.org/10.1016/j.ese.2023.100251

IF: 9.371

2023-01-01

Environmental Science and Ecotechnology

Abstract:Microbial fuel cells (MFCs) incorporating air-breathing cathodes have emerged as a promising ecofriendly wastewater treatment technology capable of operating on an energy-free basis. However, the inevitable biofouling of these devices rapidly decreases cathodic catalytic activity and also reduces the stability of MFCs during long-term operation. The present work developed a novel microbial separator for use in air-breathing MFCs that protects cathodic catalytic activity. In these modified devices, microbes preferentially grow on the microbial separator rather than the cathodic surface such that biofouling is prevented. Trials showed that this concept provided low charge transfer and mass diffusion resistance values during the cathodic oxygen reduction reaction of 4.6 +/- 1.3 and 17.3 +/- 6.8 U, respectively, after prolonged operation. The maximum power density was found to be stable at 1.06 +/- 0.07 W m-2 throughout a long-term test and the chemical oxygen demand removal efficiency was increased to 92% compared with a value of 83% for MFCs exhibiting serious biofouling. In addition, a cathode combined with a microbial separator demonstrated less cross-cathode diffusion of oxygen to the anolyte. This effect indirectly induced the growth of electroactive bacteria and produced higher currents in air-breathing MFCs. Most importantly, the present microbial separator concept enhances both the lifespan and economics of air-breathing MFCs by removing the need to replace or regenerate the cathode during longterm operation. These results indicate that the installation of a microbial separator is an effective means of stabilizing power generation and ensuring the cost-effective performance of air-breathing MFCs intended for future industrial applications.(c) 2023 The Authors. Published by Elsevier B.V. on behalf of Chinese Society for Environmental Sciences, Harbin Institute of Technology, Chinese Research Academy of Environmental Sciences. This is an open access article under the CC BY-NC-ND license (http://creativecommons.org/licenses/by-nc-nd/4.0/).

Solution design for Low Fluorine Trifluoroacetate route to YBa 2 Cu 3 O 7 1 films 2 3

Separator Characteristics for Increasing Performance of Microbial Fuel Cells

Recent advances in the separators for microbial fuel cells.

A Comprehensive Study of Custom-Made Ceramic Separators for Microbial Fuel Cells: Towards “Living” Bricks

Characterization and application of novel fly ash blended ceramic membrane in MFC for low-cost and sustainable wastewater treatment and power generation

Tubular ceramic performance as separator for microbial fuel cell: A review

Development of a Novel Composite Polymer Electrolyte Membrane for Application as a Separator in a Dual Chamber Microbial Fuel Cell

Mitigating External and Internal Cathode Fouling Using a Polymer Bonded Separator in Microbial Fuel Cells.

Unlaminated Carbon As Separator In Air-Cathode Single-Chamber Microbial Fuel Cells

The use of nylon and glass fiber filter separators with different pore sizes in air-cathode single-chamber microbial fuel cells

An Expanded Clay-Coated Separator with Unique Microporous Structure for Enhancing Electrochemical Performance of Rechargeable Hybrid Aqueous Batteries

Poly(vinyl alcohol) separators improve the coulombic efficiency of activated carbon cathodes in microbial fuel cells

Vermiculite nanosheet augmented novel proton exchange membrane for microbial fuel cell

Modification of clayware ceramic membrane for enhancing the performance of microbial fuel cell

Highly Ion-Conductive Anion Exchange Membranes with Superior Mechanical Properties Based on Polymeric Ionic Liquid Filled Functionalized Bacterial Cellulose for Alkaline Fuel Cells

Ion Exchange Membrane Cathodes For Scalable Microbial Fuel Cells

A Novel Filtration Composite Anode Configuration of Microbial Fuel Cell for Efficient Wastewater Treatment and Enhanced Power Generation

Improving MFC efficiency in power generation and COD removal by using protic ionic liquid in MWCNT-CS-2-aminothiazole-SO 3 H nanoparticle-infused sulfonated PES

Using A Glass Fiber Separator in A Single-Chamber Air-Cathode Microbial Fuel Cell Shortens Start-Up Time and Improves Anode Performance at Ambient and Mesophilic Temperatures

Goethite supplemented natural clay ceramic as an alternative proton exchange membrane and its application in microbial fuel cell

Cathodic Biofouling Control by Microbial Separators in Air-Breathing Microbial Fuel Cells