Abstract:Nano composites have been utilized increasingly because of their high strength, stiffness, toughness, and through-thickness properties. The incorporation of carbon nano fibers with a high aspect ratio and extremely large surface area into glass/epoxy polymer composites improve their tensile and compression properties significantly. Although a number of efforts have been made to improve various properties by mixing nano particles directly into resin, however, it could lead to high viscosities which create problems during processing. In this particular study, an attempt has been made to investigate tensile and compression behavior of nano composites by using, state of the art, a different technique i.e spraying the Carbon Nano Fibers (CNF) on dry woven glass pre-form before infusion. The nano composite samples were prepared using a spraying methodology i.e dispersing the 2.0 weight percent CNF solution on glass fabric, and evaporating the solvent such that only nano fibers remain on perform, followed by Vacuum Assisted Resin Transfer Molding (VARTM). Tensile and compression tests were performed to evaluate the effectiveness and behavior of CNF addition on these mechanical properties. Results indicated simultaneous improvement in tensile and compression properties by incorporating a very small amount of carbon nano fibers into the matrix system. 18-21 percent improvement in tensile strength and 6-9 percent in compressive strength, with respect to the neat composite. The rise in their modulus has also been discussed in detail and part of this study. For in-depth analysis, microscopic approaches were also carried out to investigate the fracture behavior and mechanism of material. Scanning electron microscopy of fractured surfaces revealed improved primary fiber matrix adhesion and indications of CNF-induced matrix toughening due to the presence of CNFs. SEM evaluation also revealed relatively less damage in the tested fracture surfaces of the nano phased composites in terms of matrix failure, fiber breakage, matrix fiber de-bonding, and de-lamination, compared to the neat system.

Localization of carbon nanotubes in resin rich zones of a woven composite linked to the dispersion state

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Single Carbon Fiber/Acid-Treated CNT-Epoxy Composites by Electro- Micromechanical Technique and Wettability Test for Dispersion and Self-Sensing

Effectiveness of short and straight carbon nanotubes on dispersion state and static/dynamic mechanical properties of woven glass fibre-reinforced polymer laminates

Mapping local microstructure and mechanical performance around carbon nanotube grafted silica fibres: methodologies for hierarchical composites

Effect of Dispersion Method on Tribological Properties of Carbon Nanotube Reinforced Epoxy Resin Composites

Effects of dispersing methods on the properties of low content carbon nanotubes-glass fiber/epoxy reisn laminates

Distribution and Integrity of Carbon Nanotubes in Carbon Nanotube/Magnesium Composites

Study on Mechanical Properties of Carbon Nanotube Reinforced Composites

Tensile and compression behavior of woven glass/epoxy nano composites based on spraying methodology

Mechanical Properties of Carbon Nanotube Fibers Reinforced Epoxy Resin Composite Films Prepared by Wet Winding

Carbon nanotube reinforced fiber / epoxy multi-scale hybrid composites via electrophoretic deposition : processing , characterization and multifunctional properties

Carbon fiber/epoxy composite property enhancement through incorporation of carbon nanotubes at the fiber-matrix interphase – Part II: Mechanical and electrical properties of carbon nanotube coated carbon fiber composites

A multi-layer resin film infusion process to control CNTs distribution and alignment for improving CFRP interlaminar fracture toughness

Effects of CNT Microstructural Characteristics on the Interfacial Enhancement Mechanism of Carbon Fiber Reinforced Epoxy Composites Via Molecular Dynamics Simulations

High-strength composite fibers: realizing true potential of carbon nanotubes in polymer matrix through continuous reticulate architecture and molecular level couplings.

Effect of CNT-Based Resin Modification on the Mechanical Properties of Polymer Composites

Influence of a Liquid-Like MWCNT Reinforcement on Interfacial and Mechanical Properties of Carbon Fiber Filament Winding Composites

Microstructures and Tensile Behavior of Carbon Nanotubes Reinforced Cu Matrix Composites with Molecular-Level Dispersion

The Properties of Dry-Spun Carbon Nanotube Fibers and Their Interfacial Shear Strength in an Epoxy Composite

Carbon Nanotube/Epoxy Composites Fabricated by Resin Transfer Molding