Abstract:Stainless steels are increasingly used in construction today, especially in harsh environments, in which steel corrosion commonly occurs. Cold-formed stainless steel structures are currently increasing in popularity because of its efficiency in load-bearing capacity and its appealing architectural appearance. Cold-rolling and press-braking are the cold-working processes used in the forming of stainless steel sections. Press braking can produce large cross-sections from thin to thick-walled sections compared to cold-rolling. Cold-forming in press-braked sections significantly affect member behaviour and joints; therefore, they have attained great attention from many researchers to initiate investigations on those effects. This paper examines the behaviour of residual stress distribution of stainless steel press-braked sections by implementing three-dimensional finite element (3D-FE) technique. The study proposed a full finite element procedure to predict the residual stresses starting from coiling-uncoiling to press-braking. This work considered material anisotropy to examine its effect on the residual stress distribution. The technique adopted was compared with different finite element techniques in the literature. This study also provided a parametric study for three corner radius-to-thickness ratios looking at the through-thickness residual stress distribution of four stainless steels (i.e., ferritic, austenitic, duplex, lean duplex) in which have their own chemical composition. In conclusion, the comparison showed that the adopted technique provides a detailed prediction of residual stress distribution. The influence of geometrical aspects is more pronounced than the material properties. Neglecting the material anisotropy shows higher shifting in the neutral axis. The parametric study showed that all stainless steel types have the same stress through-thickness distribution. Moreover, R/t ratios' effect is insignificant in all transverse residual stress distributions, but a slight change to R/t ratios can affect the longitudinal residual stress distribution.

Numerical Prediction of Residual Stresses Distribution in Thin-Walled Press-Braked Stainless Steel Sections

An investigation on longitudinal residual strains distribution of thin-walled press-braked cold formed steel sections using 3D FEM technique

A Method for Prediction of Forming Strain for Cold Stamping Formed Head Made of S30408 Austenitic Stainless Steel

Numerical Study on Residual Stresses and Plastic Strains in Cold-Formed High-Strength Steel Circular Hollow Sections

Prediction of Residual Stress Distributions in Welded Sections of P92 Pipes with Small Diameter and Thick Wall Based on 3D Finite Element Simulation

Residual Stress Distributions in Welded Stainless Steel Sections

Finite element analysis, prediction, and optimization of residual stresses in multi-pass arc welding with experimental evaluation

Prediction of residual stress after cold rolling and coiling processes

Finite Element Analysis of Modeling Residual Stress Distribution in All-position Duplex Stainless Steel Welded Pipe

3D Numerical Simulation of Brazed Residual Stress in Stainless Steel Plate-Fin Structure

NUMERICAL SIMULATION OF RESIDUAL STRESS IN COLD-FORMED SIGMA BEAMS

Residual Stress Tests and Predictive Model of Friction Stir Welded Normal-Strength Aluminium Alloy H-shaped Sections

Measurement and distribution models of residual stresses in welded stainless steel box sections

Prediction of Residual Stresses Within Dissimilar Al/steel Friction Stir Lap Welds Using an Eulerian-based Modeling Approach

Numerical analysis of stress & strain and thickness variation in single point incremental forming of tailor welded steel blanks

Experimental and numerical evaluations of the distribution and effect of roll-forming residual stress on CFS sigma beams

RESIDUAL STRESS OF WELDED I SECTIONS FABRICATED FROM HIGH PERFORMANCE STEEL: EXPERIMENTAL INVESTIGATION AND MODELLING

Numerical Simulation to Study the Effect of Repair Width on Residual Stresses of a Stainless Steel Clad Plate

Effect of Residual Stresses on the Fatigue Stress Range of a Pre-Deformed Stainless Steel AISI 316L Exposed to Combined Loading

3D numerical modelling of residual stresses induced by reaming

Prediction of stress distribution in press-fit process of interference fit with a new theoretical model