Memory-Mapped Architectures

K. Vadaparty

Abstract:

What problem does this paper attempt to address?

Mass-selective removal of ions from Paul traps using parametric excitation

Julian Schmidt,Daniel Hönig,Pascal Weckesser,Fabian Thielemann,Tobias Schaetz,Leon Karpa

DOI: https://doi.org/10.1007/s00340-020-07491-8

2020-10-09

Applied Physics B

Abstract:Abstract We study a method for mass-selective removal of ions from a Paul trap by parametric excitation. This can be achieved by applying an oscillating electric quadrupole field at twice the secular frequency $$\omega _{\text {sec}}$$ ω sec using pairs of opposing electrodes. While excitation near the resonance with the secular frequency $$\omega _{\text {sec}}$$ ω sec only leads to a linear increase of the amplitude with excitation duration, parametric excitation near $$2\, \omega _{\text {sec}}$$ 2 ω sec results in an exponential increase of the amplitude. This enables efficient removal of ions from the trap with modest excitation voltages and narrow bandwidth, therefore, substantially reducing the disturbance of ions with other charge-to-mass ratios. We numerically study and compare the mass selectivity of the two methods. In addition, we experimentally show that the barium isotopes with 136 and 137 nucleons can be removed from small ion crystals and ejected out of the trap while keeping $$^{138}\text {Ba}^{+}$$ 138 Ba + ions Doppler cooled, corresponding to a mass selectivity of better than $$\Delta m / m = 1/138$$ Δ m / m = 1 / 138 . This method can be widely applied to ion trapping experiments without major modifications since it only requires modulating the potential of the ion trap.

optics,physics, applied
Possibility of operating quadrupole mass filter at high resolution

Mikhail Sudakov,Eugenij Mamontov,Fuxing Xu,Chongsheng Xu,Chuan-Fan Ding

DOI: https://doi.org/10.1016/j.ijms.2016.09.003

IF: 1.934

2016-01-01

International Journal of Mass Spectrometry

Abstract:⿢Faster mass separation is obtained with the use of stability islands of special shape (Xband) formed by two AC excitations. Only few cycles of the base AC excitation frequency ν is sufficient to eject unstable ions and it possible to obtain about 10000 mass resolution with ion residence time of only 100 RF cycles.⿢Mass separation of ions happens in only one direction which increases acceptance of the mass filter.⿢The instability bands which are used for mass separation appear only in the vicinity of the upper tip of the first stability region, so it possible to use the delayed DC ramp technique to improve signal sensitivity.⿢The operation with the use of additional AC excitations is not sensitive to many nonlinear field distortions. So the new method might be applied to quadrupole analyzers with lower mechanical accuracy for improving their mass resolving power.
Mass Peak Shape Improvement of A Quadrupole Mass Filter when Operating with A Rectangular Wave Power Supply

Chan Luo,Dan Jiang,Chuan-Fan Ding,Nikolai V. Konenkov

DOI: https://doi.org/10.1002/rcm.4186

2009-01-01

Abstract:Numeric experiments were performed to study the first and second stability regions and find the optimal configurations of a quadrupole mass filter constructed of circular quadrupole rods with a rectangular wave power supply. The ion transmission contours were calculated using ion trajectory simulations. For the first stability region, the optimal rod set configuration and the ratio r/r(0) is 1.110-1.115; for the second stability region, it is 1.128-1.130. Low-frequency direct current (DC) modulation with the parameters of m = 0.04-0.16 and nu = omega/Omega = 1/8-1/14 improves the mass peak shape of the circular rod quadrupole mass filter at the optimal r/r(0) ratio of 1.130. The amplitude modulation does not improve mass peak shape. Copyright (C) 2009 John Wiley & Sons, Ltd.
Two stability islands of quadrupole mass filter near q = 0.9 created by auxiliary radio frequency voltage.

Chan Luo,Gongyu Jiang,Nikolai V Konenkov,Chuanfan Ding

DOI: https://doi.org/10.1255/ejms.1037

2009-01-01

European Journal of Mass Spectrometry

Abstract:We report the numerical investigations of quadrupole mass filters concerning stability islands created by auxiliary radio frequency (RF) voltage with high and low frequencies near q=0.9. The islands are located along the q axis near boundary value q=0 908 with a low a parameter. The analysis is based upon the matrix method for stability diagram calculations and ion trajectory numerical simulation The trajectory of ion motions is generated using Runge-Kutta-Nystrom-Dormand-Prince (RK-N-DP) order integration The ion source model with Gaussian distribution of initial positions and transverse velocities is used. In RF-only operation mode, a resolution power of about R-01=600 without peak tails is achieved with a separation time of about 50 RF cycles. Relatively high resolution power of about 2000-3000 is observed in DC+RF separation mode with a low frequency auxiliary RF signal. The boundaries of stability diagram for additional RF voltage with high frequency are strongly diffused until the separation time is increased up to n=300 RF cycles The strong influence of phase shifts between main drive RF voltage and small auxiliary RF voltage on transmission is also examined In DC+RF mode, the period of transmission varies with phase shift of pi or one period of the main drive RF vottage: and in RF-only mode this period is pi/2.
An Ultra Broadband Passive Vector Modulator Phase Shifter

Haotian Wu,Yunqing Hu,Luna Ye,Qin Zheng,Liping Liu,Wei Chen,Xu Ding,Hua Chen,Faxin Yu

DOI: https://doi.org/10.1587/elex.21.20240331

2024-01-01

IEICE Electronics Express

Abstract:This letter presents an ultra-broadband passive vector modulator phase shifter applied to a 4-element tranceiver. A compact cascaded three-stage differential coupler with anti-jamming connective mode and orthogonal placement method is presented, which amalgamates the through-path and coupled-path signal to reduce the phase and magnitude error of the wideband I/Q generator. A magnetic coupling enhanced lattice power synthesizer is proposed, which synthesizes I/Q signals for the accurate wideband target phase interpolation. The proposed phase shifter occupies an extraordinary compact chip area (1.6mm-by-0.6mm) in 0.13 mu m CMOS process. Measurement results demonstrates that the proposed phase shifter achieves high precision with maximum RMS phase and magnitude error 3.5 degrees and 0.82dB, respectively, in the range of 3-16GHz. In addition, simulated IP1dB is as high as +19dBm with no power consumption.
Simulation Study of a Planar Quadrupole Mass Filter for MEMS Mass Spectrometer

Yu-Peng CHENG,Chen SHEN,Zhang-Xu WU,Shan LI,You-Jiang LIU,Han WANG,Chi-Lai CHEN

DOI: https://doi.org/10.1016/j.cjac.2024.100364

IF: 1.193

2024-01-28

Chinese Journal of Analytical Chemistry

Abstract:Micro-electro-mechanical system (MEMS) based mass spectrometry, MEMS mass spectrometry, emerges a new technique branch of miniature mass spectrometry. One of the main challenges hindering the development of MEMS mass spectrometry is the poor compatibility between the complex electrode structure of traditional ion optics and MEMS processes. This paper proposed a planar quadrupole mass filter utilizing a highly simplified stacked-layer structure and film electrodes, which is easy to fabricate with high precision by MEMS surface micromachining. The ion trajectory simulation model of the MEMS mass spectrometry chip involving all necessary ion optics was elaborated for investigating the preliminary performance of the planar quadrupole mass filter. By optimizing the crucial parameters such as the frequency of radio frequency voltage, the ratio of direct current voltage and radio frequency voltage, pre-pole length, main-pole length, and injection kinetic energy, the preliminary simulation result of planar quadrupole mass filter achieved a 1∼2Da peak width (at 50% of peak height) and 20∼80% ion transmission efficiency. Importantly, the planar quadrupole mass filter demonstrated a maximum working pressure of 0.1 Pa (using air as the buffer gas), 100 times higher than that of conventional quadrupole mass filters, while maintaining a 0.7∼1.8 Da peak width and ∼5% ion transmission efficiency. Additionally, to modify the theoretical formulas for the non-ideal quadrupolar field of planar quadrupole mass filter, a novel approach based on stability diagrams obtained by simulation was also introduced. The pretty good linearity (R 2 =1) between ion masses in the range of 10 to 100Da and the corresponding radio frequency voltages was verified through the simulated mass spectra. Notably, the proportional coefficient of ion mass and radio frequency voltage exhibited a minimal 4% deviation between the simulated value (4.7132 V 0P /Da) and the calculated value (4.9036 V 0P /Da) through the modified formula. In conclusion, the preliminary simulation results demonstrated that the planar quadrupole mass filter possessed moderate performance, high-pressure tolerance, and excellent theoretical consistency, which proved it a promising technology of MEMS mass spectrometry. It can find applications in the fields of gas detection, including the rapid response to hazardous gas emissions and in situ detection of dissolved gases in the deep sea.

chemistry, analytical
Tandem RF-only quadrupole mass filter with quadrupolar excitation

Gongyu Jiang,Chan Luo,N.V. Konenkov,Chuan-Fan Ding

DOI: https://doi.org/10.1016/j.ijms.2009.07.001

IF: 1.934

2009-01-01

International Journal of Mass Spectrometry

Abstract:A powerful instability band located near β=ν=1/10 is created with auxiliary low frequency quadrupole excitations to filter low q ions.
Mass Selection of Ions from Beams Using Waveform Isolation in Radiofrequency Quadrupoles

Qingyu Song,Scott A. Smith,Liang Gao,Wei Xu,Michael Volny,Zheng Ouyang,R. Graham Cooks

DOI: https://doi.org/10.1021/ac802213p

IF: 7.4

2009-01-01

Analytical Chemistry

Abstract:A waveform isolation method is described for the massselective transmission of ions through quadrupole mass filters, and it is implemented on a new tandem mass analyzer instrument. The method features the application of broad-band waveforms comprising appropriate frequencies to cause mass-selective instability in ions of particular mass-to-charge (m/z) and to transmit all others. The experiment is implemented in a tandem quadrupole system in which the first mass filter is a rectilinear ion trap (RIT) operated in a continuous mass-selective mode to transmit ions of ions of one or more arbitrarily selected m/z value(s). The second analyzer was used to verify the quality of the mass selection achieved using the first analyzer via conventional quadrupole ion trap massselective instability scanning. A new subtype of product ion tandem mass spectrometry (MS/MS) scan, termed the summed product ion scan, is demonstrated with a mixture of biological compounds. It is used to characterize product ions arising after simultaneous isolation and collisional activation of multiple precursor species, in this case ions of the same analyte generated in different charge states. The summed product ion scan can be useful for enhancing sensitivity for the analyte of interest or for providing more comprehensive information about an analyte than is available by monitoring a single ionized form of the analyte. The analytical performance of the waveform isolation method is tested using simple drug mixtures, and its potential for increasing overall yields in preparative mass spectrometry is explored briefly. It is shown that efficiencies of ca. 70% of ion transfer to a surface for ion soft landing surface can be achieved. The upper mass range is limited by axial acceleration arising from the stretched geometry, and one solution to this problem is provided.
Dipole and quadrupole resonance excitation in linear quadrupoles

N V Konenkov

DOI: https://doi.org/10.1177/14690667231204359

Abstract:In the development of commercial quadrupole mass spectrometers, there is an interest in improving the performance characteristics such as transmission, resolution, and mass range. In particular, parametric and dipolar resonance excitation of trapping ions are used for linear quadrupole mass filters. Theoretical methods and numerical simulation of ion trajectories were applied for study of ion-optical properties. The review is devoted to description of different excitation methods to improve QMF performance and consists of three parts. The first part presents the results of a linear ion trap simulation for various operating conditions and excitation methods. The second part considers the effects of dipole excitation (DE) on the performance of the quadrupole mass filter. The last part analyzes the formation of stability islands by different methods of quadrupole excitation. To date conditions of mass separation in quadrupole mass filters with sin wave supply were described for stability islands of the first and third stability regions formed by quadrupole and DE. By complicating the electronics such methods allow to overcome the destructive influence of electric field distortions and obtain a resolving power and ion transmission efficiency comparable with commercial devices. At quadrupole resonance excitation by a two-frequency signal, it is possible to reduce the length of electrodes three times without losses in resolution and transmission, which reduces the cost of rod set production with micrometer accuracy. Dipole resonance excitation allows controlling the shape of the mass peak by changing amplitude and phase of the auxiliary AC signal. The main factors affecting the resolving power of a linear ion trap are described theoretically. The numerical modeling results are confirmed by experiment.
Simulation of a Quadrupole Mass Filter with Octupole Field

P. V. Bugrov,A. A. Sysoev,N. V. Konenkov

DOI: https://doi.org/10.1134/s1061934823130038

IF: 1.237

2024-02-01

Journal of Analytical Chemistry

Abstract:This study investigates the transmission contour (shape of the mass peak) through the numerical simulation of ion trajectories in a quadrupole field with small spatial harmonics. The impact of the octupole component on the field is examined, demonstrating a possibility of achieving a resolving power of 5000 with a 2% octupole component and a negative constant component on a pair of electrodes of a smaller radius. A stability diagram near the working apex is significantly affected by the octupole field. The data from the previous experiment qualitatively validated the simulation results.

chemistry, analytical
Simulation study of digital waveform‐driven quadrupole mass filter operated in higher stability regions for high‐resolution inductively coupled plasma mass spectrometry

Rui Hu,Alexander Gundlach‐Graham

DOI: https://doi.org/10.1002/rcm.9753

IF: 2.586

2024-04-14

Rapid Communications in Mass Spectrometry

Abstract:Rationale The use of a frequency‐scanned digital quadrupole mass filter (QMF) with varying duty cycles shows promise for application as a high‐resolution mass analyzer design for inductively coupled plasma mass spectrometry (ICP‐MS). High resolution in ICP‐MS is important to overcome isobaric polyatomic interferences. Here, we explore the possibility and the characteristics of using a digital quadrupole operating in higher stability regions for ICP‐MS. Methods We perform computational simulations in SIMION of a digital QMF that is operated by scanning the frequency of the digital waveform at a fixed driving voltage and various duty cycles. For ions in the atomic mass range (7–238 m / z ), we investigate the expected resolution, transmission, fringe field effects, and ion trajectories. We compare different characteristics between sine and digital waveform QMF. Results Within the capability of current digital waveform generation technology, a digital QMF can produce variable mass resolution, from several hundred to more than 10 000. This mass resolution covers the low, medium, and high resolutions that are typical for sector‐field ICP‐MS. Additionally, simulations suggest that transmission of the QMF remains high at high resolution. For example, with 87.50/12.50 duty cycle (zone 4,1), resolution at 10% peak width is 10 420 for m / z 80. The transmission through the quadrupole, which is constant for all isoenergetic ions, is ~2.5%, and most ion loss is due to the defocusing effects of the fringe field. Compared to sinusoidal QMFs, ions need many fewer cycles in the digital QMF to obtain high resolution. Conclusion The results demonstrate that the use of a frequency‐scanned, duty‐cycle‐modulated digital QMF as the mass analyzer for ICP‐MS has the potential to produce high resolution while maintaining considerable transmission, thus overcoming most spectral interferences in elemental MS.

spectroscopy,biochemical research methods,chemistry, analytical
Square Parametric Excitation: A Digital Resonant Method for the Quadrupole Ion Trap

Grace O Capek,Casey J Howdieshell,Etienne Garand

DOI: https://doi.org/10.1021/jasms.4c00169

2024-08-07

Abstract:Digital ion trap technology is an alternate method for driving quadrupole ion traps and mass filters using variable frequency, fixed amplitude RF square waves in place of variable amplitude, fixed frequency RF sine waves. This technique offers some advantages such as an increase in the high mass analysis range by varying frequency and lower overall voltage requirements. Here, we present a complex square waveform developed for resonant parametric excitation in a quadrupole linear ion trap. Unlike traditional resonance methods, the driving RF square wave and auxiliary square wave are coupled using the same digital circuitry without the need for transformer coupling. In this work, we use this complex waveform to selectively excite the first order parametric resonances of ion motion. The square parametric excitation method presented here employs a simple and repetitive circuit design consisting of a low-voltage waveform generator followed by a series of high-voltage MOSFET switches. This design allows for resonance methods to be easily implemented in the all-digital quadrupole. The complex square waveform can perform the same useful functions as sine wave auxiliary signals, such as selective mass elimination and mass isolation. We also demonstrate that the mass resolution performance and S/N of our digital mass spectrometer is improved by applying the complex square waveform during ion ejection.
Increasing Isolation Efficiency Using a Segmented Quadrupole Mass Filter Operated with Rectangular Waveforms

Robert L. Schrader,Gordon A. Anderson,David H. Russell

DOI: https://doi.org/10.1021/jasms.4c00051

IF: 3.262

2024-05-01

Journal of the American Society for Mass Spectrometry

Abstract:The performance of a segmented quadrupole mass filter operated with rectangular waveforms and capacitively coupled rectangular waveforms applied to the prefilters was examined on a home-built quadrupole-Orbitrap platform. For peak widths of 50 m/z, 100% isolation efficiency was achieved, which fell to approximately 20% for 5 m/z peak width for a rectangular waveform of 150 V(0-p). Due to a small exit aperture following the mass filter, peak structure was observed in both experimental peak shapes...

chemistry, physical,spectroscopy, analytical,biochemical research methods
A Strategy for Simultaneously Improving Resolution and Sensitivity of Hybrid Quadrupole Ion Trap/Time-of-Flight Mass Spectrometry Using Square Waveform Phase Modulation

Yixue Cao,Ping Chen,Lei Hua,Weiguo Wang,Yi Chen,Yuxuan Wen,Yuanyuan Xie,Haiyang Li

DOI: https://doi.org/10.1021/jasms.1c00314

IF: 3.262

2021-12-30

Journal of the American Society for Mass Spectrometry

Abstract:The hybrid quadrupole ion trap/time-of-flight mass spectrometry (QIT/TOFMS) device is popular because of its advantages of high sensitivity, high resolution, and MS/MS capability. However, the analytical performance of QIT/TOFMS is severely limited by the parameters of the ion trap, as QIT is typically used as a TOF pulser because the ion initial distributions of space, velocity, and angle change dynamically with the phase angle of rf voltage. In this work, a square waveform phase modulation strategy was proposed to eliminate the influence of the rf phase angle, and the dependence of QIT/TOFMS performance on the phase angle was studied. It was found that the mass resolution and signal intensity showed a "W" trend with the increase of the ion extraction phase angle from 0° to 360°, where the best resolution and sensitivity were obtained at 0°, 180°, and 360° while the worst resolution and sensitivity were obtained at 90° and 270°. Moreover, the optimum phase angle was independent of m/z. As a result, the mass resolution for m/z 106, 164, and 258 was improved by 162%, 160%, and 210% respectively, while the signal intensities for m/z 106, 164, and 258 were enhanced by 25 ± 1, 10 ± 1, and 21 ± 1 fold, respectively, and a limit of detection down to 0.015 ppbv for m/z 164 was obtained. The experiment results indicated that the square waveform phase modulation strategy could be used to simultaneously improve the resolution and sensitivity of QIT/TOFMS.

chemistry, physical,spectroscopy, analytical,biochemical research methods
Quadrupole mass filters with octopole fields.

Chuanfan Ding,N V Konenkov,D J Douglas

DOI: https://doi.org/10.1002/rcm.1235

IF: 2.586

2003-01-01

Rapid Communications in Mass Spectrometry

Abstract:The performance of quadrupole mass filters with added octopole fields in the range 2.0-4.0% has been investigated. The added fields are much greater than those normally added to conventional rod sets by mechanical tolerances or construction errors. Quadrupole rod sets with added octopole fields were constructed with round rods by making one pair of rods greater in diameter than the other pair. For positive ions, resolution at half height of only about 200 is possible if the negative direct current (dc) output of the quadrupole power supply is connected to the smaller rods. If the positive dc output of the quadrupole power supply is connected to the smaller rods, the resolution improves dramatically; a resolution at half height of 5800 has been observed with a rod set with 2.6% added octopole field. For negative ions the best resolution is obtained with the polarity of the dc reversed, i.e. with the negative dc applied to the smaller rods. These findings are unexpected in view of the literature that argues that to obtain high mass resolution with quadrupole mass filters, higher order multipoles must be kept as small as possible. Numerical simulations of peak shapes agree qualitatively with experiments. Simulation of the boundaries of the first stability region for positive ions shows that when the positive dc is applied to the smaller rods, the addition of a 2.0% octopole field causes the boundaries to shift slightly but the boundaries are well defined, and the tip of the stability region remains sharp. When the positive dc is applied to the larger rods, the boundaries of the stability region move out and become diffuse. For instruments that require a rod set that can be used both as a linear trap and a mass filter, these rod sets may offer improved trap performance while still being capable of providing conventional mass analysis. Copyright (C) 2003 John Wiley Sons, Ltd.
Field tuning and rf measurements of the four-vane radio frequency quadrupole with ramped inter-vane voltage

Q. Z. Xing,X. L. Guan,Q. K. Guo,Y. Li,X. W. Wang,K. Liu,Z. M. Wang,S. X. Zheng,C. Zhao,X. D. Yu,Y. Lei,S. Wang,P. F. Ma,B. C. Wang

DOI: https://doi.org/10.1103/physrevaccelbeams.22.020102

2019-01-01

Physical Review Accelerators and Beams

Abstract:This paper describes the physical design, rf measurement, and tuning result of a 325 MHz four-vane radio frequency quadrupole (RFQ) with a ramped inter-vane voltage. The 3-meter-long RFQ will accelerate the negative hydrogen ion beam from 50 keV to 3 MeV with a peak current of 5 mA, a pulse width of 10-40 mu s, and a maximum repetition rate of 0.5 Hz. During tuning we reveal that the coupling loop of the coaxial coupler adopted for this RFQ enhances the interference between the dipole field distribution and the coupling coefficient. Therefore, an iteration method is adopted to simultaneously achieve the desired field distribution and coupling coefficient. After tuning, the relative error between the measured field distribution and the designed curve for the operating quadrupole mode is within +/- 2.7%, and the dipole components are about +/- 1.9% of the quadrupole mode. The measured coupling coefficient of the rf power coupler equals 1.03, with the desired value of 1.04.
A Broad-Band Analog Phase Shifter Design on I-Q Vector Modulator

Jun Yin,Wanshun Jiang,Zhigang Zhang

DOI: https://doi.org/10.1109/icmmt.2010.5525004

2010-01-01

Abstract:Phase shifter is widely applied in some area, including communication and radar. In the study, the principle of broadband analog phase shifter on I-Q modulating is introduced, which is validated by the theory design using Ansoft serenade. The microwave phase shifter on I-Q modulating broadband is simulated and the corresponding entity is designed. Finally, some test are done to the phase shifter, and we sum up the design experience, all those can provide some design experience with the engineers.
Tunable Multi-Tap Microwave Photonic Filter With Complex Coefficients Using A Dual-Parallel Mach-Zehnder Modulator

yi wang,xaofeng jin,hao chi,xianmin zhang,shilie zheng

DOI: https://doi.org/10.1080/09500340.2013.831138

IF: 1.3

2013-01-01

Journal of Modern Optics

Abstract:We propose and demonstrate a tunable multi-tap microwave photonic filter (MPF) with complex coefficients. It is based on addition of carrier suppressed single sideband (CS-SSB) signal and phase-controllable optical carrier. Instead of using the technique of optical filtering, the CS-SSB signal is generated by a dual-parallel Mach-Zehnder modulator (DPMZM) in our scheme. Frequency tuning of the filter is achieved by changing the phase of the optical carrier, which can be controlled by a variable optical delay line (VDL). The proposed structure features high flexibility and wideband RF response, and the experimental results demonstrate that it can be tuned continuously over one free spectral range (FSR) without changing the spectral shape of the filter.
Robust Reconfigurable Radiofrequency Photonic Filters Based on a Single Silicon In-Phase/quadrature Modulator

Hengsong Yue,Tao Chu

DOI: https://doi.org/10.1515/nanoph-2023-0459

2023-01-01

Abstract:Combining integrated photonics and radiofrequency (RF) signals in the optical domain can help overcome the limitations of traditional RF systems. However, it is challenging to achieve environmentally insensitive filtering in wireless communications using integration schemes. In this report, the performance of robust RF filters based on a single silicon in-phase/quadrature modulator with significantly improved temperature and optical carrier wavelength sensitivities, which were suppressed by more than three orders of magnitude compared with those of silicon resonators, was experimentally evaluated. Upconversion and the processing of signals were simultaneously realized on the modulator by setting the relative phases of the arms and the bias voltages. Moreover, the filters can be reconfigured as low-pass, high-pass, band-pass, or band-stop filters. From 25 to 75 °C, the center frequency variation was within 0.2 GHz. From 1500 to 1600 nm, the center frequency variation was within 2 GHz. The proposed scheme allows for filtering and reconfiguration without the use of optical processing modules such as resonators or delay lines, thus providing a novel approach to signal processing and a new robust filter for scenarios with dynamic environments.
High-Q Microwave Photonic Filter with Self-Phase Modulation Spectrum Broadening and Third-Order Dispersion Compensation

Dan Zou,Xiaoping Zheng,Shangyuan Li,Hanyi Zhang,Bingkun Zhou

DOI: https://doi.org/10.3788/col201412.080601

IF: 2.56

2014-01-01

Chinese Optics Letters

Abstract:We propose and experimentally demonstrate a scheme of high-Q microwave photonic filter (MPF) using the techniques of self-phase modulation (SPM) spectrum broadening and third-order dispersion (TOD) compensation. The optical pulses from a mode-locking laser are spectrally broadened by the SPM in the highly nonlinear fiber. A wideband optical frequency comb with 365 spectral lines within 10-dB power variation from the highest spectral power is obtained. By applying a cubic phase modulation via a waveshaper, the effect of TOD which broadens the MPF passband is eliminated. The final implemented MPF has a Q-value as high as 296 and a tuning range of 700 MHz.

Memory-Mapped Architectures

Mass-selective removal of ions from Paul traps using parametric excitation

Possibility of operating quadrupole mass filter at high resolution

Mass Peak Shape Improvement of A Quadrupole Mass Filter when Operating with A Rectangular Wave Power Supply

Two stability islands of quadrupole mass filter near q = 0.9 created by auxiliary radio frequency voltage.

An Ultra Broadband Passive Vector Modulator Phase Shifter

Simulation Study of a Planar Quadrupole Mass Filter for MEMS Mass Spectrometer

Tandem RF-only quadrupole mass filter with quadrupolar excitation

Mass Selection of Ions from Beams Using Waveform Isolation in Radiofrequency Quadrupoles

Dipole and quadrupole resonance excitation in linear quadrupoles

Simulation of a Quadrupole Mass Filter with Octupole Field

Simulation study of digital waveform‐driven quadrupole mass filter operated in higher stability regions for high‐resolution inductively coupled plasma mass spectrometry

Square Parametric Excitation: A Digital Resonant Method for the Quadrupole Ion Trap

Increasing Isolation Efficiency Using a Segmented Quadrupole Mass Filter Operated with Rectangular Waveforms

A Strategy for Simultaneously Improving Resolution and Sensitivity of Hybrid Quadrupole Ion Trap/Time-of-Flight Mass Spectrometry Using Square Waveform Phase Modulation

Quadrupole mass filters with octopole fields.

Field tuning and rf measurements of the four-vane radio frequency quadrupole with ramped inter-vane voltage

A Broad-Band Analog Phase Shifter Design on I-Q Vector Modulator

Tunable Multi-Tap Microwave Photonic Filter With Complex Coefficients Using A Dual-Parallel Mach-Zehnder Modulator

Robust Reconfigurable Radiofrequency Photonic Filters Based on a Single Silicon In-Phase/quadrature Modulator

High-Q Microwave Photonic Filter with Self-Phase Modulation Spectrum Broadening and Third-Order Dispersion Compensation