Abstract:Experimental, analytical and numerical methods have been employed to study the aerodynamic performance of four different cooled tips with coolant mass ratios between zero and 1.2% at three tip gaps of 1%, 1.6% and 2.2% of the chord. The four cooled tips are two flat tips with different coolant holes, a cooled suction side squealer tip and a cooled cavity tip. Each tip has ten coolant holes with the same diameter.The uncooled cavity tip produces the smallest loss among all uncooled tips. On the cooled flat tip, the coolant is injected normally into the tip gap and mixes directly with flow inside the tip gap. The momentum exchange between the coolant and the flow that enters the tip gap creates significant blockage. As the coolant mass flow ratio increases, the tip leakage loss of the cooled flat tip first decreases and then increases. For the cooled cavity tip, the blockage effect of the coolant is not as big as that on the cooled flat tip. This is because after the coolant exits the coolant holes, it mixes with flow in the cavity first, and then mixes with tip flow in the tip gap. The tip leakage loss of the cooled cavity tip increases as the coolant mass flow ratio increase. As a result, at a tip gap of 1.6% of the chord, the cooled cavity tip gives the lowest loss.At the smallest tip gap of 1% of the chord, the cooled flat tip produces less loss than the cooled cavity tip when the coolant mass flow ratios larger than 0.23%. This is because with the same coolant mass flow ratio, a proportionally larger blockage is created at the smallest tip gap. At the largest tip gap of 2.2% of the chord, the cavity tip achieves the best aerodynamic performance. This is because, the effect of the coolant is reduced and the benefits of the cavity tip geometry dominate. At a coolant mass flow ratio of 0.55%, the cooled flat tips produce a lower loss than the cavity tip at tip gaps less than 1.3% of the chord. The cooled cavity tip produces the least loss for tip gaps larger than 1.3% of the chord. The cooled suction side squealer has the worst aerodynamic performance for all tip gaps studied.

Comparison of Turbine Tip Leakage Flow for Flat Tip and Squealer Tip Geometries at High-Speed Conditions

Squealer Tip Leakage Flow Characteristics in Transonic Condition

Effect of Squealer Geometry Arrangements on Tip Leakage Flow and Heat Transfer for Turbine Blade

Tip Leakage Flow And Heat Transfer Predictions For Turbine Blades

Squealer Geometry Effects on Aerothermal Performance of Tip-Leakage Flow of Cavity Tips

STUDY ON TIP LEAKAGE FLOW AND HEAT TRANSFER FOR A SQUEALER TIP BLADE

Effects of Squealer Tip on Blade Aerodynamic Performance and Tip Heat Transfer in Gas Turbine

The Tip Leakage Flow of an Unshrouded High Pressure Turbine Blade with Tip Cooling

Experimental Study on Axially Non-Uniform Clearances in a Linear Turbine Cascade with a Cavity Squealer Tip

Aerothermal Characteristics of Transonic Over-Tip Leakage Flow for Different Tip Geometries with Cooling Injection

Numerical Investigation of Opening Double Squealer Groove Turbine Tip Clearance Flow Character

Transonic Turbine Blade Tip Aero-Thermal Performance With Different Tip Gaps: Part Ii-Tip Aerodynamic Loss

Transonic Turbine Blade Tip Aerothermal Performance with Different Tip Gaps—Part I: Tip Heat Transfer

Numerical Investigations on the Steady and Unsteady Leakage Flow and Heat Transfer Characteristics of Rotor Blade Squealer Tip

Aerothermal performance of cavity tip with flow structure effects in a transonic high-pressure turbine blade

Experimental and numerical investigations for turbine aerodynamic performance with different pressure side squealers and incidence angles

Aerodynamic performance of tip leakage flow of two different blade tips in transonic turbine

Computational Study Of The Thermal Performance Of An Unshrouded High Pressure Turbine Blade Tip

Unsteady Aerodynamics Of A Flat Tip And A Winglet Tip In A High-Pressure Turbine

Film Cooling and Aerodynamic Performance on Multi-Cavity Squealer Tip of a Turbine Blade

Effects of Rotor Squealer Tip with Non-Uniform Heights on Heat Transfer Characteristic and Flow Structure of Turbine Stage