Abstract:The effect of rolling temperature on the incomplete recrystallization behavior and the relationship to mechanical properties in 0.06C–4Mn-1.2Cr (wt.%) steel was investigated. Three plates of experimental steel were produced by hot rolling at different temperatures and intercritical annealing processes in this study. The microstructure of experimental steels was examined by optical microscopy (OM), scanning electron microscopy (SEM), X-ray diffraction (XRD), electron backscatter diffraction (EBSD), and transmission electron microscope (TEM). The mechanical properties of test steel were examined by impact test and tensile test. Austenite reversion and cementite precipitation-dissolution was numerically simulated under the assumption of local equilibrium. With the decrease of hot rolling temperature from 1000 °C to 800 °C, the uniform equiaxed prior austenite grains microstructures changed to heterogeneous microstructures of laminated and ultrafine prior austenite grains arranged alternatively. The tensile and impact tests revealed that the medium manganese steels rolling at 800 °C had an excellent combination of mechanical properties. Elongation had a great relationship with retained austenite fraction and stability. The fractography of impact specimens was examined to explore the toughening mechanism of the micro-laminated steels. The steel with uniform equiaxed grain structure exhibited a relatively low tensile strength of 750 MPa and low elongation of ∼20% and an extremely poor low-temperature toughness of ∼40 J at −40 °C. An enhanced low-temperature toughness (∼233 J at −40 °C), as well as an improved tensile strength (823 MPa) and higher elongation of ∼40%, was obtained in the steel with heterogeneous microstructures. The content of austenite in heterogeneous microstructure is twice that in uniform equiaxed grain structure. And cementite dissolved more thoroughly in the heterogeneous microstructure. The high austenite content of heterogeneous microstructures enabled the steel to be significantly stronger and ductile, which contributed to the high tensile strength and elongation to some extent. It is concluded that the effect of interface decohesion resulted in the occurrence of delamination. And the high austenite content and delamination greatly improved the low-temperature toughness of experimental steel.

Analysis of Plastic Deformation Instabilities at Elevated Temperatures in Hot-Rolled Medium-Mn Steel

The Portevin-Le Chatelier Effect in Al-Mg Alloy Investigated by Infrared Pyrometry

Explanation of the PLC Effect in Advanced High-Strength Medium-Mn Steels. A Review

Temperature-Dependent Macroscopic Mechanical Behaviors and Their Microscopic Explanations in a Medium Mn Steel

Effect of Deformation Temperature on Microstructure Evolution and Mechanical Properties of Low-Carbon High-Mn Steel

Hot Workability of High Manganese Transformation Induced Plasticity Steel

Strain Rate Sensitivity of Low‐Temperature Superplastic Heterogeneous Medium‐Mn Steel Fabricated by a Novel High‐Ratio Differential Speed Rolling

Review on the plastic instability of medium-Mn steels for identifying the formation mechanisms of Lüders and Portevin–Le Chatelier bands

Microstructure evolution and mechanical properties of metastable austenitic medium Mn steel fabricated by warm caliber rolling

Mesoscopic nature of serration behavior in high-Mn austenitic steel

Effect of rolling temperature on microstructure and mechanical properties of medium manganese steel

Deformation mechanism and microstructure evolution of medium-Mn AHSS under various loading conditions

Deformation Behavior and Microstructure of Low Carbon High Manganese Steels in Tensile Strain

Unusual step-like stress flow behavior and mechanisms of a 1.3 GPa grade medium-Mn steel with 51.2 % ductility

Microstructure Evolution and Mechanical Behavior of A Hot-Rolled High-Manganese Dual-Phase Transformation-Induced Plasticity/Twinning-Induced Plasticity Steel

A Critical Review on the Portevin-Le Chatelier Effect in Aluminum Alloys

Effect of grain size on dynamic strain aging behavior of C-bearing high Mn twinning-induced plasticity steel

Suppression of Inhomogeneous Plastic Deformation in Medium-Carbon Tempered Martensite Steel

Investigation of Constitutive Relationship and Dynamic Recrystallization Behavior of 22mnb5 During Hot Deformation

Thermal deformation behavior and microstructure evolution of Fe−8.5Mn−1.5Al light−weight medium manganese steel

Abnormal room temperature serrated flow and strain rate dependence of critical strain of a Fe-Mn-C twin-induced plasticity steel