Abstract:Homogenously doped and mixed yttria stabilized zirconia, YSZ (with 3 and 10mol% Y2O3 known as 3YSZ and 10YSZ) and NiO/10YSZ co-precipitates (nominally corresponding to 7, 12, 24, 30, 35 and 45vol.% Ni metal), were synthesized using a continuous hydrothermal flow synthesis (CHFS) system which uses a stream of superheated water at 450°C and 24.1MPa as a reaction medium to cause rapid precipitation of metal oxide nanoparticle co-precipitates from a mixed metal salt solution. All products were obtained directly from the outlet of the CHFS reactor as a slurry, which was then cleaned and freeze-dried prior to further processing. The highly crystalline nano-powdered products were characterized using a range of analytical methods, including: powder X-ray diffraction (XRD), energy dispersive spectroscopy (EDS), transmission electron microscopy (TEM), Raman spectroscopy and BET surface area measurements. Spherical primary particles of 10YSZ and 3YSZ were observed under the TEM and found to be 5.0±0.8nm (range 3.2–6.3nm) and 6.2±1.4nm (range 3.3–8.4nm) in size, with measured BET surface areas of 160.6 and 241.7m2g−1, respectively. Sintering of the nano-powder co-precipitates was performed via spark plasma sintering (SPS) at 1100°C for 1min, leading to densities of ca. 98% for 10YSZ and ca. 96% for Ni/10YSZ cermets (all NiO was converted into Ni due to the reducing atmosphere of the SPS). The 24% Ni/10YSZ cermet was subjected to focused ion beam tomography, which allowed the 3D arrangement of the conducting Ni metallic network of the dense cermet to be elucidated, and showed that a complete 3D network of Ni existed throughout the dense cermet disk. Electrical conductivity tests showed that the samples exhibited higher than expected electrical conductivity (for such low metal content), e.g., the 24vol.% Ni-containing sample achieved an electrical conductivity of ∼200Scm−1 at the fuel cell operating temperature, which corresponds to an effective conductivity of ∼117Scm−1 if a porosity of 30% were to be introduced.

Plastic shaping of NiFe2O4‐based cermets using granular feedstock: microstructure and mechanical properties

Complex-shaped TiC/Ti(C,N)-based cermet prepared via rheological press molding using highly-filled granular feedstock

Strong and densified 3D metal-ceramic composite with strengthened layer structure by material extrusion additive manufacturing

Highly conductive low nickel content nano-composite dense cermets from nano-powders made via a continuous hydrothermal synthesis route

Ultrafast pressureless sintering of high conductivity Ni-based cermets inert anode for Carbon‐free electrolytic aluminum

Influence of Fabrication Process on Magnetic Properties of Co-Finemet Nanocrystalline Powder Core

Fe3O4/C Composites Synthesized from Fe-based Xerogels for Anode Materials of Li-ion Batteries

Achieve a high electrochemical oxidation activity by a self-assembled cermet composite anode with low Ni content for solid oxide fuel cells

Microstructure and Properties of Ti(C,N)-Based Cermets with AlxCoCrFeNiTi Binder

Effects of CrMnFeCoNi additions on microstructure, mechanical properties and wear resistance of Ti(C,N)-based cermets

Advanced Multi-Metallic SOFC Anode Development by Mechanical Alloying Route

Effect of Metallic Content on Mechanical Property of Ni/(10NiO-NiFe2O4) Cermets

Microstructure and Mechanical Properties of Ni/10 Mol% Sc2O3–1 Mol% CeO2–ZrO2 Cermet Anode for Solid Oxide Fuel Cells

Submicron Ti(C,N)-based cermets with improved microstructure using high-energy milled and subsequent heat-treated ultrafine Ti(C,N) powders

Preparation and characterization of Ni-Fe-CCC composite for low-temperature ceramic fuel cell

An interesting application-oriented design of high-strength anode support for protonic ceramic fuel cells by a non-proton-conducting cermet

Preparation and SEM of Ni/Ce-YSZ Anode Materials

Fabrication of large cross-section Ti–6Al–4V alloy using EBS-modified POM-based feedstock

A strong, lightweight, and damping cermet material with a nacre-like ultrafine 3D interpenetrated architecture

Production of high-property Cr3C2-based cermet with Cr3C2–10WC composite powder as starting material

Effect of synthetic Mo2FeB2 powder on the microstructure and mechanical properties of Mo2FeB2-based cermets