Abstract:Trace gas analysis for SF6 decomposition is a powerful diagnostic method to identify partial discharge problem occurring in electrical equipment. In particular, it is recognized that the SF6 decomposition gases (such as CO, H2S, SO2 and CF4) can effectively determine the inner insulation condition of the electrical equipment. Currently, most of researches of diagnostic methods cannot meet the online high-precision detection of gas derivatives in SF6 electrical insulation equipment. Therefore, there is a need of developing a sensitive, selective and cost-effective sensor system for CO detection in an SF6 buffer gas environment due to the fact that the power system is filled with pure SF6 as the dielectric gas, which means that the concentration of SF6 is usually > 99.8%. The traditional photoacoustic CO gas sensors cannot be directly used in power system, since several SF6 physical constants strongly differ from those of N2 or air. In addition, SF6 molecule reveals uninterrupted and strong absorption lines in the mid-infrared spectral region. In this work, a CO gas sensor working in high concentration SF6 background gas is designed by using a distributed feedback (DFB) laser as an excitation source with a center wavelength of 2.3 μm. The absorption line strength of 2.3 μm is ~ two orders of magnitude higher than the absorption line strength around 1.56 μm, which can improve the sensor detection performance. A background-gas-induced high-Q differential photoacoustic cell is simulated numerically and tested experimentally. The quality factor of the designed photoacoustic cell in pure SF6 gas is 85, which is ~ 4 times higher than that in N2 carrier gas. The experimental results show that the maximum gas flow rate of the differential structure photoacoustic cell is ~ 6 times higher than that of the single resonant cavity photoacoustic cell. After optimizing the resonance frequency, gas velocity and working pressure of the sensor system, the detection sensitivity of the volume fraction of 1.85 × 10–6 is achieved. In the case of the volume fraction of 50 × 10–6 CO/SF6 gas mixture, the maximum photoacoustic signal amplitude of 19.6 μV is obtained, the corresponding normalized noise equivalent concentration (1σ) is 3.68 × 10–8 cm–1·W·Hz1/2 in 1 s integration time. A linear fitting is implemented to evaluate the response of the sensor from 50 × 10–6 to 1000 × 10–6, resulting in an R square value of 0.9997. The CO photoacoustic gas sensor has high sensitivity, good selectivity and strong noise immunity, which can provide an on-line detection technology for potential insulation fault diagnosis in the power system. The capability of CO gas sensor can be improved by using a higher excitation optical output power and/or reducing the PAC resonator volume to increase the cell constant.

Highly sensitive photoacoustic multicomponent gas sensor for SF6 decomposition online monitoring

Highly Sensitive SO_2 Photoacoustic Sensor for SF_6 Decomposition Detection Using a Compact Mw-Level Diode-Pumped Solid-State Laser Emitting at 303 Nm

ppb-Level SO2 Photoacoustic Sensor for SF6 Decomposition Analysis Utilizing a High-Power UV Laser with a Power Normalization Method

Multi-pass Differential Photoacoustic Sensor for Real-Time Measurement of SF6 Decomposition Component H2S at the ppb Level

Trace Photoacoustic SO2 Gas Sensor in SF6 Utilizing a 266 Nm UV Laser and an Acousto-Optic Power Stabilizer.

All-optical photoacoustic detection of SF 6 decomposition component SO 2 based on fiber-coupled UV-LED

Detection of SF6 gas decomposition component H2S based on fiber-optic photoacoustic sensing

High Sensitive Detection for SF6 Decomposition Component of H2S Based on Laser Photoacoustic Spectroscopy

Ppb-Level H2s Detection for Sf6 Decomposition Based on A Fiber-Amplified Telecommunication Diode Laser and A Background-Gas-Induced High-Q Photoacoustic Cell

EC-QCL Based Photoacoustic Spectroscopy for Detection of SF6 Decomposition Components

Design and Optimization of Photoacoustic CO Gas Sensor for Fault Diagnosis of SF6 Gas Insulated Equipment

Research on the Detection of SF6 Decomposition Products Based on Non-Resonant Photoacoustic Spectroscopy

EC-QCL-based Photoacoustic Spectroscopy for Simultaneous Detection of SF6 and SO2F2

Detection of SF 6 Decomposition Components under Partial Discharge by Photoacoustic Spectrometry and Its Temperature Characteristic

Photoacoustic Spectroscopy: Trace CO Detection by Using 10 Mw Near-Infrared Laser and Cantilever Beam

Cantilever Enhanced Photoacoustic Spectrometry: Quantitative Analysis of the Trace H2S Produced by SF6 Decomposition

Detection of SF6 Decomposition Components H2S and CO2 Based on WDM and CRDS

Highly Sensitive and Precise Analysis of SF6 Decomposition Component CO by Multi-comb Optical-feedback Cavity Enhanced Absorption Spectroscopy with a 2.3 Μm Diode Laser.

Fiber-Optic Photoacoustic CO Sensor for Gas Insulation Equipment Monitoring Based on Cantilever Differential Lock-In Amplification and Optical Excitation Enhancement

Photoacoustic Spectroscopy Detection of SOF2 Characteristic Component Engendered in SF6 Decomposition Under Partial Discharge

ppb-Level SO2 Photoacoustic Sensors with a Suppressed Absorption-Desorption Effect by Using a 7.41 μm External-Cavity Quantum Cascade Laser