Abstract:Trace gas analysis for SF6 decomposition is a powerful diagnostic method to identify partial discharge problem occurring in electrical equipment. In particular, it is recognized that the SF6 decomposition gases (such as CO, H2S, SO2 and CF4) can effectively determine the inner insulation condition of the electrical equipment. Currently, most of researches of diagnostic methods cannot meet the online high-precision detection of gas derivatives in SF6 electrical insulation equipment. Therefore, there is a need of developing a sensitive, selective and cost-effective sensor system for CO detection in an SF6 buffer gas environment due to the fact that the power system is filled with pure SF6 as the dielectric gas, which means that the concentration of SF6 is usually > 99.8%. The traditional photoacoustic CO gas sensors cannot be directly used in power system, since several SF6 physical constants strongly differ from those of N2 or air. In addition, SF6 molecule reveals uninterrupted and strong absorption lines in the mid-infrared spectral region. In this work, a CO gas sensor working in high concentration SF6 background gas is designed by using a distributed feedback (DFB) laser as an excitation source with a center wavelength of 2.3 μm. The absorption line strength of 2.3 μm is ~ two orders of magnitude higher than the absorption line strength around 1.56 μm, which can improve the sensor detection performance. A background-gas-induced high-Q differential photoacoustic cell is simulated numerically and tested experimentally. The quality factor of the designed photoacoustic cell in pure SF6 gas is 85, which is ~ 4 times higher than that in N2 carrier gas. The experimental results show that the maximum gas flow rate of the differential structure photoacoustic cell is ~ 6 times higher than that of the single resonant cavity photoacoustic cell. After optimizing the resonance frequency, gas velocity and working pressure of the sensor system, the detection sensitivity of the volume fraction of 1.85 × 10–6 is achieved. In the case of the volume fraction of 50 × 10–6 CO/SF6 gas mixture, the maximum photoacoustic signal amplitude of 19.6 μV is obtained, the corresponding normalized noise equivalent concentration (1σ) is 3.68 × 10–8 cm–1·W·Hz1/2 in 1 s integration time. A linear fitting is implemented to evaluate the response of the sensor from 50 × 10–6 to 1000 × 10–6, resulting in an R square value of 0.9997. The CO photoacoustic gas sensor has high sensitivity, good selectivity and strong noise immunity, which can provide an on-line detection technology for potential insulation fault diagnosis in the power system. The capability of CO gas sensor can be improved by using a higher excitation optical output power and/or reducing the PAC resonator volume to increase the cell constant.

Sensitivity enhanced NIR photoacoustic CO detection with SF6 promoting vibrational to translational relaxation process

A Sensitive Carbon Monoxide Sensor Based On Photoacoustic Spectroscopy With A 2.3 Mu M Mid-Infrared High-Power Laser And Enhanced Gas Absorption

A Sensitive Carbon Monoxide Sensor Based on Photoacoustic Spectroscopy with a 2.3 μm Mid-Infrared High-Power Laser and Enhanced Gas Absorption

Photoacoustic Spectroscopy: Trace CO Detection by Using 10 Mw Near-Infrared Laser and Cantilever Beam

Fiber-Optic Photoacoustic CO Sensor for Gas Insulation Equipment Monitoring Based on Cantilever Differential Lock-In Amplification and Optical Excitation Enhancement

The Influence of CO2 Molecular Relaxation Dynamics on Photoacoustic Signal in Near Infrared(NIR)Range

Design and Optimization of Photoacoustic CO Gas Sensor for Fault Diagnosis of SF6 Gas Insulated Equipment

Compact and sensitive mid-infrared all-fiber quartz-enhanced photoacoustic spectroscopy sensor for carbon monoxide detection.

A Sensitive Carbon Dioxide Sensor Based on Photoacoustic Spectroscopy with a Fixed Wavelength Quantum Cascade Laser

Near-infrared laser photoacoustic gas sensor for simultaneous detection of CO and H2S

Cantilever enhanced fiber-optic photoacoustic microprobe for diffusion detection of sulfur dioxide

All-optical Non-Resonant Photoacoustic Spectroscopy for Multicomponent Gas Detection Based on Aseismic Photoacoustic Cell

Sensitive Intracavity Photoacoustic Spectrometer Based on CO 2 Waveguide Laser

Study Of Carbon Monoxide Detection Characteristics With A Tunable Photoacoustic Spectroscopy System

EC-QCL Based Photoacoustic Spectroscopy for Detection of SF6 Decomposition Components

Photoacoustic Spectrum Detection of CO Based on Optimizing Non-resonant Photoacoustic Pool

Research on High Sensitivity Detection of Carbon Monoxide Based on Quantum Cascade Laser and Quartz-Enhanced Photoacoustic Spectroscopy

Highly sensitive photoacoustic multicomponent gas sensor for SF6 decomposition online monitoring

Miniaturized nonresonant photoacoustic gas analyzer for CO2 detection

Small-volume Highly-Sensitive All-Optical Gas Sensor Using Non-Resonant Photoacoustic Spectroscopy with Dual Silicon Cantilever Optical Microphones.

Sensitive Detection of Carbon Monoxide Based on a QEPAS Sensor with a 2.3μm Fiber-Coupled Antimonide Diode Laser