Abstract:Porous Si2N2O/SiC ceramics is facilitated at 1200 °C for 10 min by microwave sintering. Rapid in‐situ production of Si2N2O fibers provided high mechanical properties of the samples. The porosity of the prepared sample is tailorable and the thermal insulation effect is excellent. Two steps strategy were taken to effectively produce porous Si2N2O/SiC ceramics: 1) direct foaming combined with sol‐gel curing at room temperature to form a green body, and 2) sintering assisted by in‐situ production of Si2N2O fibers under microwave sintering conditions. Non‐toxic silica sol was used to provide silicon source for in‐situ synthesis of Si2N2O, the silica sol could form a gel that stabilizes the bubbles, creating a porous structure. A thorough investigation was conducted into how different sintering temperatures affected the microstructure, flexural strength, and porosity of the porous Si2N2O/SiC composites. The main bonding phase in the porous composites was the Si2N2O with fiber morphology. The optimal microwave sintering temperature for fabricating porous Si2N2O/SiC ceramics, using a combination of sol‐gel and direct foaming techniques, has been determined to be 1200 °C. At this temperature, the porosity can be controlled between 73.32% and 83.16% by proportionally adjusting the ratio of the raw materials. Under the condition of high porosity, the thermal radiation is dominant and the thermal conductivity increases with the increase of temperature. With the decrease of porosity, the heat conduction is dominant, and the thermal conductivity decreases with the increase of temperature.

Preparation and property of porous calcium silicate ceramic by two‐step ultrafast high‐temperature sintering

Preparation of Fly Ash-Based Porous Ceramic with Alumina as the Pore-Forming Agent

Preparation of a High-Performance Porous Ceramic Membrane by a Two-Step Coating Method and One-Step Sintering

Low-temperature preparation of porous SiC ceramics using phosphoric acid as a pore-forming agent and a binder

Preparation of Porous SiC Ceramics Using Starch as Pore-forming Agent

Effect of sintering temperature on the phase, microstructural, physical, mechanical, and in vitro biomineralisation properties of porous wollastonite ceramics fabricated using the gel casting method

Porous Silica Ceramics with Uniform Pores from the In-Situ Foaming Process of Silica Poly-Hollow Microspheres in Inert Atmosphere

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

Ultrafast high-temperature sintering of bulk oxides

Preparation and properties of SiC honeycomb ceramics by pressureless sintering technology

Enhancing densification rate and the unusual 4H-SiC polytype stabilization in ultrafast high-temperature sintering of α-SiC

A Simple and Efficient Way to Prepare Porous Mullite Matrix Ceramics Via Directly Sintering SiO2-Al2O3 Microspheres

A general method to synthesize and sinter bulk ceramics in seconds

Preparation and properties of porous ceramics from spodumene flotation tailings by low-temperature sintering

Preparation of porous Al2O3 ceramics with enhanced properties by SLS using Al2O3 poly-hollow microspheres (PHMs) coated with CaSiO3 sintering additive

Aluminum titanate based composite porous ceramics with both high porosity and mechanical strength prepared by a special two-step sintering method

Synthesis of Porous Cordierite Using Rice Husk As Silica Source and Pore Forming Agent

Microstructure and properties of porous Si3N4 ceramics by gelcasting-self-propagating high-temperature synthesis (SHS)

Preparation and Properties of Porous Silicon Carbide Ceramics Through Coat-Mix and Composite Additives Process

Microstructure and properties of porous Si 3 N 4 ceramics fabricated by digital light processing combined with spark plasma sintering

INFLUENCE OF SINTERING PROCESS ON PROPERTY OF POROUS CERAMICS FROM QUARTZ SAND