Abstract:Tin-based Babbitt alloys are a widely used bearing bushing material which have good comprehensive properties. However, problems such as high-temperature softening and insufficient bearing capacity occur during their use, so the optimization of tin-based Babbitt alloys has become a research hotspot. In this paper, ZChSnSb11-6 alloy was mainly prepared by the gravity casting method, and different amounts of Zn were added to the alloy (the mass fraction values were 0 wt.%, 0.05 wt.%, 0.1 wt.%, 0.15 wt.%, and 0.2 wt.%, respectively). Through the hardness test, the tensile test, the friction and wear test, and the microstructure observation of the prepared alloy, the influence of Zn on the organization and properties of the ZChSnSb11-6 alloy was analyzed. The results show that the size of the SnSb hard phase changed with the increasing content of Zn. The size of the hard phase of the SnSb tended to increase first and then decrease, and the number of phase particles increased first and then decreased, resulting in changes in performance. Through comparison, it was learned that the addition of Zn can effectively improve the hardness, tensile strength, yield strength, and wear resistance of the alloy, but the elongation rate was reduced. When the Zn content was 0.1 wt.%, the hardness value of the alloy reached the maximum value, 25.82 HB, which increased by 7.3% when compared with the sample without Zn. The hardness of the Zn, 0.15 wt.%, is close to that of the Zn, 0.1 wt.%. Compared to the sample without Zn, the tensile strength and elongation of the alloy were maximized at a Zn content of 0.15 wt.%. Compared to the sample without the Zn, the tensile strength was increased by 21.29%, and the elongation rate was increased by 46%. An analysis showed that the alloy has good comprehensive mechanical properties when the Zn content is 0.15 wt.%.

A Study of the Bearing Characteristics of Zinc-Aluminum (ZA) Alloys

Zn-Based Alloys for Plain Bearings—Influence of Al and Cu Content on Mechanical Properties

Dry sliding wear characteristics of some zinc-aluminium alloys: a comparative study with a conventional bearing bronze at a slow speed

Dynamic Testing of Materials for Galvanising Pot Roll Bearings with Improved Performance

EXPERIMENTAL INVESTIGATION OF TRIBOLOGICAL CHARACTERISTICS ON AA7068–ZrB2 IN-SITU AMCs

Corrosion and wear performance and mechanism study of ZrB2/AA6016

Tribological and thermomechanical analysis of CaO (quicklime) particulates filled ZA-27 alloy composites for bearing application

Characterization of microstructure and wear behavior of nickel modified Zn-27% Al alloy casting

Study on the Tribological Properties and Fault Mechanisms of Copper-Based Alloy Journal Bearing under Different Working Conditions

Casting with Zinc Alloys

Characterization of mechanical and tribological properties of graphite and alumina reinforced zinc alloy (ZA-27) hybrid metal matrix composites

Wear behavior of Mg–10Y–4Gd–1.5Zn–0.4Zr alloy

New developments of high-zinc Al-Zn-Cu-Mn cast alloys

Effect of in situ TiC reinforcement and applied load on the high-stress abrasive wear behaviour of zinc–aluminum alloy

Insight into the Tribological Behavior of the Dual-Phase Nickel Aluminum Bronze Alloy by Multiscale Characterization

Hot tensile and fatigue behaviour of zinc–aluminum alloys produced by gravity and squeeze casting

Research Progress on Al-based Sliding Bearing Alloys

Influence of Zr content on microstructure and mechanical properties of As-cast Al-Zn-Mg-Cu alloy

Study on the Casting Techniques of the New Sliding Bearing Founding Alloy

Effect of Zn on Microstructure and Wear Resistance of Sn-Based Babbitt Alloy

Fabrication and Dry Sliding Wear Behavior of in Situ Al–K2ZrF6–KBF4 Composites Reinforced by Al3Zr and ZrB2 Particles