Abstract:High performance lightweight structures made of metal matrix composites (MMCs) are in demand for application in variety of industries such as aircraft, spacecraft, automobile, marine, sports equipment, etc. However, uniform distribution of the reinforcement phase to improve the mechanical properties and quality of MMCs has been the challenge for the manufacturing industries. Hence, researchers are focusing on the development of traditional low-cost method of producing metal matrix composites. In the view of above facts, an attempt is made to study the processing and characterization of Si-Al alloy reinforced with zirconium dioxide particulate composites in this paper. Hence, this paper concentrates on experimentally identifying the effect of stir cast and spray forming processing techniques followed by hot pressing on micro hardness, compressive strength, and tensile strength using Taguchi’s design of experiments for aluminum silicon matrix alloy reinforced with zirconium dioxide particulates. From the extensive experimentation on aluminum and silicon reinforced with the ZrO2 powder particulates, it was observed that there was an improvement in selected mechanical properties as the percentage of ZrO2 increased with 13 wt.% of silicon under spray forming processing technique compared to stir cast composites. This may be due to uniform distribution homogenous dispersion, larger work hardening rate, and structure of dislocation tangles around the ZrO2 particulates that occurred during spray forming processing technique. Further, results obtained from the interaction plot, contour plot, main effects plot, and analysis of variance (ANOVA) proved to be successful for identifying the optimum processing parameters for Si-Al alloy reinforced with zirconium dioxide particulate composites. Further, this paper also discusses wear study using pin on disc wear testing apparatus on spray forming processed aluminum and silicon (13.0 wt.%) alloy reinforced with the ZrO2 powder particulates based on Taguchi’s design of experiments followed by second order model generation for wear using response surface methodology. Finally, electrode wear study of spray forming processed aluminum and silicon alloy reinforced with the ZrO2 powder particulates using electric discharge machining by varying peak current (A), pulse on time (μs), and pulse off time (μs) using brass, copper, and graphite as electrode material based on L27orthogonal array. The understanding gained from the design of experiments in this paper can be used to develop future guidelines for processing and characterization of Si-Al alloy reinforced with zirconium dioxide particulate composites.

EXPERIMENTAL INVESTIGATION OF TRIBOLOGICAL CHARACTERISTICS ON AA7068–ZrB2 IN-SITU AMCs

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Tribological characteristics of AA8090-WC-ZrC metal matrix composites prepared by stir casting process for Aerospace applications

Analysis of Wear Behaviour of AA5052 Alloy Composites by Addition Alumina with Zirconium Dioxide Using the Taguchi-Grey Relational Method

Prediction of tribological performance of AA8011/wt.%ZrO2 based composites fabricated by stir casting route

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Investigate the mechanical properties of Aluminium Metal Matrix Composite

Mechanical and tribological behaviour of tungsten carbide reinforced aluminum LM4 matrix composites

Tribological and thermomechanical analysis of CaO (quicklime) particulates filled ZA-27 alloy composites for bearing application

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Influence of AlN particles on microstructure, mechanical and tribological behaviour in AA6351 aluminum alloy

Enhanced mechanical and tribological properties of ultrasonically assisted stir-cast AA7075 metal matrix composites in challenging corrosive environments

Processing, Mechanical Characterization, and Electric Discharge Machining of Stir Cast and Spray Forming-Based Al-Si Alloy Reinforced with ZrO2 Particulate Composites

Synthesis and Experimental Investigations of Tribological and Corrosion Performance of AZ61 Magnesium Alloy Hybrid Composites

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

Characterization of mechanical and tribological properties of graphite and alumina reinforced zinc alloy (ZA-27) hybrid metal matrix composites

CHARACTERIZATION OF WEAR RATE OF Al-12WT. %Si ALLOY BASED MMC REINFORCED WITH ZrO2 PARTICULATES

Effect of Percentage Variation on Wear Behaviour of Tungsten Carbide and Cobalt Reinforced Al7075 Matrix Composites Synthesized by Melt Stirring Method

Development, mechanical characterization and analysis of dry sliding wear behavior of AA6082–Metakaolin metal matrix composites

Mechanical properties, dry sliding wear resistance, and microstructural characterization of in-situ Al-17Si-Al3Zr/Al2O3 FG-composite synthesized via vertical centrifugal casting technique

Preparation and mechanical and tribological properties of A1(3)Zr+6082Al composites fabricated by magnetic stirring in situ