Abstract:The most popular anode material in commercial Li-ion batteries is still graphite. However, its low intercalation potential is close to that of lithium, which results in the dendritic growth of lithium at its surface, and the formation of a passivation film that limits the rate capability and may result in safety hazards. High-performance anodes are thus needed. In this context, lithium titanite oxide (LTO) has attracted attention as this anode material has important advantages. Due to its higher lithium intercalation potential (1.55 V vs. Li+/Li), the dendritic deposition of lithium is avoided, and the safety is increased. In addition, LTO is a zero-strain material, as the volume change upon lithiation-delithiation is negligible, which increases the cycle life of the battery. Finally, the diffusion coefficient of Li+ in LTO (2 × 10−8 cm2 s−1) is larger than in graphite, which, added to the fact that the dendritic effect is avoided, increases importantly the rate capability. The LTO anode has two drawbacks. The energy density of the cells equipped with LTO anode is lower compared with the same cells with graphite anode, because the capacity of LTO is limited to 175 mAh g−1, and because of the higher redox potential. The main drawback, however, is the low electrical conductivity (10−13 S cm−1) and ionic conductivity (10−13–10−9 cm2 s−1). Different strategies have been used to address this drawback: nano-structuration of LTO to reduce the path of Li+ ions and electrons inside LTO, ion doping, and incorporation of conductive nanomaterials. The synthesis of LTO with the appropriate structure and the optimized doping and the synthesis of composites incorporating conductive materials is thus the key to achieving high-rate capability. That is why a variety of synthesis recipes have been published on the LTO-based anodes. The progress in the synthesis of LTO-based anodes in recent years is such that LTO is now considered a substitute for graphite in lithium-ion batteries for many applications, including electric cars and energy storage to solve intermittence problems of wind mills and photovoltaic plants. In this review, we examine the different techniques performed to fabricate LTO nanostructures. Details of the synthesis recipes and their relation to electrochemical performance are reported, allowing the extraction of the most powerful synthesis processes in relation to the recent experimental results.

Highly-Stable Li₄Ti₅O12 Anodes Obtained by Atomic-Layer-Deposited Al₂O₃

Li4Ti5O12 coated with ultrathin aluminum-doped zinc oxide films as an anode material for lithium-ion batteries

Fabrication of Li4Ti5O12 (LTO) as Anode Material for Li-Ion Batteries

Structural Analysis and Electrochemical Studies of Carbon Coated Li4ti5o12 Particles Used As Anode for Lithium Ion Battery

Ultrathin Titanium Dioxide Coating Enables High-Rate and Long-Life Lithium Cobalt Oxide

Li 1.4 Al 0.4 Ti 1.6 (PO 4 ) 3 -Modified Li 4 Ti 5 O 12 Anode for Lithium-Ion Storage with Enhanced Rate and Cycling Performance

Li4ti5o12-Coated Graphite Anode Materials for Lithium-Ion Batteries

Effective Oxygen‐Deficient Li4Ti5O12 Anode Material Displaying Excellent Rate Performance and Outstanding Cyclic Stability

Highly Stable Li1.2mn0.54co0.13ni0.13o2 Enabled By Novel Atomic Layer Deposited Aipo(4) Coating

Li4Ti5O12 Nanoparticles Prepared with Gel‐hydrothermal Process As a High Performance Anode Material for Li‐ion Batteries

Al2O3 Coating on BaLi2Ti6O14 Surface to Boost Its Stability and Rate Performance

Investigation on process mechanism of a novel energy-saving synthesis for high performance Li4Ti5O12 anode material

Elaborate strategy for preparing Li4Ti5O12-based anode materials with significantly improved lithium storage: TiO2 nanodots in-situ decoration and hierarchical structure construction

Electrochemical performance of Li4Ti5O12 anode materials synthesized using a spray-drying method

Synthesis and assessment of the electrochemical performance of micro-nano-spherical Li4Ti5O12-LiAlO2 composites

Synthesis and Electrochemical Performance of Li4Ti5O12 Submicrospheres Coated with TiN As Anode Materials for Lithium-Ion Battery

Simply AlF3-treated Li4Ti5O12 composite anode materials for stable and ultrahigh power lithium-ion batteries

Synthesis of dual-modified Fe-doped and carbon-coated Li4Ti5O12 anode based on industrial H2TiO3 for Li-ion batteries

A Low-Voltage Layered Na2 TiGeO5 Anode for Lithium-Ion Battery.

Investigation on Li4Ti5O12 Batteries Developed for Hybrid Electric Vehicle

Improving high-temperature performance of lithium-rich cathode by roll-to-roll atomic layer deposition of titania nanocoating for lithium-ion batteries