Abstract:The constraints of traditional manufacturing techniques have led to the generation of a considerable amount of waste superalloy, causing substantial resource wastage. The primary concern with waste superalloys lies in the excessive presence of inclusions and impurity elements, rendering them unsuitable for further utilization. This study proposes the use of directional solidification combined with electron beam melting and refining (EBMR) to prepare FGH4096 superalloy ingots (Φ120 mm), which offers a promising approach to produce large-sized powder superalloy master alloy ingots with high-purity and high homogeneity. It is found that the secondary dendrite arm spacing and the size of the γ' phase in the alloy are significantly reduced after EBMR treatment. The concentration of O and N can be decreased to 5.7 and 0.6 ppmw, respectively. The size of inclusion can be reduced below 8.69 μm and the inclusion numbers reduce by over 50 % compared with both conventional ingots. A droplet transfer mode and melt convection mode mechanism have been proposed, which accurately predicts the melting temperature and melt flow. A quantitative study is conducted on the influence of inclusion density, the contact angle between inclusions and melt, and the surface tension of the melt on capillary forces. The results indicate that the capillary forces between inclusions in the melt range from 1.8 × 10 −19 N and 1.9 × 10 −17 N. Furthermore, the collision-aggregation behavior of inclusions in the melt is discussed, and an estimate of the tendency of inclusion collision-aggregation is provided. The enrichment of inclusions in the EBMR ingot is primarily the result of turbulent collision. The Marangoni effect and the extremely high surface temperature of the melt promote the collision and agglomeration of inclusions, causing them to accumulate rapidly at the melt surface. Moreover, the thorough removal of inclusions through the decomposition and dissolution process of the electron beam offers theoretical backing for the preparation of superalloys through electron beam melting and high-purity refining.

Preparation method of iron, chromium and aluminum multielement electrothermal alloy with high resistance

High-temperature Oxidation Behavior of AlCoCrCuFeNi High-Entropy Alloy by Selective Laser Melting

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Rare-earth aluminum alloy and preparation method thereof

Electroslag refining processing of iron-aluminium based intermetallic alloys

Method for preparing bulk nanocrystalline iron-based alloy

THE WELDABILITY OF IRON-ALUMINIUM BASED INTERMETALLICS

Investigation on the Controllable Microstructures of High Iron Content Al–Fe Alloys Fabricated Via Solid–Liquid Mixture Method Combining with Plasma Arc Heating Approach

Study on Facile Fabrication Method and Performance of Iron-Based Amorphous Alloy/Al Micro-Laminated Composites

Grain refinement of Fe 3 Al-based iron aluminide fabricated using wire-arc additive manufacturing

High Strength and High Electrical Conductivity in Cu-Fe Alloys with Nano and Micro Fe Particles

Low Resistivity Aluminium Alloy of High Tensile Strength and Elongation

Magnesium alloy and preparation method thereof

Research on directional solidification combined with electron beam melting and refining for recycling of FGH4096 alloy scraps

Study on the process and microstructure of Fe34Mn13.5Al3Cr7.5Ni alloy prepared by spark plasma sintering based on elemental powder

Preparation and performance of iron-based amorphous strip/AZ31 Mg alloy laminated composites

Chemical Component Optimization Based on Thermodynamic Calculation of Fe-1.93Mn-0.07Ni-1.96Cr-0.35Mo Ultra-High Strength Steel

Preparation method for rare earth-magnesium alloy

Zirconium-strontium composite micro-alloyed high-toughness corrosion-resistant low-silicon-content aluminum-silicon-copper cast aluminum alloy and preparation method

Microstructure, mechanical properties and corrosion resistance of low-cost Ti–Al–Cr–Fe alloys processed via powder metallurgy

Designing Ultrastrong and Thermally Stable FeCrAl Alloys with the Fine-Grained Structure