Abstract:The room-temperature strength of Al0.3CoCrFeNi high-entropy alloys (HEAs) is relatively low owing to its intrinsic fcc structure. In the present study, the as-cast HEAs were subjected to cold rolling and subsequent annealing treatment (800, 900, and 1000 °C) to adjust the microstructures and tensile properties. This treatment process resulted in the partial recrystallization, full recrystallization, and grain coarsening with increasing the annealing temperature. It was found that the large and spherical B2 precipitates were generated in the recrystallized grain boundaries of three annealing states, while the small and elongated B2 precipitates were aligned along the deformation twins in the non-recrystallized region of the 800 °C-annealing state. The former B2 precipitates assisted in refining the recrystallized grains to quasi ultra-fine grain and fine grain regimes (with the grain sizes of ~0.9, ~2.2, and ~7.2 μm). The tensile results indicated that the decreased annealing temperature induced the gradual strengthening of this alloy but also maintained the ductility at the high levels. The yield strength and ultimate tensile strength in 800 °C-annealed specimen were raised as high as ~870 and ~1060 MPa and the ductility was maintained at ~26%. The strengthening behavior derived from the heterogeneous microstructures consisting of quasi ultra-fine recrystallized grains, non-recrystallized grains, deformation twins, dislocations, and B2 precipitates. Current findings offer the guidance for designing the HEAs with good strength and ductility.

B2-strengthened Al-Co-Cr-Fe-Ni high entropy alloy with high ductility

Microstructure and mechanical properties of Al-Fe-Co-Cr-Ni high entropy alloy fabricated via powder extrusion

Preparation and properties of FeNiMnCuC0.2Alx high-entropy alloy

Microstructural Evolution and Elevated-Temperature Strengthening Mechanism of Co-free FeCrMnNiV0.2Alx High-Entropy Alloys During Annealing

The cobalt-free Fe35Mn15Cr15Ni25Al10 high-entropy alloy with multiscale particles for excellent strength-ductility synergy

High strength and ductility in a dual-phase hetero-structured AlCoCrFeNi2.1 eutectic high-entropy alloy by powder metallurgy

Formation of hypoeutectic structure and strengthening mechanism of Co4Cr1.5Fe1.5Ni5 high entropy alloy alloyed by Al

Microstructural origins of high strength and high ductility in an AlCoCrFeNi2.1 eutectic high-entropy alloy

Study on strength and toughness of FeCoCrNiAlx high entropy alloy

High-strength and high-ductility AlCoCrFeNi2.1 eutectic high-entropy alloy achieved via precipitation strengthening in a heterogeneous structure

Multiscale-phase-driven strength-ductility synergy in Fe3Cr2CoNiAlx high entropy alloys

Nanoscale B2 precipitation and strengthening behavior in Al0.5CoCrFeNi high-entropy alloy

A novel as-cast precipitation-strengthened Al0.5V0.1FeCrMnNi0.9 high-entropy alloy with high strength and plasticity

Microstructural features and excellent compression properties of a novel Al0.7CoCrFeNiTi0.3 high entropy alloy

Microstructure Evolution and Mechanical Properties of Ultra-Fine Grain AlCrFe2Ni2Wx High-Entropy Alloys

L12 nanoparticles-strengthened Co2Ni2Cr medium entropy alloy showing an outstanding tensile property

Strength and ductility dual-enhancement of Ni36Co30Fe11Cr11Al6Ti5Nb1 high entropy alloy by directional solidification

Microstructural Evolution and Tensile Properties of Al0.3CoCrFeNi High-Entropy Alloy Associated with B2 Precipitates

Microstructure evolution and strengthening mechanisms in Ni36Co30Cr11Fe11Al12-xNbx high entropy alloys

Design of Novel Precipitate-Strengthened Al-Co-Cr-Fe-Nb-Ni High-Entropy Superalloys

Microstructure and tensile properties of high-entropy alloy Al0.5CoCrFeNi particles reinforced Ti/Al laminated composite