Abstract:Purpose: It was hypothesized in this in-vitro study that positioning a K-wire intersecting the cutting plane at the theoretical lateral hinge location would limit the cut depth and help preserve the lateral hinge during the opening of the osteotomy. Objectives were (1) to compare the mechanical resistance of the hinge and the protective effect of leaving the K-wire during the opening procedure (2) to check if the K-wire would limit the depth of the osteotomy. Methods: An ex-vivo mechanical study, testing 5 pairs of fresh-frozen tibias, was designed. CT-scan based Patient-specific cutting guides were obtained to define the cutting plane and the location of the K-wire at the hinge, using standardized 3D planning protocol. In each pair, OWHTO was performed either with or without the K-wire. To evaluate the hinge's resistance to fracture, the specimens were rigidly fixed at the proximal tibia and a direct load was applied on the free tibial diaphysis to open the osteotomy. The maximum load at breakage, maximum permissible displacement and maximal angulation of the osteotomy before hinge failure was measured. To assess the preservation of an unscathed hinge (protected by the K-wire), the distance from the end of the osteotomy cut to the lateral tibial cortical was measured in mm. Results: The maximum load to hinge breakage in the K-wires PsCG knees compared to the control group (48.3 N vs 5.5 N, p = 0.004), the maximum permissible displacement (19.8 mm vs 7.5 mm, p = 0.005) and the maximal angulation of the osteotomy before hinge breakage (9.9° vs 2.9°, p = 0.002) were all statistically superior in the K-wires PsCG knees compared to the control group. A mean distance of 10 ± 1 mm between cut-bone (saw-print) and lateral hinge cortical bone was found post-performing the osteotomy and the hinge failing. Conclusion: The maximum load to breakage and the maximum permissible displacement were, respectively, 880% and 260% higher during the opening of the OWHTO in using K-wires compared to the non-K-wire control group. This confirms the mechanical advantage of using a K-wire for both stabilization and protecting the Hinge during OWHTO. This comparative cadaveric study shows an improvement of the lateral hinges resistance to failing during the opening of the osteotomy. This can be achieved by the placement of a K-wire intersecting the cutting plane at the theoretical location of the lateral hinge.

Pull-out resistance of connected K-wires for osteosynthesis: development of a numerical model

Development of a Novel X-ray Compatible 3D-Printed Bone Model to Characterize Different K-Wire Fixation Methods in Support of the Treatment of Pediatric Radius Fractures

Enhancement Of Kirschner Wire For Bone Drilling

Adding a protective K-wire during opening high tibial osteotomy increases lateral hinge resistance to fracture

The effect of the angle between fracture line and Kirschner wires on stability in supracondylar humerus fractures treated with Kirschner wire fixation: A finite element analysis

Cadaveric biomechanical assessment of different configurations for a novel pin and plate fixation method in distal humerus fractures

Biomechanics of external fixator of distal radius fracture, a new approach: Mutifix Wrist

Osteosynthesis of Phalangeal Fractures: Biomechanical Comparison of Kirschner Wires, Plates, and Compression Screws

Effect of a figure-of-eight cerclage wire with two Kirschner wires on fixation strength for transverse metacarpal shaft fractures: an in vitro study with artificial bone

Biomechanical Analysis of the Kirschner-Wire Depth of the Modified Tension Band Wiring Technique in Transverse Patellar Fractures: An Experimental Study Using the Finite-Element Method

A Finite Element Model for investigating the influence of keel design and position on unicompartmental knee replacement cementless tibial component fixation

Where Should the Pins Be Placed to Decrease the Failure Rate after Fixation of a Mayo IIA Olecranon Fracture? A Biomechanical Analysis.

Auxetic fixation devices can achieve superior pullout performances compared to standard fixation concepts

Biomechanical Comparison between Inverted Triangle and Vertical Configurations of Three Kirschner Wires for Femoral Neck Fracture Fixation in Dogs: A Cadaveric Study

Analytical and Numerical Modeling of the Pullout Behavior between High-Strength Stainless Steel Wire Mesh and ECC

Novel screw-cable integrated system(SCIS) for minimally invasive treatment of patella transverse fractures: a finite element analysis

Stability of the Distal Phalanx Fracture - A Biomechanical Study on the Importance of the Nail and the Influence of Fixation by Crossing Kirschner Wires

A Novel Screw Modeling Approach to Study the Effects of Screw Parameters on Pullout Strength.

Fixation Performance of Bioabsorbable Zn-6Ag Pins for Osteosynthesis

Outcomes of an aseptic technique for Kirschner wire percutaneous pinning in the hand and wrist

The effect of Ding's screws and tension band wiring for treatment of olecranon fractures: a biomechanical study