Abstract:Ultra-thin flexible photovoltaic materials for solar cells, like transition metal di-chalcogenides (TMDCs), hold significant promise due to their advantageous properties in photon absorption and electronic transport, being composed of atomically thin 2D layered semiconductor materials. An essential 2D-layered substance, tungsten Disulfide (WS2), classified as a TMDC, has garnered substantial attention due to its notable chemical and physical characteristics. This work presents a novel method for getting good photovoltaic results using WS2 solar cells. The suggested configuration "Al/FTO/SnS2/WS2/CuO/Ni" comprises two absorber layers, which involves incorporating CuO as a supplementary absorber layer and SnS2 as the buffer layer. Several metals with varying work functions were investigated one at a time, therefore, Al and Ni were chosen for the front as well as back contact in order to produce a low resistance metal-semiconductor (M-S) interface. Additionally, aluminum (Al) and nickel (Ni), are commonly used due to their well-understood properties such as conductivity and thermal stability. Subsequently, an analysis was conducted to determine the effects of important influencing factors, such as operating temperature, layer thickness, defects density, and doping density of the absorber and buffer layers. The power conversion efficiency (PCE) was achieved approximately 30%, accompanied by an open circuit voltage (VOC) of 1.02 V, a short circuit current (JSC) of 34.35 mA/cm2, and a fill factor (FF) of 87.27%. This improvement was achieved by utilizing an Al/FTO/SnS2/WS2/CuO/Ni heterostructure. In comparison, the reference cell without CuO (single absorber) had a PCE of 21.74%, VOC of 0.88 V, JSC of 28.6 mA/cm2, and FF of 86.23%. The results obtained from an extensive numerical analysis and demonstrate the immense potential of the SnS2/WS2/CuO heterostructure, indicating a promising direction for the manufacturing of photovoltaic and photonic devices based on WS2-TMDCs. This study provides a systematic roadmap for the fabrication process as well as realization of low-cost high efficiency solar cell.

Numerical modeling and analysis of FeS2-based solar cell employing CuBi2O4 as back surface field layer

Numerical modeling of CuSbSe2-based dual-heterojunction thin film solar cell with CGS back surface layer

Design and numerical investigation of cadmium telluride (CdTe) and iron silicide (FeSi2) based double absorber solar cells to enhance power conversion efficiency

Numerical analysis of FeSi2 based solar cell with PEDOT:PSS hole transport layer

Design and numerical analysis of CIGS-based solar cell with V2O5 as the BSF layer to enhance photovoltaic performance

A qualitative Design and optimization of CIGS-based Solar Cells with Sn2S3 Back Surface Field: A plan for achieving 21.83 % efficiency

Design and simulation of a highly efficient CuBi2O4 thin-film solar cell with hole transport layer

Numerical Investigation of CuSbS2Thin Film Solar Cell using SCAPS-1D: Enhancement of Efficiency on Experimental Films by Defect Studies

Modeling and optimization of numerical studies on CuSbS 2 thin film solar cell with ∼ 15% efficiency

Design and optimization of WS2 based high performance double absorber solar cell

Numerical simulation of Sb2Se3-based solar cells

Numerical Simulation of High Efficiency Environment Friendly CuBi2O4-Based Thin-Film Solar Cell Using SCAPS-1D

Performance Enhancement of an MoS2-Based Heterojunction Solar Cell with an In2Te3 Back Surface Field: A Numerical Simulation Approach

Design and simulation of Cu2SnSe3-based solar cells using various hole transport layer (HTL) for Performance Efficiency above 32%

Numerical simulation on an efficient n-CdS/p-ZnSnN2/p+-Cu2SnS3/p++- CuGaSe2 thin film solar cell

Performance enhancement of CIGS-based solar cells by incorporating an ultrathin BaSi2 BSF layer

Investigation of Back Surface Field Layer for High Efficiency Ultrathin In2S3 based CIGS Solar Cell

Combined DFT, SCAPS-1D, and wxAMPS frameworks for design optimization of efficient Cs2BiAgI6-based perovskite solar cells with different charge transport layers

Performance evaluation of WS2 as buffer and Sb2S3 as hole transport layer in CZTS solar cell by numerical simulation

Concurrent investigation of antimony chalcogenide (Sb2Se3 and Sb2S3)-based solar cells with a potential WS2 electron transport layer

Numerical Simulation of Copper Indium Gallium Diselenide Solar Cell with Ultra-Thin BaSi2 Back Surface Field Layer Using the Non-Toxic In2Se3 Buffer Layer