Further studies on corticosteroidogenesis. V. 11 Beta-hydroxylation of deoxycorticosterone by mitochondria incubated with malate, supernatant fraction and supernatant fraction+pyruvate+CO2.

F. Péron,B. Caldwell

DOI: https://doi.org/10.1016/0005-2760(68)90164-1

1968-10-22

Biochimica et Biophysica Acta

Abstract:

What problem does this paper attempt to address?

Thickness Measurement of Composite Material Using Eddy Current Testing

Peihua Chen,Pingjie Huang,Bo Ye,Guohou Li,Zekui Zhou

DOI: https://doi.org/10.4028/www.scientific.net/amr.79-82.1995

2009-01-01

Advanced Materials Research

Abstract:Composite materials have some obvious advantages such as high specific strength, high specific modulus, corrosion resistant, abrasion resistant and so on, it is believed to be highly competitive compare to other materials. Advanced composite materials have been used more and more widely in defense industry, among them carbon fiber reinforced resin base composite material is most representative([1]) ,there has great value for the study of carbon fiber composite materials. Eddy current is a nondestructive testing technology widely used on metal materials, the using of eddy current technology in aviation domain has a long history, but there is few reports on composite material with eddy current NDT. Experiments show that eddy current used on composite material is feasible, and the result is satisfactory. The thickness measurements of carbon fiber advanced composite materials have been done in two different ways.
Fiber orientation assessment in complex shaped parts reinforced with carbon fiber using infrared thermography

Henrique-Coelho Fernandes,Xavier Maldague

DOI: https://doi.org/10.1080/17686733.2015.1022351

IF: 2.5

2015-01-02

Quantitative InfraRed Thermography Journal

Abstract:The use of composite materials is growing more and more every day in several applications. The arrangement or orientation of the fibers relative to one another have a significant influence on the strength and other properties of fiber reinforced composites. Thus, evaluation techniques are needed for measuring material fiber orientation. In this work infrared thermography is employed to assess the material’s fiber orientation. More specifically a pulsed infrared diode laser heating spot technique combined with a 3D model of the part is used in order to assess fiber orientation on the surface of carbon fiber-reinforced polymer complex shaped parts made of carbon/PEEK (Polyether ether ketone) randomly-oriented strands.

instruments & instrumentation,physics, applied,materials science, characterization & testing
Nondestructive Evaluation of Carbon Fiber Bicycle Frames Using Infrared Thermography

Rubén Usamentiaga,Clemente Ibarra-Castanedo,Matthieu Klein,Xavier Maldague,Jeroen Peeters,Alvaro Sanchez-Beato

DOI: https://doi.org/10.3390/s17112679

2017-11-20

Abstract:Bicycle frames made of carbon fibre are extremely popular for high-performance cycling due to the stiffness-to-weight ratio, which enables greater power transfer. However, products manufactured using carbon fibre are sensitive to impact damage. Therefore, intelligent nondestructive evaluation is a required step to prevent failures and ensure a secure usage of the bicycle. This work proposes an inspection method based on active thermography, a proven technique successfully applied to other materials. Different configurations for the inspection are tested, including power and heating time. Moreover, experiments are applied to a real bicycle frame with generated impact damage of different energies. Tests show excellent results, detecting the generated damage during the inspection. When the results are combined with advanced image post-processing methods, the SNR is greatly increased, and the size and localization of the defects are clearly visible in the images.
Active Infrared Thermography for Interfacial Defects Detection on Composite Cross-Arms Based on Finite Element Simulation

Zhen Huang,Zheng Wang,Yanxin Tu,Fanghui Yin,Liming Wang,Xiangyang Peng

DOI: https://doi.org/10.1109/CEEPE58418.2023.10165732

2023-01-01

Abstract:Composite transmission towers have become a key trend in the development of transmission and substation systems in recent years, and composite cross-arms have begun to replace traditional steel cross-arms in some lines. The interface of composite cross-arms, on the other hand, might be faulty owing to its variables and external environmental influence. Existing detection technologies have several limitations, and active infrared thermography, as a new technology, has demonstrated its efficacy in identifying faults in composite materials. In this work, the thermal response characteristics of composite cross-stretcher interface flaws are comprehensively investigated using the finite element simulation method. The thermal response characteristics of interface defects of various sizes, depths, and kinds are compared, and the temperature variation characteristics of the defects are described using linear and logarithmic coordinates. The nature of the defect can be extracted from the rate of temperature change and the temperature in the smooth phase in linear coordinates, and the nature of the defect can be extracted from the curve shift time, magnitude, and direction in logarithmic coordinates. The research presented in this work demonstrates that active infrared thermography can effectively distinguish interface defects in composite cross-arms.
3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

L. Gahleitner,G. Thummerer,B. Reitinger,K. Meirer,G. Mayr

DOI: https://doi.org/10.1016/j.ndteint.2022.102702

2022-07-03

Abstract:This paper presents results from 3D photothermal reconstruction of real subsurface defects in carbon fiber-reinforced polymers using the virtual wave concept. We apply pulsed thermography during and after interrupted fatigue loading in tensile-tensile configuration for notched multidirectional laminates. In addition, we discuss the influence of the ambient conditions from in-situ photothermal testing on the virtual wave signal. The results obtained from 3D photothermal reconstruction are directly compared with those obtained from laser ultrasound testing. To summarize, we demonstrate a practicable and fast 3D photothermal evaluation of subsurface defect evolution utilizing the virtual wave concept.

materials science, characterization & testing
Infrared thermographic inspection of 3D hybrid aluminium-CFRP composite using different spectral bands and new unsupervised probabilistic low-rank component factorization model

Henrique Fernandes,Hai Zhang,Steven Quirin,Jue Hu,Michael Schwarz,Hendrik Jost,Hans-Georg Herrmann

DOI: https://doi.org/10.1016/j.ndteint.2021.102561

2022-01-01

Abstract:In this work, infrared thermography is used to detect defects on a 3D hybrid aluminium-CFRP composite structure. First, radiometric calibration and geometric distortion correction are performed for 3D inspection. Second, we propose a new unsupervised probabilistic low-rank component factorization thermographic de-noising model to improve image performance and defect visualization. Signal profiles and standard deviation analysis is used to assess the results, and x-ray CT inspections are compared to the infrared inspection results. Finally, we can conclude that the proposed algorithm can detect voids and resin rich areas presenting a better image performance if compared to direct infrared inspection results.

materials science, characterization & testing
Numerical Modelling of the Heat Source and the Thermal Response of an Additively Manufactured Composite during an Active Thermographic Inspection

Arnaud Notebaert,Julien Quinten,Marc Moonens,Vedi Olmez,Camila Barros,Sebastião Simões Cunha Jr,Anthonin Demarbaix

DOI: https://doi.org/10.3390/ma17010013

2023-12-19

Abstract:This paper deals with the numerical modelling of non-destructive testing of composite parts using active thermography. This method has emerged as a new approach for performing non-destructive testing (NDT) on continuous carbon fibre reinforced thermoplastic polymer (CCFRTP) components, particularly in view of detecting porosity or delamination. In this context, our numerical model has been developed around references containing internal defects of various shapes and sizes. The first novelty lies in the fact that the heat source used in the experimental setup is modelled exhaustively to accurately model the radiation emitted by the lamp, as well as the convection and conduction around the bulb. A second novelty concerns the modelling of the CCFRTP making up the benchmark used. Indeed, its thermal properties vary as a function of the sample temperature. Therefore, the actual thermal properties have been experimentally measured and were later used in our model. The latter then captures the material dependency on temperature. The results obtained by our model proved to be in close agreement with the experimental results on real reference points, paving the way for future use of the model to optimise experimental configurations and, in particular, the heating parameters.
Independent component thermography for non-destructive testing of defects in polymer composites

Yi Liu,Jin-Yi Wu,Kaixin Liu,Hsiu-Li Wen,Yuan Yao,Stefano Sfarra,Chunhui Zhao

DOI: https://doi.org/10.1088/1361-6501/ab02db

IF: 2.398

2019-03-07

Measurement Science and Technology

Abstract:Thermographic data processing and analysis is critical for effective infrared thermography non-destructive testing of defects in composite materials. In this research work, the concept of blind source separation is introduced into this field for facilitating subsurface defect detection in polymer composites. In detail, a thermal image generated by infrared thermography is viewed as a linear mixture of several independent and non-Gaussian sources, which can be decomposed by adopting the proposed independent component thermography (ICT) technique. After the decomposition, the non-Gaussian sources are extracted and plotted as a number of images with the same size as the original thermograms. Eventually, the defect signals can be separated from the non-uniform backgrounds which are usually caused by uneven heating. As a result, the location and shape information of the subsurface defective regions is highlighted. The feasibility of the ICT method is illustrated with its application to a carbon fiber reinforced polymer specimen.

engineering, multidisciplinary,instruments & instrumentation
A Comparison among Different Ways to Investigate Composite Materials with Lock-In Thermography: The Multi-Frequency Approach

Ester D'Accardi,Davide Palumbo,Umberto Galietti,Ester D’Accardi

DOI: https://doi.org/10.3390/ma14102525

IF: 3.4

2021-05-12

Materials

Abstract:The main goal of non-destructive testing is the detection of defects early enough to avoid catastrophic failure with particular interest for the inspection of aerospace structures; under this aspect, all methods for fast and reliable inspection deserve special attention. In this sense, active thermography for non-destructive testing enables contactless, fast, remote, and not expensive control of materials and structures. Furthermore, different works have confirmed the potentials of lock-in thermography as a flexible technique for its peculiarity to be performed by means of a low-cost set-up. In this work, a new approach called the multi-frequency via software approach (MFS), based on the superimposition via software of two square waves with two different main excitation frequencies, has been used to inspect a sample in carbon fiber reinforced polymers (CFRP) material with imposed defects of different materials, sizes and depths, by means of lock-in thermography. The advantages and disadvantages of the multi-frequency approach have been highlighted by comparing quantitatively the MFS with the traditional excitation methods (sine and square waves).

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
A novel force-temperature model for evaluating internal forces in CFRP by means of infrared thermography

Pengfei Zhu,Rongbang Wang,Stefano Sfarra,Vladimir Vavilov,Xavier Maldague,Hai Zhang

DOI: https://doi.org/10.1016/j.ndteint.2024.103066

IF: 4.683

2024-02-07

NDT & E International

Abstract:Carbon fibre reinforced polymer (CFRP) composites are commonly used in the aerospace industry due to their excellent mechanical properties. The extreme mechanical environments make CFRP to exceed its yield limit, which is associated with composite defects, such as delaminations and cracks. Therefore, it is important to develop a stable, non-contact and highly accurate stress measurement technique. In this work, a novel internal stress measurement technique is proposed being based on the elastic plate theory and thermal stress analysis. By analyzing the temperature distribution on the material external surface, one can evaluate composite mechanical behaviour and internal stresses. To validate the proposed novel method, the theoretical investigations, including numerical simulations and experiments, have been performed, and the experimental results were optoimized by applying the Levenberg-Marquardt. Theoretical and experimental results have been used to predict the force loaded on the sample surface. Furthermore, the effects of coating on the stress inversion problem have also been discussed.

materials science, characterization & testing
Enhanced Infrared Sparse Pattern Extraction and Usage for Impact Evaluation of Basalt-Carbon Hybrid Composites by Pulsed Thermography

Jue Hu,Hai Zhang,Stefano Sfarra,Claudia Sergi,Stefano Perilli,Clemente Ibarra-Castanedo,Guiyun Tian,Xavier Maldague

DOI: https://doi.org/10.3390/s20247159

IF: 3.9

2020-12-14

Sensors

Abstract:Nowadays, infrared thermography, as a widely used non-destructive testing method, is increasingly studied for impact evaluation of composite structures. Sparse pattern extraction is attracting increasing attention as an advanced post-processing method. In this paper, an enhanced sparse pattern extraction framework is presented for thermographic sequence processing and defect detection. This framework adapts cropping operator and typical component extraction as a preprocessing step to reduce the dimensions of raw data and applies sparse pattern extraction algorithms to enhance the contrast on the defect area. Different cases are studied involving several defects in four basalt-carbon hybrid fiber-reinforced polymer composite laminates. Finally, comparative analysis with intensity distribution is carried out to verify the effectiveness of contrast enhancement using this framework.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Joint Scanning Laser Thermography Defect Detection Method for Carbon Fiber Reinforced Polymer

Zhiyi He,Hongjin Wang,Yunze He,Guixiang Zhang,Jiazheng Wang,Gaoyu Zou,Tomasz Chady

DOI: https://doi.org/10.1109/jsen.2019.2941077

IF: 4.3

2020-01-01

IEEE Sensors Journal

Abstract:In this paper, a new inspection method, joint scanning laser thermography (JSLT) as well as its data reconstruction and processing algorithm, is proposed. The new inspection method is utilized to detect and characterize the flat-bottom holes (FBH) in carbon fiber composites by using joint laser scanning scheme. By analyzing the nature of the thermal image sequences sampled under such a scanning scheme, a quick and simple reconstruction method is developed to characterize the buried depth of defects based on 1D heat conduction model. The processed thermal images are expected to get higher temporal resolution and spatial resolution. It can inspect larger area within shorter acquisition time than the pulse thermography. Thus, the study solves the dilemma between the inspection speed and the inspection capacity. Later, a joint laser scanning thermography test is set up to test the algorithm on a carbon fiber composite panel with defects buried at different depth. The experimental results show that the reconstructed data almost behave as those under pulse excitation. The tendency of temperature to change in the logarithmic domain over time is similar to the curve in the TSR method. But, unlike the pulse thermography data, the defect detection rate of PCA based on reconstructed data is higher than that of fast Fourier transform (FFT) amplitude image, independent component analysis (ICA) and FFT phase image. The JSLT system is used to detect FBHs and the diameter-depth ratio reached 3.33.

engineering, electrical & electronic,instruments & instrumentation,physics, applied
Experimental study on infrared phase-locked thermal imaging inspection of carbon fiber reinforced polymer laminates

Qing-Ju Tang,Juan Ji,Wei-Ming Fan,Ling Ran,Si-Jie An,Tao Zhang,Chi-Wu Bu

DOI: https://doi.org/10.2298/tsci2202105t

IF: 1.971

2022-01-01

Thermal Science

Abstract:Aiming at the debonding defect of carbon fiber reinforced polymer laminates, an infrared phase-locked thermal imaging inspection system was established, and the influence of different defect diameter and depth parameters on the test was analyzed. The principal component analysis algorithm and Karhunen-Loeve Transform algorithm are used to process the image sequence, and the signal-to-noise ratio is calculated. It is concluded that principal component analysis algorithm can improve the image quality more. Gray enhancement and sharpening filter are used to improve the image clarity, thus accurately segmenting the defect features, and realize a clear and intuitive visual image.

thermodynamics
Recent Advances in Active Infrared Thermography for Non-Destructive Testing of Aerospace Components

Francesco Ciampa,Pooya Mahmoodi,Fulvio Pinto,Michele Meo

DOI: https://doi.org/10.3390/s18020609

2018-02-16

Abstract:Active infrared thermography is a fast and accurate non-destructive evaluation technique that is of particular relevance to the aerospace industry for the inspection of aircraft and helicopters' primary and secondary structures, aero-engine parts, spacecraft components and its subsystems. This review provides an exhaustive summary of most recent active thermographic methods used for aerospace applications according to their physical principle and thermal excitation sources. Besides traditional optically stimulated thermography, which uses external optical radiation such as flashes, heaters and laser systems, novel hybrid thermographic techniques are also investigated. These include ultrasonic stimulated thermography, which uses ultrasonic waves and the local damage resonance effect to enhance the reliability and sensitivity to micro-cracks, eddy current stimulated thermography, which uses cost-effective eddy current excitation to generate induction heating, and microwave thermography, which uses electromagnetic radiation at the microwave frequency bands to provide rapid detection of cracks and delamination. All these techniques are here analysed and numerous examples are provided for different damage scenarios and aerospace components in order to identify the strength and limitations of each thermographic technique. Moreover, alternative strategies to current external thermal excitation sources, here named as material-based thermography methods, are examined in this paper. These novel thermographic techniques rely on thermoresistive internal heating and offer a fast, low power, accurate and reliable assessment of damage in aerospace composites.
Nde of Composites Delamination by Infrared Thermography

SL Huang,LM Li,HQ Yang,KR Shi

DOI: https://doi.org/10.1117/12.484090

2003-01-01

Abstract:The principle of infrared thermography is presented briefly. And delamination defects of honeycomb aluminum composites were inspected by infrared thermography technique. Testing result showed that infrared thermography was a rapid, effective nondestructive evaluation method for delamination defects of composite materials. The optimal testing time for different defects was different. And the testing speed was higher than two screens per minute for all delamination defects of honeycomb aluminum composites. Rapid automatic heating modes, automatic synchronous scanning of heating source and infrared detector, and intelligentized defect identification system will be the important developing aspects of infrared thermography testing technique.
A Novel Infrared Thermography Sensing Approach for Rapid, Quantitative Assessment of Damage in Aircraft Composites

Spyridoula Farmaki,Dimitrios A Exarchos,Ilias K Tragazikis,Theodore E Matikas,Konstantinos G Dassios,Dimitrios A. Exarchos,Ilias K. Tragazikis,Theodore E. Matikas,Konstantinos G. Dassios

DOI: https://doi.org/10.3390/s20154113

IF: 3.9

2020-07-24

Sensors

Abstract:The current necessity of the scientific and industrial community, for reduction of aircraft maintenance cost and duration, prioritizes the need for development of innovative nondestructive techniques enabling fast and reliable defect detection on aircraft fuselage and wing skin parts. Herein, a new low-cost thermographic strategy, termed Pulsed Phase-Informed Lock-in Thermography, operating on the synergy of two independent, active infrared thermography techniques, is reported for the fast and quantitative assessment of superficial and subsurface damage in aircraft-grade composite materials. The two-step approach relies on the fast, initial qualitative assessment, by Pulsed Phase Thermography, of defect location and the identification of the optimal material-intrinsic frequency, over which lock-in thermography is subsequently applied for the quantification of the damage’s dilatational characteristics. A state-of-the-art ultra-compact infrared thermography module envisioned to form part of a fully-automated autonomous nondestructive testing inspection solution for aircraft was conceived, developed, and tested on aircraft-grade composite specimens with impact damages induced at variable energy levels and on a full-scale aircraft fuselage skin composite panel. The latter task was performed in semi-automated mode with the infrared thermography module mounted on the prototype autonomous vortex robot platform. The timescale requirement for a full assessment of damage(s) within the sensor’s field of view is of the order of 60 s which, in combination with the high precision of the methodology, unfolds unprecedented potential towards the reduction in duration and costs of tactical aircraft maintenance, optimization of efficiency and minimization of accidents.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation
Generative Independent Component Thermography for Improved Defect Detection of Carbon Fiber Composites

Kaixin Liu,Meili Chen,Zhiwen Wang,Yuan Yao,Jianguo Yang,Yi Liu

DOI: https://doi.org/10.1109/ddcls49620.2020.9275278

2020-11-20

Abstract:As one of the popular techniques for non-destructive evaluation, infrared thermography often requires the assistance of data analysis models to help defect detection and identification. A novel generative independent component thermography (GICT) framework for defect detection in polymer composites is proposed. It utilizes a deep convolutional generative adversarial network to generate more informative images, which enhances the diversity of thermography data. The defect detection performance of sequential ICT-based thermographic data analysis can be enhanced. The feasibility of GICT is illustrated with its application to the defect detection of a carbon fiber reinforced polymer specimen.
Application of the Pulse Infrared Thermography Method for Nondestructive Evaluation of Composite Aircraft Adhesive Joints

Tomáš Kostroun,Milan Dvořák

DOI: https://doi.org/10.3390/ma14030533

IF: 3.4

2021-01-22

Materials

Abstract:In this article, we examine the possibility of using active infrared thermography as a nontraditional, nondestructive evaluation method (NDE) for the testing of adhesive joints. Attention was focused on the load-bearing wing structure and related structural joints, specifically the adhesive joints of the wing spar caps and the skins on the wing demonstrator of a small sport aircraft made mainly of a carbon composite. The Pulse Thermography (PT) method, using flash lamps for optical excitation, was tested. The Modified Differential Absolute Contrast (MDAC) method was used to process the measured data to reduce the effect of the heat source’s inhomogeneity and surface emissivity. This method demonstrated a very high ability to detect defects in the adhesive joints. The achieved results are easy to interpret and use for both qualitative and quantitative evaluation of the adhesive joints of thin composite parts.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering
One-dimensional deep convolutional autoencoder active infrared thermography: Enhanced visualization of internal defects in FRP composites

Yubin Zhang,Changhang Xu,Pengqian Liu,Jing Xie,Yage Han,Rui Liu,Lina Chen

DOI: https://doi.org/10.1016/j.compositesb.2024.111216

IF: 11.322

2024-01-11

Composites Part B Engineering

Abstract:Fiber-reinforced polymer (FRP) composites have been widely applied in different industrial fields, thereby necessitating the employment of non-destructive testing (NDT) methods to ensure structural integrity and safety. Active infrared thermography (AIRT) is a fast and cost-efficient NDT technique for inspecting FRP composites. However, this method is easily affected by factors such as inhomogeneous heating, leading to a low level of visualization of defects. To address this issue, this study proposes a novel method called one-dimensional deep convolutional autoencoder active infrared thermography (1D-DCAE-AIRT) to enhance the visualization of internal defects in FRP composites. This method first preprocesses the thermal image sequence acquired by AIRT inspections. Subsequently, high-level thermal features at the pixel level are extracted from the aforementioned preprocessed thermal image sequence using a designed one-dimensional deep convolutional autoencoder (1D-DCAE) model. Finally, the extracted high-level thermal features are employed to generate enhanced visualization results that exhibit improved defect visibility. The results of three kinds of AIRT (eddy current pulsed thermography, flash thermography, and vibrothermography) experiments on FRP composite specimens with artificially introduced defects show that 1D-DCAE-AIRT can effectively enhance the visualization of internal defects. The enhancement effect is better than the conventional techniques of fast Fourier transform (FFT), principal component analysis (PCA), independent component analysis (ICA), and partial least-squares regression (PLSR).

engineering, multidisciplinary,materials science, composites
The Wrinkles Characterization in GFRP Composites by Infrared Active Thermography

Adam Stawiarski,Małgorzata Chwał,Marek Barski,Marcin Augustyn

DOI: https://doi.org/10.3390/ma16124236

IF: 3.4

2023-06-08

Materials

Abstract:An experimental study has been carried out to assess the effectiveness of infrared thermography in wrinkle detection in composite GFRP (Glass Fiber Reinforced Plastic) structures by infrared active thermography. Wrinkles in composite GFRP plates with different weave patterns (twill and satin) have been manufactured with the use of the vacuum bagging method. The different localization of defects in laminates has been taken into account. Transmission and reflection measurement techniques of active thermography have been verified and compared. The section of a turbine blade with a vertical axis of rotation containing post-manufacturing wrinkles has been prepared to verify active thermography measurement techniques in the real structure. In the turbine blade section, the influence of a gelcoat surface on the effectiveness of thermography damage detection has also been taken into account. Straightforward thermal parameters applied in structural health monitoring systems allow an effective damage detection method to be built. The transmission IRT setup allows not only for damage detection and localization in composite structures but also for accurate damage identification. The reflection IRT setup is convenient for damage detection systems coupled with nondestructive testing software. In considered cases, the type of fabric weave has negligible influence on the quality of damage detection results.

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,metallurgy & metallurgical engineering

Further studies on corticosteroidogenesis. V. 11 Beta-hydroxylation of deoxycorticosterone by mitochondria incubated with malate, supernatant fraction and supernatant fraction+pyruvate+CO2.

Thickness Measurement of Composite Material Using Eddy Current Testing

Fiber orientation assessment in complex shaped parts reinforced with carbon fiber using infrared thermography

Nondestructive Evaluation of Carbon Fiber Bicycle Frames Using Infrared Thermography

Active Infrared Thermography for Interfacial Defects Detection on Composite Cross-Arms Based on Finite Element Simulation

3D photothermal reconstruction of subsurface defects in notched multidirectional CFRP laminates due to tensile fatigue loading

Infrared thermographic inspection of 3D hybrid aluminium-CFRP composite using different spectral bands and new unsupervised probabilistic low-rank component factorization model

Numerical Modelling of the Heat Source and the Thermal Response of an Additively Manufactured Composite during an Active Thermographic Inspection

Independent component thermography for non-destructive testing of defects in polymer composites

A Comparison among Different Ways to Investigate Composite Materials with Lock-In Thermography: The Multi-Frequency Approach

A novel force-temperature model for evaluating internal forces in CFRP by means of infrared thermography

Enhanced Infrared Sparse Pattern Extraction and Usage for Impact Evaluation of Basalt-Carbon Hybrid Composites by Pulsed Thermography

Joint Scanning Laser Thermography Defect Detection Method for Carbon Fiber Reinforced Polymer

Experimental study on infrared phase-locked thermal imaging inspection of carbon fiber reinforced polymer laminates

Recent Advances in Active Infrared Thermography for Non-Destructive Testing of Aerospace Components

Nde of Composites Delamination by Infrared Thermography

A Novel Infrared Thermography Sensing Approach for Rapid, Quantitative Assessment of Damage in Aircraft Composites

Generative Independent Component Thermography for Improved Defect Detection of Carbon Fiber Composites

Application of the Pulse Infrared Thermography Method for Nondestructive Evaluation of Composite Aircraft Adhesive Joints

One-dimensional deep convolutional autoencoder active infrared thermography: Enhanced visualization of internal defects in FRP composites

The Wrinkles Characterization in GFRP Composites by Infrared Active Thermography