Abstract:Water concentration inside proton exchange membrane fuel cells (PEMFCs) is a key factor affecting performance and durability. Therefore, many studies have been conducted to maintain an appropriate moisture balance inside the stack. The most recent study was a study that confirmed moisture distribution using five sensors inside the anode and cathode. However, in this study, it is difficult to determine the exact moisture distribution inside the stack due to insufficient sensors. In this study, a unit cell PEMFC including micro relative humidity and temperature (RH/T) sensors with an active area of 100cm 2 was fabricated to characterize the water concentration. Before installing the micro sensors into the bipolar plates, a reliability test is conducted, and the result shows that the sensor is reliable at 60 °C and 70 °C. After that, for the in-situ temperature and relative humidity measurement, the 50 sensors are installed along the anode and cathode gas channels evenly in the active area. This study investigates the distribution of water transport behavior, temperature, and water concentration at 0.6 V, 0.5 V and 0.4 V of electric load. Dew point is introduced to analyze water concentration, and net water mole flux is calculated to evaluate water transport behavior. The results show that as the load applied to the PEMFC increases, higher temperature band expands from downstream to upstream of the gas flow. In addition, at 0.4 V, observing the highest temperature band between 61 °C to 62 °C, it is concluded that the flow field of the reaction zone is more activated along the downstream. Meanwhile, the anode becomes more dehydrated with higher load and the cathode more hydrated. At 0.4 V, the maximum dew point on the cathode is 37.5 °C, and the minimum dew point on the anode is 30 °C. In conclusion, even though water transports from the cathode to the anode, due to dry inlet gas, 20% of relative humidity, and high flow rate, hydrogen by 2.8lpm and air by 6.65lpm, the anode doesn't become hydrated.

Real-Time Data Acquisition Inside High-Pressure PEM Water Electrolyzer

Flexible Seven-in-One Microsensor Embedded in High-Pressure Proton Exchange Membrane Water Electrolyzer for Real-Time Microscopic Monitoring

Persistent Effect Test and Internal Microscopic Monitoring for PEM Water Electrolyzer

Real-Time Monitoring of the Temperature, Flow, and Pressure Inside High-Temperature Proton Exchange Membrane Fuel Cells

Internal Microscopic Diagnosis of Accelerated Aging of Proton Exchange Membrane Water Electrolysis Cell Stack

In-situ Investigation of Bubble Dynamics and Two-Phase Flow in Proton Exchange Membrane Electrolyzer Cells

Real-time microscopic monitoring of temperature and strain on the surface of magnesium hydrogen storage tank by high temperature resistant flexible integrated microsensor

Experiments and Microsimulation of High-Pressure Single-Cell PEM Electrolyzer

Real-Time Micro-Monitoring of Surface Temperature and Strain of Magnesium Hydrogen Tank through Self-Made Two-In-One Flexible High-Temperature Micro-Sensor

Flexible 5-in-1 Microsensor Embedded in the Proton Battery for Real-Time Microscopic Diagnosis

Investigation on the Microfluidics in PEM Water Electrolyzers

MEMS Based H2 Gas Sensors

A Flexible Integrated Microsensor Embedded in Hydrogen/Vanadium Redox Flow Battery for Real-Time Microscopic Measurement

Design, Fabrication, and Dynamic Environmental Test of a Piezoresistive Pressure Sensor

Highly Sensitive, Flexible MEMS Based Pressure Sensor with Photoresist Insulation Layer.

Multiple in-situ measurement of water transport in the bipolar plate of proton exchange membrane fuel cell

Hydrogen-Bond-Triggered Hybrid Nanofibrous Membrane-Based Wearable Pressure Sensor with Ultrahigh Sensitivity over a Broad Pressure Range.

Exploring and understanding the internal voltage losses through catalyst layers in proton exchange membrane water electrolysis devices

Scalable and Multi-Channel Real-Time Low Cost Monitoring System for PEM Electrolyzers Based on IoT Applications

Development of a Flexible Integrated Self-Calibrating MEMS Pressure Sensor Using a Liquid-to-Vapor Phase Change

Multimodal Single-Entity Electrochemical Fluoride Sensor for Fuel Cell Membrane Degradation Diagnostics