Workshop Sentinel Node 2003

J. Werner

DOI: https://doi.org/10.1007/s00106-003-1038-0

2004-03-01

Abstract:

What problem does this paper attempt to address?

Mechanical Grinding of FeNC Nanomaterial with Fe3O4 to Construct Magnetic Adsorbents for Desulfurization

Chunxia Wang,Wenyi Lu,Wenjie Wu,Lifu Zhang,Wenxuan Guo,Guoyong Huang,Shengming Xu

DOI: https://doi.org/10.1016/j.seppur.2022.122574

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:Herein, a series of 3D nitrogen doped porous carbon nanomaterials (FeNC) at different pyrolysis temperature were prepared, followed by a mechanical grinding method to construct magnetically nanocomposite (FeNC/ Fe3O4) which was demonstrated for the desulfurization of dibenzothiophene (DBT) in model oils. The FeNC derived from the pyrolysis of iron salt and nitrogen-doped carbon precursors possess abundant porous structure, which is highly active in the physical adsorption of aromatic sulfur derivatives. Impressively, the as-prepared FeNC-700 are evidenced to yield an excellent desulfurization efficiency (95.1% for 200 ppmw), a remarkable estimated adsorption capacity (25.08 mg S/g for 200 ppmw), and a high selectivity for DBT. Theoretical calculation revealed that the adsorption behaviors towards DBT followed the pseudo-second-order kinetic model, displays a better fitting coefficient based on Langmuir isotherm equation. The thermodynamics results indicate that adsorption process over FeNC-700 was spontaneous and exothermic reaction since Delta G, Delta H, Delta S, all shows negative signs. Subsequently, the FeNC-700 was mechanically mixed with 20 nm Fe3O4 to produce magnetically nanocomposite (FeNC-700/Fe3O4) for the adsorption of DBT in a simple separation process by external field and can be regenerated five runs without significant weight loss. Therefore, this strategy greatly simplifies the experimental procedure and favors the regeneration of the adsorbents.
Malignant paraganglioma of the mediastinum: a further diagnostic and therapeutic use of radiolabelled mIBG.

E. Cornford,M. Wastie,D. Morgan

DOI: https://doi.org/10.1259/0007-1285-65-769-75

British Journal of Radiology

Abstract:The paraganglia are widely dispersed collections of specialized neural crest cells arising in association with the segmental or collateral autonomic ganglia (Enzinger & Weiss, 1988). The extra-adrenal paraganglia can be best classified by their anatomical site (Glenner & Grimley, 1974). (1) Branchiomeric paraganglia arise in association with the arteries and cranial nerves of the head and neck. Carotid body and glomus jugulare tumours are neoplasms arising from these paraganglia. (2) Intravagal paraganglia are located within the perineurium of the vagus nerve and a vagus body tumour is an example of this type. (3) Aorticosympathetic paraganglia arise in association with the sympathetic nervous system. Aortic body tumours and retroperitoneal paragangliomas are examples of tumours from these paraganglia.
Recent Progress of Metal-Organic Frameworks for Liquid Fuels Desulfurization

Y. Pan,W. Huang,Z.H. Liu,Z.Z. Yang,J.J. Tan,B.M. Xu

DOI: https://doi.org/10.1080/15422119.2024.2367646

2024-06-27

Separation and Purification Reviews

Abstract:With the development of society, environmental protection is receiving increasing attention, and higher requirements have been put forward for the cleanliness of traditional energy sources. Fuels from distilled natural crude oils contain a variety of sulfur-containing compounds, which lead to serious environmental pollution. New technologies for deep desulfurization of fuels are urgently needed to meet the various stringent sulfur standards for liquid fuels (<15 ppm). In recent years, metal-organic frameworks (MOFs) have shown great potential in a variety of applications, especially in fuel desulfurization, such as hydrodesulfurization, oxidative desulfurization, and adsorptive desulfurization, due to their high porosity, high specific surface area and availability. In addition, the combination of MOFs with membranes or ionic liquids also has high desulfurization efficiency. In this review, the applications of MOFs and their composites in fuel desulfurization over the past decade are summarized. The factors affecting the desulfurization performance are pointed, and the desulfurization mechanism is tentatively clarified. Moreover, future recommendations have been discussed briefly.

engineering, chemical,chemistry, analytical, applied
Deep mineralization of VOCs in an embedded hybrid structure CoFe2O4/MoS2/PMS wet scrubber system

Xiai Zhang,Wenquan Zhang,Xinwei Zhang,Jun Li,Tong Wang,Qikui Fan,Hao Zhu,Zhimao Yang,Chuncai Kong

DOI: https://doi.org/10.1016/j.isci.2023.108054

IF: 5.8

2023-09-01

iScience

Abstract:Peroxymonosulfate (PMS)-based advanced oxidation processes in liquid phase systems can actively degrade toluene. In this work, the catechol structural surfactant was introduced to synthesize the dispersed and homogeneous CoFe2O4 nanospheres and embedded into MoS2 nanoflowers to form magnetically separable heterojunction catalysts. The innovative approach effectively mitigated the traditionally low reduction efficiency of transition metal ions during the heterogeneous activation process. In CoFe2O4/MoS2/PMS system, the toluene removal efficiency remained 95% within 2 h. The contribution of SO4⋅-, ·O2-, ·OH, and 1O2 was revealed by radical quenching experiment and electron paramagnetic resonance spectroscopy. The results illustrated that MoS2 offers ample reduction sites for facilitating PMS activation via Fe3+/Fe2+ redox interactions. Furthermore, an investigation into the toluene degradation pathway within the CoFe2O4/MoS2/PMS system revealed its capability to suppress the formation of toxic byproducts. This ambient-temperature liquid-phase method presented promising route for the removal of industrial volatile organic pollutants.

multidisciplinary sciences
Metal-organic Gel Templated Synthesis of Magnetic Porous Carbon for Highly Efficient Removal of Organic Dyes.

Luhuan Wang,Fei Ke,Junfa Zhu

DOI: https://doi.org/10.1039/c5dt04260g

IF: 4

2016-01-01

Dalton Transactions

Abstract:Magnetic porous carbon composites are promising materials in various applications, such as adsorbents, supercapacitors and catalyst supports, due to their high surface area, thermal and chemical stability, and easy separation. However, despite the increasing number of reports of magnetic porous carbon composites, the preparation of these materials with environmentally friendly procedures still remains a great challenge. Herein, we report a facile method to prepare a magnetic porous carbon composite with high surface area from a Fe-based metal-organic gel (MOG) template, an extended structure of a metal-organic framework (MOF). The obtained magnetic porous carbon composite was applied to remove organic dyes from an aqueous solution by selecting methyl orange (MO) as a model molecule. It exhibits excellent adsorption capacity (182.82 mg g(-1)), fast adsorption kinetics (8.13 × 10(-3) g mg(-1) min(-1)), and a perfect magnetic separation performance for the MO removal. This study demonstrates a new way to achieve clean synthesis of magnetic porous carbon materials, and opens a new door for the application of MOGs in organic dye removal.
Cellulose-supported magnetic Fe3O4–MOF composites for enhanced dye removal application

Hailong Lu,Lili Zhang,Baobin Wang,Yunduo Long,Miao Zhang,Jinxia Ma,Avik Khan,Susmita Paul Chowdhury,Xiaofan Zhou,Yonghao Ni

DOI: https://doi.org/10.1007/s10570-019-02415-y

IF: 6.123

2019-04-11

Cellulose

Abstract:Cellulose micro-fibrils (CMF), which are green, sustainable and are made from abundant renewable biomass, have attracted much attention in the research community for various applications. In this study, we presented a novel magnetic cellulose composite catalyst (HKUST-1/Fe3O4/CMF) for pollution remedy purpose. The main function of CMF is to improve the dispersion of metal organic framework (MOF) crystals (HKUST-1) and Fe3O4 nanoparticles (NPs) so that the catalytic performance of resultant HKUST-1/Fe3O4/CMF composite is enhanced. The as-prepared HKUST-1/Fe3O4/CMF catalyst was characterized by TEM, EDX, BET, XRD, FTIR, TGA and VSM analytical techniques. Results have showed that HKUST-1 and Fe3O4 NPs are anchored onto the surface of CMF. The adsorption efficiency of HKUST-1/Fe3O4/CMF composite has enhanced because of the porous MOF structures. Furthermore, the composite catalyst has a large surface area and exhibits good magnetic and catalytic properties in the Fenton system. When used as a catalyst in the degradation of dye model compound (methylene blue, MB), the composite catalyst shows a high catalytic activity. In addition, the composite catalyst reveals a good reusability, durability in the recycling and reuse testing. These results support to conclude that the as-prepared HKUST-1/Fe3O4/CMF composite is a green, sustainable, effective and potential catalyst system for pollutant remedy.

materials science, textiles,polymer science, paper & wood
Structural selective regulation of Fe3O4@C composite as adsorbent for removing different organic pollutants

Luyao Chen,Sen Ren,Kai Mao,Changyuan Yu,Yunfang Liu

DOI: https://doi.org/10.1080/01496395.2024.2366904

IF: 2.799

2024-06-21

Separation Science and Technology

Abstract:Many wastewater treatment methods have been developed because large amounts of organic pollutants (OPs) entered into the water bodies and adsorption is one of the classic and important technologies. Recently, magnetic adsorbents have garnered extensive attention due to the high efficiency and distinctive recyclability. The control of their structures and surface properties is crucial. Here, the magnetite@carbon (Fe 3 O 4 @C) composite was prepared by coupling microreactor and pyrolysis reactor. The structures and surface properties of the Fe 3 O 4 @C were effectively adjusted by changing the pyrolysis temperature and Na 2 CO 3 concentration. The Fe 3 O 4 @C composite prepared at 800°C of pyrolysis temperature with 1 mol·L −1 of Na 2 CO 3 concentration has lipophilicity and the highest adsorption capacity of 92# gasoline among those adsorbents, which is as high as 7.6 g·g −1 . The Fe 3 O 4 @C synthesized at 500°C with 1 mol·L −1 of Na 2 CO 3 concentration has hydrophilicity and the highest adsorption capacity of Rhodamine B and Methyl Blue. The saturated adsorption capacities are about 166 and 301 mg·g −1 , respectively. Fe 3 O 4 @C can be easily separated from wastewater and simply regenerated with less capacity loss after five cycles. The results show that the Fe 3 O 4 @C prepared by this method could be suitable for the removal of different OPs by adjusting the preparation conditions.

engineering, chemical,chemistry, multidisciplinary
Assembly of MOFs/polymer hydrogel derived Fe3O4-CuO@hollow carbon spheres for photochemical oxidation: Freezing replacement for structural adjustment

Lei Qin,Rui Ru,Jingwen Mao,Qin Meng,Zheng Fan,Xiong Li,Guoliang Zhang

DOI: https://doi.org/10.1016/j.apcatb.2020.118754

2020-07-01

Abstract:We report a new strategy for fabrication of magnetic core–shell Fe3O4 hollow sphere derived from MOFs/sodium alginate (SA) hydrogel through one-pot synthesis of ferrocene CVD and pyrolysis. Development of freezing-replacement by n-hexane overcame SA capsule shrink induced by heat-treatment and created highly-stable coconut shell-like superstructures, which allowed active sites homogeneously distributed on no-defect surface and improved magnetic and photocatalytic activity of composites. The turn over frequency (TOF) of Fe3O4 for organic pollutants degradation was 2.3 h-1 under visible light irradiation, much higher than most of reported catalysts. The synergistic effect of bimetallic clusters and carbon matrix facilitated the charge separation and accelerated H2O2 activation to yield high active radicals. Layer structure and good interfacial contact of metallic sites and porous carbon was beneficial for enhancing photocatalytic activity. The progresses offer a feasible route to rational design of MOF-derived hybrid hollow materials with tailored structure and properties for various applications.
Single-atom iron on penta-graphene assisted with non-bonding interaction as superior demercurizer: A DFT exploration

Xiaoshuo Liu,Rui Wang,Tianfang Huang,Xinze Geng,Yifan Xu,Cong Chen,Chongchong Wu,Xunlei Ding,Yufeng Duan

DOI: https://doi.org/10.1016/j.apsusc.2022.153060

IF: 6.7

2022-07-01

Applied Surface Science

Abstract:Elemental mercury (Hg0) released from coal-fired power plants causes global concern. Magnetic adsorbents have attracted extensive attention due to their high adsorption performance, but carbon-based sorbents with magnetism for Hg0 removal are rarely studied. Having excellent adsorption activity, single-atom Fe adsorbents on penta-graphene (PG) substances might be promising magnetic materials for Hg0 removal. In this study, six different PG-based single-atom Fe adsorbents are designed by nitrogen doping, concluding that FeN3 on single-vacancy defective PG (Fe/SVN123) is an effective Hg0 adsorbent due to the larger adsorption energy (−0.87 eV) based on density functional theory (DFT) calculations. The electron density difference (EDD) and density of states (DOS) results demonstrate the existence of chemical bonding between Hg0 and the adsorbents. Non-covalent interaction (NCI) analysis verifies the important contribution of non-bonding interactions to adsorption strength. The temperature has an inhibitory effect on Hg0 adsorption. When the temperature reaches ∼520 K, Hg0 desorbs from Fe/SVN123, leading to adsorbent regeneration. The potentially detrimental effect of SO2 and NO on Hg0 adsorption on Fe/SVN123 is deeply discussed by configuration analysis and ab initio molecular dynamics (AIMD) simulation. This work enriches the fundamentals of single-atom catalysts (SACs) and opens up new insight into non-bonding interactions on SACs.

chemistry, physical,physics, applied, condensed matter,materials science, coatings & films
Defective Silicotungstic acid-loaded magnetic floral N-doped carbon microspheres for ultra-fast oxidative desulfurization of high sulfur liquid fuels

Yefeng Liu,Xiaojie Yin,Chuan Li,Zhong Xie,Fuyan Zhao,Jing Li,Jinpei Hei,Yang Han,Nannan Wang,Peng Zuo

DOI: https://doi.org/10.1039/d3dt03028h

IF: 4

2023-11-03

Dalton Transactions

Abstract:Highly active Keggin-type silicotungstic acid (SiW12) having oxygen vacancies (Ov) defects were encapsulated into the magnetic floral N-doped carbon microspheres (γ-Fe2O3@NC-300) through facile one-step air pyrolysis of the precursor comprising core-shell Fe3O4@polydopamine (Fe3O4@PDA) and SiW12 to prepare γ-Fe2O3@NC@SiW12-300. The fabricated catalysts were characterized systematically and subsequently employed for oxidation desulfurization (ODS) of model fuel. Magnetic floral γ-Fe2O3@NC@SiW12-300 catalyst exhibited nearly perfect catalytic activity, which under mild conditions could remove 100 % amount of 4000 ppm DBT in model fuel within 20 min (0.03 g catalysts and n(H2O2) / n(S) of 2). The catalyst activity is mainly attributed to high activity SiW12 with the Ov defect and its outstanding dispersibility in γ-Fe2O3@NC, along with the high number of exposed active sites. A selected catalyst, γ-Fe2O3@NC@SiW12-300, showed a noticeable turnover frequency (TOF) (110.07 h-1) and lower activation energy (38.79 kJ / mol) in oxidative desulfurization (ODS) with good recyclability. •OH radical was found to be the active species involved in ODS as confirmed by the EPR and scavenger experiments. Additionally, the fabricated catalyst can be conveniently separated and recycled within an externally applied magnetic field.

chemistry, inorganic & nuclear
Ultra‐deep Desulfurization Adsorbents for Hydrotreated Diesel with Magnetic Mesoporous Aluminosilicates

Wangliang Li,Huang Tang,Ting Zhang,Qiang Li,Jianmin Xing,Huizhou Liu

DOI: https://doi.org/10.1002/aic.12070

IF: 4.167

2009-01-01

AIChE Journal

Abstract:Magnetic mesoporous aluminosilicates (MMAS) were synthesized by hydrothermal method and applied as ultra-deep desulfurization adsorbents for hydrotreated diesel. The size of oleic-coated magnetic Fe(3)O(4) nanoparticles prepared by coprecipitation method was about 20 nm. MMAS shows better desulfurization properties for removal of sulfur compounds than NaY and MCM-41. The amount of Fe(3)O(4) nanoparticles has significant effects on specific surface area/pore volume and acidic properties, thus, can affect the desulfurization properties of MMAS. Desulfurization properties of MMAS can be improved with the increase of temperature from 30-70 degrees C and decrease the oil to adsorbent ratio. With the increase of Fe(3)O(4) content, adsorption capacity first increased and then decreased. The sulfur adsorption of MMAS was due to the synergetic effect of strong molecular affinity of the magnetite to the sulfur compound and large surface area/pore volume of the mesoporous aluminosilicates. (C) 2009 American Institute of Chemical Engineers AIChE 56: 1391-1396, 2010
Magnetic Composites Fe 3 O 4 @sio 2 @pils As Sorbents for Efficient Denitrogenation of Fuel Oil

Feng Wang,Jie Li,Long Xu,Feng Jiang,Jianfeng Zhang

DOI: https://doi.org/10.1049/mnl.2019.0245

2019-01-01

Micro & Nano Letters

Abstract:In this work, the study of synthesis and denitrogenation of magnetic polymeric ionic liquids (PILs) for N-compounds in simulated oils and diesel are reported. Three functionalised magnetic particles, Fe3O4@SiO2@PILs with side alkyl chain of C2, C4 and C6, respectively, were prepared by grafting PILs on the surface of silica-coated Fe3O4. Fourier transform infrared spectra, thermogravimetric analysis, X-ray diffraction and scanning electron microscopy were carried out to characterise the structure of Fe3O4@SiO2@PILs. It has shown that Fe3O4@SiO2@ PILs possess precious merits for sorbents, such as regular morphology, good stability and magnetic properties. Denitrogenation experiments of simulated oils demonstrate that Fe3O4@SiO2@ PILs show better denitrogenation efficiency of basic N-compounds than neutral N-compounds. The effects of temperature, reaction times, ratio of reagent to oil on denitrogenation for simulated oils were explored, and 92.1% denitrogenation efficiency was obtained to remove quinoline from simulated oils. Denitrogenation of Fe3O4@SiO2@PILs in diesel leads to 84.3% denitrogenation efficiency, and it can remain 82.5% denitrogenation efficiency after five times of recycles. Compared with other similar sorbents, Fe3O4@SiO2@PILs show competitive performances to eliminate organic N-compounds. It is hopeful that Fe3O4@SiO2@PILs can be promising sorbents for purification of liquid fuel by adsorptive denitrogenation.
Electrospinning fabrication of flexible Fe3O4 fibers by sol-gel method with high saturation magnetization for heavy metal adsorption

Shuying Shi,Chonghe Xu,Xinqiang Wang,Yongshuai Xie,Yuping Wang,Qing Dong,Luyi Zhu,Guanghui Zhang,Dong Xu

DOI: https://doi.org/10.1016/j.matdes.2019.108298

2020-01-01

Abstract:Magnetic fibers adsorbent has attracted more and more attention because of the large surface area and overcoming the disadvantages of easy agglomeration and difficult separation. Adding Fe3O4 nanoparticles into spinning solution followed by electrospinning is a common method to prepare magnetic fibers. In this paper, a new sol-gel method was developed to prepare Fe3O4 fibers, which overcame the disadvantage of low saturation magnetization due to the limited amount of magnetic nanoparticles in spinning solution, and uneven distribution of magnetic nanoparticles in the fibers. Through studying the effect of the proportion of ethanol in the solvent and the amount of solvent on the surface tension, the conductivity and viscosity of the spinning solution, and the spinning solution with the best spinnability were explored. The prepared Fe3O4 fibers had high saturation magnetization and maintained excellent flexibility. They had the advantages of self-supporting without agglomeration, and were easier to magnetically separate than Fe3O4 powder prepared by the same method. In addition, the adsorption and regeneration performances for Pb(II) of Fe3O4 fibers were better than those of Fe3O4 powder. Fe3O4 fibers were suitable for heavy metal adsorbent or adsorbent core, which became another effective strategy to expand the application prospects of magnetic adsorbents.

materials science, multidisciplinary
Magnetically recyclable high-entropy metal oxide catalyst for aerobic catalytic oxidative desulfurization

Peiwen Wu,Chang Deng,Feng Liu,Haonan Zhu,Linlin Chen,Ruoyu Liu,Wenshuai Zhu,Chunming Xu

DOI: https://doi.org/10.1016/s1872-2067(23)64541-3

IF: 16.5

2023-11-24

Chinese Journal of Catalysis

Abstract:High-entropy metal oxide catalysts have demonstrated exceptional performance in activating oxygen for catalytic oxidation reactions. However, ensuring their ease of cyclic usage is crucial to broadening their applications. To address this challenge, a magnetic and recyclable high-entropy metal oxide catalyst is designed and its potential in catalytic oxidative desulfurization of fuel oils with oxygen as the oxidant is also investigated. Through a mechanochemical-assisted calcination method, the magnetic high-entropy metal oxide catalyst (HEMO-900) is successfully synthesized, and the structure of the HEMO-900 catalyst is comprehensively characterized. In addition, it is found that the high-entropy structure facilitates charge modulation of the active components, thereby enhancing the oxygen activation performance. The HEMO-900 catalyst exhibits exceptional oxygen activation ability and catalytic oxidative desulfurization performance, and 96.9% of sulfur removal is achieved under optimal conditions. In addition, it achieves profound desulfurization of various fuel samples by efficiently oxidizing and eliminating diverse aromatic sulfur compounds. Additionally, the catalyst demonstrates outstanding magnetically recyclable properties, enabling rapid separation and recovery from the fuel oil phase through the application of an external magnetic field, making the HEMO-900 catalyst maintained a remarkable sulfur removal efficiency of 91.1% even in the 5 th cycle. Therefore, this magnetically recyclable HEMO-900 catalyst possesses significantly promising research and application prospects in the field of catalytic oxidative desulfurization of fuel oils with oxygen as the oxidant, as well as some other heterogeneous catalysis. Graphical A magnetically recyclable high-entropy metal oxide catalyst was engineered via mechanochemical-assisted calcination method, and the catalyst exhibited excellent performance and magnetically recyclable property in oxidative desulfurization of fuel oils with oxygen as the oxidant. Download : Download high-res image (139KB) Download : Download full-size image

chemistry, physical,engineering, chemical, applied
Magnetically Recyclable 1T-2H MoS2/Fe3O4 Hybrids with Photothermal-promoted Photo-Fenton Catalytic Performance

Yanhua Lei,Mengchao Ding,Sha Cheng,Da Huo,Fei Zhang,Tao Liu,Yuliang Zhang

DOI: https://doi.org/10.1016/j.colsurfa.2023.132117

2023-07-01

Abstract:The transition metal sulfide MoS2 has attracted great interest from the scientific community as an excellent co-catalyst for promoting Fe2+/Fe3+ cycling in advanced oxidation processes to enhance the efficiency of H2O2 decomposition. A photothermal-enhanced photo-Fenton pollutant degradation strategy was proposed. Hybrids of magnetically recyclable Fe3O4 fabricated 1 T-2 H MoS2 (1 T-2 H MoS2 @Fe3O4) with excellent photothermal conversion efficiency were fabricated to overcome the limitations of relatively low catalytic activity and cycling stability in Fenton reaction. XRD, Raman, TEM and hysteresis loop were employed to evaluate the heterogeneous phase 1 T-2 H MoS2 nanoflowers as well as the magnetic property. The 1 T-2 H MoS2 @Fe3O4 hybrids with excellent photothermal conversion efficiency not only enhance the reaction temperature of the Fenton reaction occurring on the material surface, but also demonstrate an effective interfacial photothermal water evaporation efficiency. Due to the synergistic effect of photocatalysis and photo-Fenton catalytic reaction, a quick degradation of simulated pollution were achieved in 5 mins with 98.3% degradation, which could be further improved to 99% due to the photothermal promoting reaction. The 1 T-2 H MoS2 @Fe3O4 hybrids exhibit good magnetic recyclability, cyclic stability and photothermal performance, which endow it a wide potential application in the field of environmental remediation and the field of water evaporation at the photothermal interface, etc.

chemistry, physical
MOF Derived Co−Fe nitrogen doped graphite carbon@crosslinked magnetic chitosan Micro−nanoreactor for environmental applications: Synergy enhancement effect of adsorption−PMS activation

Aiwen Wang,Jiaxin Ni,Wei Wang,Dongmei Liu,Qi Zhu,Binxia Xue,Chein-Chi Chang,Jun Ma,Ying Zhao

DOI: https://doi.org/10.1016/j.apcatb.2022.121926

2022-12-15

Abstract:Adsorption, as a simple and efficient water treatment technology, faces the problem that it can only transfer but not fully mineralize pollutants. Transition metal activated peroxymonosulfate (PMS) exhibit high catalytic activity, but leakage of metal ions poses potential health risks to the environment. To solve these problems, we ingeniously designed a micro−nanoreactor structure with glutaraldehyde crosslinked chitosan as the backbone and encapsulated MOF−derived Co−Fe nitrogen−doped graphitic carbon as the activated PMS reaction center (Co−Fe/NC@GCS). Due to its remarkable adsorption capacity, high concentration sulfamethoxazole could be efficiently enriched through electrostatic attraction and hydrogen bonding, and a small amount of PMS could be rapidly attracted and activated. Meanwhile, the synergistic mechanism of adsorption−PMS activation was also analyzed, and the degradation pathway of sulfamethoxazole was expounded. This study aims to develop a new strategy for the removal of emerging organic pollutants in water with such a system with strong adsorption and catalytic capabilities.
Carbon nanofibers supported sorbents with enhanced performance via microwave-assisted in-situ structural modifications for H 2 S removal

Wenjian Feng,Man Zhang,Xin Zhang,Jie Mi,Chao Yang,Jiancheng Wang,Yu Feng

DOI: https://doi.org/10.1016/j.seppur.2024.127883

IF: 8.6

2024-05-17

Separation and Purification Technology

Abstract:The construction of sorbent with excellent structure and highly dispersed active components is vital to improving its desulfurization activity. Herein, the Fe nanoparticles/carbon nanofibers (Fe/CNFs) desulfurization sorbents were fabricated via electrospinning, template method and microwave carbonization. The structure of sorbents was successfully regulated with the adjustments of Fe content and the types of sacrificial phases. It was found that the Fe content impacted strongly on both structural and desulfurization performance of the sorbents. The sorbents with various Fe contents showed a trend of first increasing and then decreasing with the increased Fe content in breakthrough sulfur capacity. Among the various samples, the sample with the highest sulfur content was 7.21 g S/100 g sorbent. Furthermore, the Fe/CNFs sorbents were optimized via soft and hard template methods, by taking polymethyl methacrylate (PMMA) and SiO 2 nanospheres as sacrificial phases. Desulfurization tests implied that the PMMA and SiO 2 modified sorbents involved sulfur capacity of 13.76 and 14.18 g S/100 g sorbent, respectively. According to the characterizations, the modified sorbents were imparted with micro- and open-type macro-porous structure, respectively, upon which, the active components were uniformly dispersed and exposed. The excellent performance of sorbent could be attributed to the synergistic effect of porous structure and widely distributed Fe nanoparticles on CNFs. This work highlights new strategy for the synthesis of desulfurization sorbent.

engineering, chemical
Synthesis of magnetic carbon composite by diesel engine and its application to dye removal

Abdessadk Anagri,Shin Nishida,Shinsuke Mori,Chihiro Yoshimura,Shunsuke Suzuki

DOI: https://doi.org/10.1080/00986445.2023.2218276

2023-06-03

Chemical Engineering Communications

Abstract:We report a one-step and efficient method to synthesize magnetic diesel particles (MDPs) and their application toward dye removal. The MDPs were obtained by the combustion of ferrocene-doped diesel fuel using an internal combustion engine. The diesel particles combined with ferrocene as a metal source were collected by an electrostatic precipitator. The thermogravimetric analysis confirmed the ferrocene-based catalyst and thermal stability of MDPs. FE-SEM showed irregular and aggregated morphologies, and the presence of iron oxide phases (Fe 4 O 3 and γ-Fe 2 O 3 ) was confirmed by X-ray diffraction analysis. The characteristics of MDPs as an adsorbent for organic pollutants were evaluated by methylene blue (MB) adsorption experiments. Langmuir isotherm and pseudo-second-order models best interpret the adsorption process and kinetics, respectively, with a maximum adsorption capacity of 40.81 mg/g of MB adsorbed on the surface of magnetic diesel particles.

engineering, chemical
Facile Construction of Magnetic Ionic Liquid Supported Silica for Aerobic Oxidative Desulfurization in Fuel

Fujie Liu,Ming Zhang,Yongkang Gao,Haojie Tan,Hongping Li,Chao Wang,Wenshuai Zhu,Huaming Li

DOI: https://doi.org/10.3390/catal11121496

IF: 3.9

2021-12-09

Catalysts

Abstract:With the rapid growth in fuel demand, deep desulfurization of fuel oil is vitally necessary for the sake of health and environmental protection. In this work, a kind of magnetic ionic liquid supported silica is prepared by a facile ball milling method, and applied in the aerobic oxidative desulfurization of organosulfurs in fuel. The experimental results indicated that ball milling procedure can increase the specific surface area of samples, which is beneficial to oxidative desulfurization process. Under the optimal reaction conditions, the prepared materials can have an entire removal of aromatic sulfur compounds as well as a good recycling ability. Moreover, the introduction of Fe3O4 did not decline the desulfurization performance, but help the catalyst to be easily separated after reaction.

chemistry, physical
Microporous Fluorinated MOF with Multiple Adsorption Sites for Efficient Recovery of C 2 H 6 and C 3 H 8 from Natural Gas

Le Yan,Hui-Ting Zheng,Liang Song,Zhang-Wen Wei,Ji-Jun Jiang,Cheng-Yong Su

DOI: https://doi.org/10.1021/acsami.3c15109

IF: 9.5

2024-01-27

ACS Applied Materials & Interfaces

Abstract:Purifying C(2)H(6)/C(3)H(8) from a ternary natural gas mixture through adsorption separation is an important but challenging process in the petrochemical industry. To address this challenge, the industry is exploring effective strategies for designing high-performance adsorbents. In this study, we present two metal-organic frameworks (MOFs), DMOF-TF and DMOF-(CF(3))(2), which have fluorinated pores obtained by substituting linker ligands in the host material. This pore engineering strategy not...

materials science, multidisciplinary,nanoscience & nanotechnology

Workshop Sentinel Node 2003

Mechanical Grinding of FeNC Nanomaterial with Fe3O4 to Construct Magnetic Adsorbents for Desulfurization

Malignant paraganglioma of the mediastinum: a further diagnostic and therapeutic use of radiolabelled mIBG.

Recent Progress of Metal-Organic Frameworks for Liquid Fuels Desulfurization

Deep mineralization of VOCs in an embedded hybrid structure CoFe2O4/MoS2/PMS wet scrubber system

Metal-organic Gel Templated Synthesis of Magnetic Porous Carbon for Highly Efficient Removal of Organic Dyes.

Cellulose-supported magnetic Fe3O4–MOF composites for enhanced dye removal application

Structural selective regulation of Fe3O4@C composite as adsorbent for removing different organic pollutants

Assembly of MOFs/polymer hydrogel derived Fe3O4-CuO@hollow carbon spheres for photochemical oxidation: Freezing replacement for structural adjustment

Single-atom iron on penta-graphene assisted with non-bonding interaction as superior demercurizer: A DFT exploration

Defective Silicotungstic acid-loaded magnetic floral N-doped carbon microspheres for ultra-fast oxidative desulfurization of high sulfur liquid fuels

Ultra‐deep Desulfurization Adsorbents for Hydrotreated Diesel with Magnetic Mesoporous Aluminosilicates

Magnetic Composites Fe 3 O 4 @sio 2 @pils As Sorbents for Efficient Denitrogenation of Fuel Oil

Electrospinning fabrication of flexible Fe3O4 fibers by sol-gel method with high saturation magnetization for heavy metal adsorption

Magnetically recyclable high-entropy metal oxide catalyst for aerobic catalytic oxidative desulfurization

Magnetically Recyclable 1T-2H MoS2/Fe3O4 Hybrids with Photothermal-promoted Photo-Fenton Catalytic Performance

MOF Derived Co−Fe nitrogen doped graphite carbon@crosslinked magnetic chitosan Micro−nanoreactor for environmental applications: Synergy enhancement effect of adsorption−PMS activation

Carbon nanofibers supported sorbents with enhanced performance via microwave-assisted in-situ structural modifications for H 2 S removal

Synthesis of magnetic carbon composite by diesel engine and its application to dye removal

Facile Construction of Magnetic Ionic Liquid Supported Silica for Aerobic Oxidative Desulfurization in Fuel

Microporous Fluorinated MOF with Multiple Adsorption Sites for Efficient Recovery of C 2 H 6 and C 3 H 8 from Natural Gas