Abstract:Significance: Gas in scattering media absorption spectroscopy (GASMAS) enables noninvasive gas sensing in the body. It is developing as a tool for diagnosis and monitoring of respiratory conditions in neonates. Phantom models with relevant features to the clinical translation of GASMAS technology are necessary to understand technical challenges and potential applications of this technique. State-of-the-art phantoms designed for this purpose have focused on the optical properties and anthropomorphic geometry of the thorax, contributing to the source-detector placement, design, and optimization. Lung phantom mimicking the alveolar anatomy has not been included in the existent models due to the inherent complexity of the tissue. We present a simplified model that recreates inflated alveoli embedded in lung phantom. Aim: The goal of this study was to build a lung model with air-filled structures mimicking inflated alveoli surrounded by optical phantom with accurate optical properties (μa = 0.50 cm - 1 and μs'=5.4 cm-1) and physiological parameters [37°C and 100% relative humidity (RH)], and to control the air volume within the phantom to demonstrate the feasibility of GASMAS in sensing changes in pulmonary air volume. Approach: The lung model was built using a capillary structure with analogous size to alveolar units. Part of the capillaries were filled with liquid lung optical phantom to recreate scattering and absorption, whereas empty capillaries mimicked air filled alveoli. The capillary array was placed inside a custom-made chamber that maintained pulmonary temperature and RH. The geometry of the chamber permitted the placement of the laser head and detector of a GASMAS bench top system (MicroLab Dual O2 / H2O), to test the changes in volume of the lung model in transmittance geometry. Results: The lung tissue model with air volume range from 6.89 × 10 - 7 m3 to 1.80 × 10 - 3 m3 was built. Two measurement sets, with 10 different capillary configurations each, were arranged to increase or decrease progressively (in steps of 3.93 × 10 - 8 m3) the air volume in the lung model. The respective GASMAS data acquisition was performed for both data sets. The maximum absorption signal was obtained for configurations with the highest number of air-filled capillaries and decreased progressively when the air spaces were replaced by capillaries filled with liquid optical phantom. Further studies are necessary to define the minimum and maximum volume of air that can be measured with GASMAS-based devices for different source-detector geometries. Conclusions: The optical properties and the structure of tissue from the respiratory zone have been modeled using a simplified capillary array immersed in a controlled environment chamber at pulmonary temperature and RH. The feasibility of measuring volume changes with GASMAS technique has been proven, stating a new possible application of GASMAS technology in respiratory treatment and diagnostics.

Measurement and modeling of oxygen content in a demand constant mass ratio injection rebreather

N2 exchanges in hyperbaric environments: towards a model based on physiological gas transport (O2 and CO2)

Low Pressure Heliox-based Rebreather System to Reduce Work of Breathing and Conserve Gas

A modeling-based evaluation of isothermal rebreathing for breath gas analyses of highly soluble volatile organic compounds

Continuous, Automated and Simultaneous Measurement of Oxygen Uptake and Carbon Dioxide Evolution in Biological Systems

Calibration of a bubble evolution model to observed bubble incidence in divers

Duplicate measures of hemoglobin mass within an hour: feasibility, reliability, and comparison of three devices in supine position

Modeling Pulmonary Gas Exchange and Single-Exhalation Profiles of Carbon Monoxide

Pulse Oximetry Carboxyhemoglobin Saturation Overestimates Carbon Monoxide Rebreathing Derived Measures Of Total Hemoglobin Mass In Healthy Adults

Numerical simulation of the flow and concentration fields for oxygen delivery systems

Lung tissue phantom mimicking pulmonary optical properties, relative humidity, and temperature: a tool to analyze the changes in oxygen gas absorption for different inflated volumes

Measurement of functional residual capacity of the lung by partial CO2 rebreathing method during acute lung injury in animals

Evaluation of a portable, lightweight modular system to deliver high inspired oxygen to trauma casualties without the use of pressurised cylinders

A Lab Assembled Microcontroller-Based Sensor Module for Continuous Oxygen Measurement in Portable Hypoxia Chambers

Continuous aerosol monitoring and comparison of aerosol exposure based on smoke dispersion distance and concentrations during oxygenation therapy

Every Breath You Take: Non-invasive Real-Time Oxygen Biosensing in Two- and Three-Dimensional Microfluidic Cell Models

An Experimental Model of Membraneous Oxygenator

Evaluation of Renal Oxygenation Change under the Influence of Carbogen Breathing Using A Dynamic R-2, R-2 and R-2* Quantification Approach

A New Model of Air–Oxygen Blender for Mechanical Ventilators Using Dynamic Pressure Sensors

Ultrasonic Oxygen Sensor.

Development of clinical tools to estimate the breathing effort during high-flow oxygen therapy: A multicenter cohort study