Abstract:Wake-up receivers (WuRXs) help to significantly reduce the average power of the Internet of the Things (loT) hardware systems. To lower the “asleep” power in the idle state, the WuRX structures based on non-standard protocols have been widely studied in prior researches, which can realize a high sensitivity [1] or low power [2]. Compared to the non-standard receivers, there are more design challenges in the standard-compliant WuRXs. For example, a BLE-compliant WuRX operating in the congested 2.4GHz band should be able to handle potentially large interferers including adjacent-channel tone and image, as well as realize a high sensitivity for long-reach access. Therefore, there have been several conventional solutions for the interference-resilient BLE-compliant WuRXs: 1) Single-path down-conversion WuRXs. The interference is handled by an RF filter [3] or a low-noise LO [4] (Fig. 1, top). The WuRX in [3] utilized an FBAR filter to reject the interference from the adjacent channel, resulting in a signal-to-interference ratio (SIR) of −6dB@2MHz, where the loss of FBAR filter degraded the sensitivity to −85dBm. An LC oscillator based LO was adopted in [4] to suppress the adjacent-channel interference by −10dB, but it's at the penalty of 1.2mW power. 2) I/Q-path down-conversion WuRXs. A Hartley WuRX was designed in [5] to reject both 2MHz adjacent-channel interference and image (Fig. 1, middle), as well as improve the sensitivity to −92dBm, while the I/Q downconverters and LO generators dominated the total power consumption. Although the WuRX power was reduced to 352μW by the edge combiner based I/O LO generation, the SIR was limited to −12.5dB due to the spurs and noise accompanying the LO signal. As a result, it's difficult for the conventional WuRX structures to realize both a high SIR and low power consumption.

Ultra low-power transceiver with novel FSK modulation technique and efficient FSK-to-ASK demodulation

Low-Power, High-Data Rate 915 MHz Transceiver with Fully Passive Wake-Up Receiver for Biomedical Implants

A 11 Mw 2.4 GHz 0.18 Μm CMOS Transceivers for Wireless Sensor Networks

Narrowband FSK Transceiver Circuit for Wireless Power and Data Transmission in Biomedical Implants

A 107 pJ/b TX 260 pJ/b RX Ultralow-Power MEMS-Based Transceiver With Wake-Up in ISM-Bands for IoT Applications

An Ultra-Low Power 400mhz OOK Transceiver for Medical Implanted Applications.

Energy Efficient Transmitters For High Data Rate Biomedical Applications

A Low-Power BFSK Transmitter Architecture for Biomedical Applications

A 400MHz/900MHz Dual-Band Ultra-Low-Power Digital Transmitter for Biomedical Applications

Design of a 0.6-V, 429-MHz FSK Transceiver Using Q-Enhanced and Direct Power Transfer Techniques in 90-nm CMOS

A 400mhz 3–10mbps Transceiver IC with ∼0.3 Nj/bit TX/RX Energy Efficiency for Body Area Applications

A 0.14-nJ/b 200-Mb/s 2.7–3.5-GHz Quasi-Balanced FSK Transceiver With PLL-Based Modulation and Sideband Energy Detection

A 164-$\mu$ W 915-MHz Sub-Sampling Phase-Tracking Zero-IF Receiver With 5-Mb/s Data Rate for Short-Range Applications

An Interference-Resilient 120-Degree-apart Pseudo-I/Q BLE-Compliant Wake-Up Receiver Achieving-21dB SIR,-94dBm Sensitivity, and 4-D Wake-Up Signature

A 164-W 915-MHz Sub-Sampling Phase-Tracking Zero-IF Receiver With 5-Mb/s Data Rate for Short-Range Applications

A Low-Power, High Data-Rate CMOS ASK Transmitter for Wireless Capsule Endoscopy

Low Power High Data Rate Wireless Endoscopy Transceiver.

2.4Ghz 20mb/s FSK Receiver Front-End and Transmitter Modulation PLL Design for Energy-Efficient Short-Range Communicaiton

Ultra-low power, high-data rate, fully on-chip radio frequency on-off keying receiver for internet-of-things applications