Blood procurement in time of disaster.

D. H. Kaump,J. Kasper

Abstract:

What problem does this paper attempt to address?

Characterization of damage mechanisms in CVI-SiC/SiC composite tubes by X-ray tomography

Yang Chen,Lionel Gélébart,Camille Chateau,Michel Bornert,Andrew King,Patrick Aimediue,Cédric Sauder

DOI: https://doi.org/10.48550/arXiv.1710.08309

2017-10-02

Applied Physics

Abstract:SiC/SiC composite tubes are studied as materials for nuclear fuel cladding. A thorough understanding on the mechanisms of damage to this material requires both an experimental and a numerical study. In situ tensile tests were performed under X-ray tomography at the SOLEIL synchrotron. Post processing methods have been developed to analyze the microstructure, measure the deformation and characterize qualitatively and quantitatively the damage mechanisms inside the material. The tomographic images provide 3D descriptions on the microstructure, which are direct input data for the numerical simulation based on FFT. The use of real microstructures makes it possible to combine the simulation results directly with the experimental observations.
In situ X-ray computed micro-tomography imaging of failure processes in Cr-coated Zircaloy nuclear fuel cladding materials

Guanjie Yuan,J. Paul Forna-Kreutzer,Jon Ell,Harold Barnard,Benjamin R. Maier,Edward Lahoda,Jorie Walters,Robert O. Ritchie,Dong Liu,Benjamin Maier

DOI: https://doi.org/10.1016/j.matdes.2023.112373

IF: 9.417

2023-09-01

Materials & Design

Abstract:Chromium (Cr)-coated Zircaloy fuel cladding has been considered a promising candidate materials system for accident tolerant fuels. In this work, two types of Cr coatings produced by cold sprayed (CS) and physical vapour deposited (PVD) methods were studied. In particular, a novel combination of C-ring compression tests at room temperature (RT) and 345 °C in an inert gas environment and real-time X-ray micro-computed tomography (XCT) imaging was adopted to investigate the failure processes. Before testing, the crystal structure and local properties were fully characterized; post testing, ex situ scanning electron microscope (SEM) imaging were conducted to complement the XCT measurements in crack density. It was found that the failure processes in both coatings vary with temperature, as discussed in detail. The hoop strength of first coating cracks’ formation of CS materials were higher than the PVD materials due to their higher interfacial roughness and distribution of splatted grains in CS coating. Based on a calculation of the first Dundurs’ parameter from the measured local properties and observed crack arrest/deflection at coating/substrate interface, it was found that the cold sprayed coating-cladding material system has a higher interfacial toughness in terms of critical strain energy release rate due to its interlocking interfacial structure.

materials science, multidisciplinary
4D synchrotron X-ray microtomography of fracture in nuclear graphite after neutron irradiation and radiolytic oxidation

J. Wade-Zhu,R. Krishna,A.J. Bodey,M. Davies,N.K. Bourne,C. Rau,B. Davies,A. Tzelepi,A.N. Jones,B.J. Marsden,P.M. Mummery

DOI: https://doi.org/10.1016/j.carbon.2020.06.051

IF: 10.9

2020-10-01

Carbon

Abstract:Herein, the first study is presented using 4D synchrotron X-ray microtomography to capture all stages of crack development in neutron irradiated and radiolytically oxidised nuclear graphite. Employing a novel loading setup, specimens of Gilsocarbon graphite, both unirradiated and irradiated at 301 °C to 19.7 × 1020 neutrons/cm2 (∼2.6 displacements/atom (dpa)), were loaded to generate a crack. All stages of the fracture process were then captured using synchrotron X-ray imaging. Reconstructed tomographic images and 3D segmented crack volumes have been used to observe and analyse the irradiation-induced evolution of the graphite microstructure as well as corresponding changes in the crack initiation, propagation, and arrest behaviour of graphite after neutron irradiation. Close examination of the applied stress-strain curves highlights the suppression of micro-crack-based damage accumulation in irradiated graphite. Moreover, as well as the crack-bridging and deflection mechanisms characteristic of unirradiated graphite, crack arrest in the irradiated graphite is shown to be significantly influenced by crack tip blunting. This change is associated with the growth of the open pore structure of graphite, specifically the enlargement and increased frequency of macro-pores, resulting from the simultaneous radiolytic oxidation of the graphite microstructure during neutron irradiation.

materials science, multidisciplinary,chemistry, physical
Advanced Analytics on 3D X-ray Tomography of Irradiated Silicon Carbide Claddings

Fei Xu,Joshua J. Kane,Peng Xu,Jason L. Schulthess,Sean Gonderman,Nikolaus L. Cordesa

2023-03-06

Abstract:Silicon Carbide (SiC) ceramic matrix composite (CMC) cladding is currently being pursued as one of the leading candidates for accident-tolerant fuels. To enable an improved understanding of SiC-SiC composite performance, the development of non-destructive evaluation techniques to assess critical defects is needed. Three-dimensional (3D) X-ray imaging, also referred to as X-ray computed tomography (CT), is a non-destructive, data-rich characterization technique that can provide surface and subsurface spatial information. This paper discusses the design and implementation of a fully automatic workflow to detect and analyze SiC-SiC defects using image processing techniques on 3D X-ray images. The workflow consists of four processing blocks, including data preparation, void/crack detection, visualization, and analysis. In this work, three SiC samples (two irradiated and one unirradiated) provided by General Atomics are investigated. The irradiated samples were exposed in a way that was expected to induce cracking, and indeed, the automated workflow developed in this work was able to successfully identify and characterize the crack formation in the irradiated samples while detecting no observed cracking in the unirradiated sample. These results demonstrate the value of automated XCT tools to better understand the damage and damage propagation in SiC-SiC structures for nuclear applications.

Applied Physics,Materials Science
Distribution of cases according to age and sex Age Sex Cases of retinal vein occlusions Mean SEM Female Male Central occlusions 63

Nursen Aritirk,Y. Oge,D. Erkan,Y. Sullu,F. Mohajery

Abstract:Aims-To evaluate the ocular axial length as a risk factor for development of central retinal vein occlusion (CRVO) and branch retinal vein occlusion (BRVO). Methods-Ocular axial lengths were measured, by A-scan ultrasonography, in 17 patients with CRVO and 41 patients with BRVO and compared with those of contralateral unaffected eyes and 66 age matched controls. Results-In 17 patients with CRVO the mean axial length of affected eyes was 22.25 (SD 0.19) mm and ofunaffected eyes was 22.61 (0.13) mm. In 41 patients with BRVO the mean axial length of affected eyes was 22.89 (0.11) mm and of unaffected eyes was 22.99 (0.12) mm. Conclusion-These findings confirm that the axial lengths in CRVO and BRVO were significantly shorter than in the controls. This significant difference may be a risk factor in the development of CRVO and BRVO. (Br_' Ophthalmol 1996;80:633-636)
Synchrotron Micro-Computed Tomography Analysis of Neutron-Irradiated U-Mo Fuel

Alejandro Figueroa Bengoa,Jonova Thomas,James Hunter,Peter Kenesei,Brandon Miller,Jonathan Almer,Maria A. Okuniewski

DOI: https://doi.org/10.1016/j.jnucmat.2024.155132

IF: 3.555

2024-04-28

Journal of Nuclear Materials

Abstract:The three-dimensional (3D) microstructure of neutron-irradiated uranium-10 wt.% molybdenum (U-10Mo) fuel with a burn-up of 9.8×10 21 fissions/cm 3 was characterized using a novel, multi-modal synchrotron micro-computed tomography approach combining propagation-based phase-contrast enhanced and absorption contrast techniques. The porosity development, porosity interconnectedness, swelling, composition, local thickness of the zirconium (Zr) diffusion barrier, and the influence of the fuel–cladding interaction on the local composition and pore morphology, were uniquely determined in 3D. Two cuboids were produced using a focused ion beam-scanning electron microscope at the Zr diffusion barrier–fuel interface and in the bulk fuel. The bulk fuel sample swelled by 53.3[+9.7/-3.1]%, while the fuel near the Zr–fuel interface swelled by 63.3[+14.7/-7.2]%. The average local thickness of the Zr diffusion barrier decreased by 53%, compared to the expected pre-irradiated thickness. Four pore morphology regions were identified initiating parallel to the fuel–Zr interaction region: (1) an interaction layer of suppressed porosity, (2) a layer of elongated and interconnected porosity, (3) a transition zone of low porosity, and (4) a layer of unoriented porosity representative of the bulk fuel behavior. The increase in porosity near the diffusion barrier corresponded to a higher U concentration compared to that in the bulk fuel. The interconnected porosity in the fuel near the diffusion barrier was extensive and oriented parallel to the diffusion barrier, while the bulk fuel had more compact and isolated pore networks. The interaction layer, despite having suppressed porosity, was nearly 100 wt.% U. Porosity suppression at the diffusion barrier corresponds to the expected reduction in radiation-driven diffusion of Xe at the interface despite the anticipated increase in fission product nucleation originating from a higher U concentration. The novel 3D insights of the porosity, swelling, and compositional variations characterized herein can improve the fidelity of fuel performance codes for proliferation-resistant fuels for research and test reactors.

materials science, multidisciplinary,nuclear science & technology
In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear-fuel cladding material

Guanjie Yuan,J. Paul Forna-Kreutzer,Peng Xu,Sean Gonderman,Christian Deck,Luke Olson,Edward Lahoda,Robert O. Ritchie,Dong Liu

DOI: https://doi.org/10.1016/j.matdes.2023.111784

2023-02-23

Abstract:Silicon carbide (SiC)-based nuclear fission fuel rod cladding has been considered as one of the possible designs for accident tolerant fuels. It is in the form of a SiC fibre reinforced SiC matrix composite tube (SiC f -SiC m ) with monolithic SiC outer and inner coated layers. This study focuses on the deformation and fracture processes in this material using in situ X-ray micro-computed tomography (XCT) at room temperature (RT) and 1200°C in an inert gas environment using a C-ring compression loading configuration. Prior to real-time testing, local properties and residual stresses were characterised using nanoindentation and Raman spectroscopy since they can impact the mechanical behaviour of the material. The 3D strain distribution, crack formation and propagation processes including the toughening mechanisms ( e.g. , crack deflection, micro-cracking, crack bridging and bifurcation) are investigated in the coating and underlying composites at RT and 1200°C. There is no particular sequence which toughening mechanism occurs first – this is very different from the conventional toughening theory in ceramic-matrix composites under uniaxial tension loading. Indeed, no evidence of fibre pull-out or fibre fracture was observed in this SiC f -SiC m nuclear cladding material in the current C-ring compression configuration. The correlation between local measurements and bulk mechanical behaviour are discussed.

materials science, multidisciplinary
Atom probe tomography characterization of high-dose ion irradiated MA957

Jing Wang,Mychailo B. Toloczko,Victor N. Voyevodin,Viktor V. Bryk,Oleg V. Borodin,Valentyn V. Mel'nychenko,Alexandr S. Kalchenko,Frank A. Garner,Lin Shao

DOI: https://doi.org/10.1016/j.jnucmat.2020.152528

IF: 3.555

2021-03-01

Journal of Nuclear Materials

Abstract:<p>Because the microstructure of oxide dispersion strengthened (ODS) alloys largely determines its mechanical properties in nuclear reactors, it is critical to understand the irradiation response of microstructure after high-dose radiation damage for safety and performance concerns. This paper presents a comprehensive characterization of microstructural responses to ion irradiation of the ODS ferritic alloy MA957 using atom probe tomography and compares the observations to current theories on mechanisms for microstructural evolution during irradiation. The MA957 specimens were irradiated by 1.8 MeV Cr<sup>3+</sup> ions to doses and at temperatures relevant to advanced fast reactors (100 dpa and 500 dpa at 400–500°C). The stability of YTiO particles, formation of alpha prime.(α′), and radiation-induced segregation were quantified and analyzed. The results show that the evolution of YTiO particles with respect to dose and temperature is consistent with the Nelson-Hudson-Mazey rate theory model that considers the competing effects of recombination and ballistic dissolution. The formation of Cr-rich precipitates (αʹ) was observed in specimens irradiated at temperatures up to 450°C, and it shows a strong dependence on temperature. Irradiation-induced segregation on grain boundaries was investigated in the 100 dpa specimens. In addition to the commonly studied element Cr, this study also analyzed segregation of Y and Ti. While the magnitude of segregation varies due to intrinsic variability of grain boundary character, clear trends with respect to irradiation temperature were observed. Overall, these results revealed relatively small but distinct effects of irradiation on microstructure evolution to 100 or 500 dpa, demonstrating the excellent radiation tolerance of ODS alloys.</p>

materials science, multidisciplinary,nuclear science & technology
Microstructural characterisation and quantitative evaluation of nuclear graphite grades candidate for Generation-IV nuclear reactors

Marzoqa. M. Alnairi

2019-11-01

Abstract:Nuclear Graphite is a complex material, and its microstructure depends strongly upon the starting materials, manufacturing processes, and operating conditions (Aitkaliyeva, 2017; Heijna et al., 2017; Marsden et al., 2017; Zhou et al., 2017a). Nuclear graphite plays a critical role as a moderator, a neutron reflector, and a core structural component in the operation of old generation reactors, still it is the potential candidates for very high-temperature reactors ((V)HTRs), (Generation-IV reactor). The understanding of nuclear graphite behaviour under irradiation is critical in helping select nuclear graphite grades that offer an enhancement in the safe and economical operation of (V)HTR, and as a basis for core design and safety evaluation. Hence, the experimental work described in this Thesis was designed to quantitatively study the changes in the crystallinity and porosity of virgin and neutron-irradiated nuclear graphite. After neutron irradiation, highly damaged regions (defects) were observed in which the thicknesses reached a few hundred nanometres. Various material characterisation techniques were used to characterise the nuclear graphite samples at various length scales (macroscale, microscale, and nanoscale), including X-ray diffraction (XRD), Raman spectroscopy, polarised light microscopy (PLM), Scanning Electron Microscopy (SEM), and Focussed Ion Beam–Scanning Electron Microscopy (FIB-SEM). PLM and SEM were used to study the changes in the shape and size of the filler particles and porosity in the whole structure, while PLM image analysis facilitated a qualitative and quantitative analysis of domains in different grades of virgin nuclear graphite (PGA, Gilsocarbon, PCEA, and PCIB). For the first time, FIB-SEM was also adopted to study the porosity in 3D of two different virgin nuclear graphite grades (PCEA and PCIB), which are possible candidate materials for (V)HTRs. The data was then compared to the results obtained from PLM and used to build up a 3D view after progressive polishing. As for XRD, it was used to investigate the deformation of the crystal lattice and quantify the build-up of the lattice micro-strains. Raman spectroscopy was performed to evaluate the change in crystallite coherence lengths of virgin and neutron-irradiated graphite, which gave information on the accumulation of defects within the basal plane and the introduction of basal plane fragmentation. The findings of this Thesis enhance current understanding of how the structure of nuclear graphite changes under neutron irradiation using a novel combination of techniques and by improving the use of existing techniques to study the changes in the porosity of nuclear graphite.

Engineering,Physics,Materials Science
Algorithms for TRISO Fuel Identification Based on X-ray CT Validated on Tungsten-Carbide Compacts

Ming Fang,Angela Di Fulvio

DOI: https://doi.org/10.48550/arXiv.2204.13774

2022-04-28

Instrumentation and Detectors

Abstract:Tristructural-isotropic (TRISO) fuel is one of the most mature fuel types for candidate advanced reactor types under development. TRISO-fuel pebbles flow continuously through the reactor core and can be reinserted into the reactor several times until a target burnup is reached. The capability of identifying individual fuel pebbles would allow us to calculate the fuel residence time in the core and validate pebble flow computational models, prevent excessive burnup accumulation or premature fuel discharge, and maintain accountability of special nuclear materials during fuel circulation. In this work, we have developed a 3D image reconstruction and segmentation algorithm to accurately segment TRISO particles and extract the unique 3D distribution. We have developed a rotation-invariant and noise-robust identification algorithm that allows us to identify the pebble and retrieve the pebble ID in the presence of rotations and noises. We also report the results of 200kV X-ray CT image reconstruction of a mock-up fuel sample consisting of tungsten-carbide (WC) kernels in a lucite matrix. The 3D distribution of TRISO particles along with other signatures such as $^{235}$U enrichment and burnup level extracted through neutron multiplicity counting, would enable accurate fuel identification in a reasonable amount of time.
Methodologies for imaging a used nuclear fuel dry storage cask with cosmic ray muon computed tomography

Zhengzhi Liu

DOI: https://doi.org/10.48550/arXiv.1808.07534

2018-08-21

Abstract:Muons interact with matter via two major interaction mechanisms: ionization and radioactive process, and multiple Coulomb scattering leading to energy loss and trajectory deflection, respectively. For a monoenergetic muon beam crossing an object, the scattering angle follows a Gaussian distribution with a zero mean value and a variance that depends on the atomic number of the material object it traversed. Thus, the measured scattering angle may be used to reconstruct the geometrical and material information of the contents inside the dry storage cask. In traditional X-ray computed tomography, the projection information used to reconstruct the attenuation map of the imaged objects is the negative natural logarithm of the transmission rate of the X-rays, which is equal to the linear summation of the X-ray attenuation coefficients along the incident path. Similarly, the variance of the muon scattering angle is also the linear integral of the scattering density of the objects crossed by the muons. Thus, a muon CT image can be built by equating scattering density with attenuation coefficient. However, muon CT faces some unique challenges including: 1) long measurement times due to low cosmic muon flux, 2) insufficiently accurate muon path models, and 3) the inability to precisely measuring muon momentum. In this work, three different muon path models, two different projection methods, and two different reconstruction methods were investigated for use in muon CT of dry storage casks. The investigation was conducted in a validated Geant4 workspace, both in an ideal case and with relevant engineering restrictions considered. The results of these investigations and the expected benefits for fuel cask monitoring are reported herein.

Instrumentation and Detectors,High Energy Physics - Experiment
Evaluation of the Internal Structure of the Multilayer Ceramic Mould for Precision Casting Critical Parts of Aircraft Engines by X-ray Computed Tomography

Tchorz A,Ksiazek M,Krzak I,Szczepaniak-Lalewicz K,Zaba K,Mizera J,Sitek R,Kurdziel P,Dydak A

DOI: https://doi.org/10.4172/2168-9806.1000189

2018-01-01

Journal of Powder Metallurgy and Mining

Abstract:The aim of the study was to present the possibilities of X-ray computed tomography to evaluate the internal discontinuities in multilayer ceramic moulds for precision casting critical parts of aircraft engines. Study for determination of internal discontinuities such as: porosity, micro-cracks and delamination at the ceramic moulds was carried out using the method of X-ray computed tomography. Using this method allowed to obtain a 3D virtual model of the ceramic form and, consequently, the measurement of porosity and thickness both the first layer and the constructional layer in the multilayer ceramic mould. The results are presented possibilities of computer tomography as a tool for microanalysis 3D, identify internal discontinuities and measurement of geometrical size for assessing the quality of ceramic mold in relation to the research of its technological structure.
Detectability by X-ray micro computed tomography of fatigue initiating void defects in laser powder-bed additively manufactured Ti-6Al-4V coupons

Stephen Sun,Jonathan D Miller,Yi Rye Choi,Suzana Turk,Drew Donnelly,Qianchu Liu

DOI: https://doi.org/10.1016/j.addma.2024.103986

IF: 11

2024-02-03

Additive Manufacturing

Abstract:Non-destructive inspection is important for the quality assurance of additively manufactured components. In this study, X-ray micro Computed Tomography (μCT) was assessed for its capabilities and limitations to detect fatigue-initiation porosities in Ti-6Al-4V additively manufactured coupons. Cylindrical coupons were built using laser powder-bed fusion (L-PBF) from three different vendors and four different L-PBF machines that utilized their default process parameters. Using OEM prescribed default process parameters, there was significant variability in the defect distribution between machine to machine and also coupon to coupon that was on the same build plate, primarily due the difference in the internal quality assurance procedures and scan strategies adopted by each vendor. The probability of detection for conventional μCT (cubic voxel size 17.77 μm) was investigated by comparing with what was detected using a Synchrotron Radiation Micro Computed Tomography (SRμCT) at cubic voxel size 5.91 μm. It was found that μCT's detectability relative to SRμCT was approximately 90% for defect diameters of the circumscribed sphere of 230 μm and above and 100% for diameters of 340 μm and above (12–14 times the voxel size of the μCT scan). The type of defect was a key factor to the detectability of large sized defects (>200 μm in diameter) due to the flatness and elongated shape factors. Fatigue results showed the critical defect √Area at the surface was approximately 100 μm at 500 MPa stress level, where significant scatter in fatigue life was observed. Post-fatigue test fractography identified different types of fatigue initiating defects, of which a 'flat' lack-of-fusion type defect was undetectable by either μCT or SRμCT. This type of defect was extremely flat and occupied very little spatial resolution through the build direction which limited the detection by automated threshold-based defect detection algorithms.

engineering, manufacturing,materials science, multidisciplinary
Three-Dimensional Measurement of TRISO Coated Particle Using Micro Computed Tomography

Libing Zhu,Xincheng Xiang,Yahui Peng,Xiangang Wang

DOI: https://doi.org/10.1155/2019/2908538

IF: 0.849

2019-01-01

Science and Technology of Nuclear Installations

Abstract:The fuel safety and performance of high-temperature gas-cooled reactor (HTGR) are dependent on the integrity and geometric parameter of Tri-structural Isotropic (TRISO) coated particle. Micro X-ray computed tomography (CT) was used for nondestructive testing and three-dimensional measurement of the particle components which are composed of kernel, buffer layer, inner pyrolytic carbon layer (IPyC), silicon carbide (SiC) layer, and outer pyrolytic carbon (OPyC) layer. The thickness distribution and volume of kernel and coating layers are obtained by constructing 3D volume rendering of TRISO particle. Mean thickness of each layer is calculated for comparison with design value. A comparison between two-dimensional and three-dimensional measurement results is also made. It is found that the thickness distribution of all layers approximately obeys Gaussian distribution. Deviation of the thickness of kernel and coating layers between 3D measurement result and design value is 7.88%, -25.63%, -45.50%, 13.87%, and 14.73%, respectively. The deviation will affect the failure probability of TRISO particle. Obvious difference of the OPyC mean thickness between 3D measurement and 2D measurement is found, which proves that the proposed 3D measurement provides comprehensive information of the particle. However, 2D and 3D measured thickness of the kernel and IPyC layer tend to be similar.
X-ray microtomography of heavy microstructures: the case of Plasma-Sprayed Tungsten and Tungsten-Steel MMC

A. Zivelonghi,T. Weitkamp,A. Larrue,J-H. You,A.Larrue

DOI: https://doi.org/10.48550/arXiv.1507.07547

2015-07-27

Materials Science

Abstract:In this paper synchrotron microtomography on Plasma Sprayed Tungsten (PS-W) is presented and discussed. PS-W is a challenging material for microtomography since it exhibits a random porous network at different length-scales (from nanometers to micrometers) and is hardly penetrable by X-rays. Furthermore, inner porosity causes strong internal scattering. The key challenges were, firstly, to optimize the beam parameters considering the inherent trade-off between photon energy (penetration depth) and spatial resolution and, secondly, to develop effective signal filtering algorithms. Despite the limited signal-to-noise ratio detected, large volumes of PS-W could be reconstructed with good image quality and micrometric resolution (voxel size = 1.4 {\mu}m). As an important result, we report excellent image quality and higher penetration depth by applying the same setup on a ferrous microstructure, namely a 10%W/Steel MMC used as interlayer between PS-W and a ferritic/martensitic steel substrate. The paper reports a detailed 3D morphological analysis of all inclusion types in PS-W and W/Steel, which led to disclosure of a complex connected porous network in both media. The analysis is presented in terms of multiphase volume fraction, ratio of percolation and 3D shape descriptors. 3D percolation patterns are analyzed in detail and sensitivity towards segmentation threshold for the noise-affected PS-W region is discussed. Remarkably, percolation of the porous phase was found throughout the entire coating thickness of PS-W. In W-Steel MMC percolation was found in the perpendicular plane and interpreted as onset of delamination caused by thermomechanical stress.
Topography changes and microstructural evolution of nuclear graphite (IG-110) induced by Xe 26+ irradiation

He-yao Zhang,Jin-xing Cheng,Jin-liang Song,Hui-qin Yin,Zhong-feng Tang,Zhan-jun Liu,Xiang-dong Liu

DOI: https://doi.org/10.1016/s1872-5805(23)60708-5

IF: 5.7

2023-04-22

New Carbon Materials

Abstract:The microstructure of nuclear graphite, a key material in nuclear reactors, is affected by the high-flux irradiation. The damage to the graphite by irradiation is important for reactor safety. To understand the damage of nuclear graphite by irradiation, IG-110 nuclear graphite, a representative nuclear graphite, was chosen to investigate the change in morphology and microstructure caused by 7 MeV Xe 26+ irradiation with peak damage doses of 0.1-5.0 displacements per atom (dpa) for samples of a size of 40.0 mm×40.0 mm×2.0 mm. The topography and microstructure of IG-110 were characterized by SEM, AFM, grazing incidence XRD, Raman spectroscopy and nano-indentation. Results indicate that after 7 MeV Xe 26+ irradiation at a dose of 0. 11 dpa, a ridge-like structure appears on the surface of the IG-110 graphite, mainly in the binder region, and the surface roughness increases slightly. With a further increase of the irradiation dose, the ridge-like structure also appears in the filler region. At a dose of 0.55 dpa, pore shrinkage increases accompanied by pore closure, and the surface roughness also increases. The changes in topography and microstructure caused by irradiation are attributed to the expansion of graphite along the c-axis direction. With increasing irradiation dose the defect density and the degree of in-plane disorder in the graphene sheets increases, while the modulus and hardness of the graphite first increase and then decrease. Their increase is caused by dislocation pinning and closure of fine pores, while their decrease is attributed to an increase in porosity and the generation of an amorphous structure.

materials science, multidisciplinary
Experimental techniques for investigating thermal transport in nuclear materials

Yuzhou Wang,Yaoyang Zhang,Qiang Zhang,Fei Zhu,Vinay Chauhan,Marat Khafizov,Xianfeng Ma,Zhenqi Chang,Yuzhou WangYaoyang ZhangQiang ZhangFei ZhuVinay ChauhanMarat KhafizovXianfeng MaZhenqi Changa Sino-French Institute of Nuclear Engineering and Technology,Sun Yat-Sen University,Zhuhai,Guangdong,Chinab Technology Development,Intel Corporation,Chandler,AZ,USAc Department of Mechanical and Aerospace Engineering,The Ohio State University,Columbus,OH,USAd School of Nuclear Science and Technology,University of Science and Technology of China,Hefei,Anhui,China

DOI: https://doi.org/10.1080/00223131.2024.2332781

IF: 1.126

2024-03-29

Journal of Nuclear Science and Technology

Abstract:The unique combination of large energy density and extreme environment inside a nuclear reactor imposes strict requirements on the thermal transport property of nuclear materials, which is significantly deteriorated by the irradiation damage, leading to increased service temperature, complex microstructural changes, and compromised integrity. To address this issue, tremendous efforts have been made over the years to measure, comprehend, and enhance thermal transport regulated by radiation-induced defects in advanced nuclear materials. Such efforts would be laborious and time-consuming without revolutionary innovations in characterization techniques. Herein, we review recent experimental studies on the thermal transport properties of nuclear materials, with a focus on the advancements in the measurement techniques with improved spatial resolutions. We provide a brief introduction to the mechanisms of thermal transport in nuclear materials and the impact of irradiation damage on thermal transport. A comprehensive review is presented of advanced thermal characterization techniques that encompass different length scales, ranging from millimeter to nanometer, along with their respective experimental outcomes. Finally, the practicality of each measurement technique is assessed, and research opportunities are discussed in regard to the development of physics-based fuel models.

nuclear science & technology
Nondestructive and fined characterization of injection molded ceramic parts by industrial computed tomography

Hehan Xie,Jie Jiang,Xianfeng Yang,Qinglong He,Zhe Zhou,Xiewen Xu,Li Zhang

DOI: https://doi.org/10.1016/j.ceramint.2019.05.286

IF: 5.532

2019-01-01

Ceramics International

Abstract:Nondestructive testing technology of industrial computed tomography(ICT) is introduced to investigate the injection molded bodies (green body, debinded body and, sintered part) in this study. The results show that ICT can characterize the defects qualitatively and quantitatively by comparing and analyzing the gray distribution of ICT images. The size, numbers and location of pores can be characterized precisely and the density distribution of the green body is quantitatively evaluated. The structure difference and evolution related with processing parameters is also analyzed by this technique. In addition, an image processing method is introduced to three-dimensional reconstruct the two dimensional images after threshold segmentation, and observe the internal structure and spatial morphology of the green body.
Nano-mechanical property assessment of a neutron-irradiated HT-9 steel cladding and a fuel-cladding chemical interaction region of a uranium–10 wt% zirconium nuclear fuel

Jonova Thomas,Fei Teng,Daniel Murray,Maria A. Okuniewski

DOI: https://doi.org/10.1557/s43580-021-00179-x

2021-12-01

MRS Advances

Abstract:Nano-indentation was used in conjunction with electron microscopy to characterize the microstructure and mechanical properties of a neutron-irradiated HT-9 cladding adjoined to uranium–10 wt% zirconium, a fast reactor fuel. Electron microscopy revealed that the neutron-irradiated cladding can be classified into three localities: HT-9 edge, HT-9 + fission products, and the fuel-cladding chemical interaction (FCCI) region. The three localities possessed differing nano-hardness values and consequently resulted in differing calculated yield stresses. Following irradiation, the nano-hardness and yield stresses increased in the HT-9 edge. The HT-9 + fission products locality also increased in nano-hardness and yield stresses with average values similar to the HT-9 edge, but with larger standard deviations due to the diffusion of fission products along grain boundaries. The FCCI locality had the largest and most variable nano-hardness and yield stresses in comparison to the other regions. A yield stress comparison of the HT-9 edge and the literature of neutron-irradiated HT-9 is discussed.Graphical abstract
Application of microtomography and image analysis to the quantification of fragmentation in ceramics after impact loading

Pascal Forquin,Edward Ando

DOI: https://doi.org/10.1098/rsta.2016.0166

2017-01-28

Abstract:Silicon carbide ceramics are widely used in personal body armour and protective solutions. However, during impact, an intense fragmentation develops in the ceramic tile due to high-strain-rate tensile loadings. In this work, microtomography equipment was used to analyse the fragmentation patterns of two silicon carbide grades subjected to edge-on impact (EOI) tests. The EOI experiments were conducted in two configurations. The so-called open configuration relies on the use of an ultra-high-speed camera to visualize the fragmentation process with an interframe time set to 1 µs. The so-called sarcophagus configuration consists in confining the target in a metallic casing to avoid any dispersion of fragments. The target is infiltrated after impact so the final damage pattern is entirely scanned using X-ray tomography and a microfocus source. Thereafter, a three-dimensional (3D) segmentation algorithm was tested and applied in order to separate fragments in 3D allowing a particle size distribution to be obtained. Significant differences between the two specimens of different SiC grades were noted. To explain such experimental results, numerical simulations were conducted considering the Denoual-Forquin-Hild anisotropic damage model. According to the calculations, the difference of crack pattern in EOI tests is related to the population of defects within the two ceramics.This article is part of the themed issue 'Experimental testing and modelling of brittle materials at high strain rates'.

Blood procurement in time of disaster.

Characterization of damage mechanisms in CVI-SiC/SiC composite tubes by X-ray tomography

In situ X-ray computed micro-tomography imaging of failure processes in Cr-coated Zircaloy nuclear fuel cladding materials

4D synchrotron X-ray microtomography of fracture in nuclear graphite after neutron irradiation and radiolytic oxidation

Advanced Analytics on 3D X-ray Tomography of Irradiated Silicon Carbide Claddings

Distribution of cases according to age and sex Age Sex Cases of retinal vein occlusions Mean SEM Female Male Central occlusions 63

Synchrotron Micro-Computed Tomography Analysis of Neutron-Irradiated U-Mo Fuel

In situ high-temperature 3D imaging of the damage evolution in a SiC nuclear-fuel cladding material

Atom probe tomography characterization of high-dose ion irradiated MA957

Microstructural characterisation and quantitative evaluation of nuclear graphite grades candidate for Generation-IV nuclear reactors

Algorithms for TRISO Fuel Identification Based on X-ray CT Validated on Tungsten-Carbide Compacts

Methodologies for imaging a used nuclear fuel dry storage cask with cosmic ray muon computed tomography

Evaluation of the Internal Structure of the Multilayer Ceramic Mould for Precision Casting Critical Parts of Aircraft Engines by X-ray Computed Tomography

Detectability by X-ray micro computed tomography of fatigue initiating void defects in laser powder-bed additively manufactured Ti-6Al-4V coupons

Three-Dimensional Measurement of TRISO Coated Particle Using Micro Computed Tomography

X-ray microtomography of heavy microstructures: the case of Plasma-Sprayed Tungsten and Tungsten-Steel MMC

Topography changes and microstructural evolution of nuclear graphite (IG-110) induced by Xe 26+ irradiation

Experimental techniques for investigating thermal transport in nuclear materials

Nondestructive and fined characterization of injection molded ceramic parts by industrial computed tomography

Nano-mechanical property assessment of a neutron-irradiated HT-9 steel cladding and a fuel-cladding chemical interaction region of a uranium–10 wt% zirconium nuclear fuel

Application of microtomography and image analysis to the quantification of fragmentation in ceramics after impact loading