Abstract:Reinforcement mechanism of short carbon fibers in 3D‐printed short‐continuous carbon fiber reinforced thermoplastic composites. 3D printing of continuous carbon fiber reinforced thermoplastic (C‐CFRTP) composites is a promising fabricating process to achieve complex lightweight structures within a short time; nevertheless, low mechanical performance between printed layers is always a limitation. Adding short carbon fibers during C‐CFRTP fabrication could achieve short‐continuous carbon fiber reinforced thermoplastic (S/C‐CFRTP) composites with enhanced mechanical properties. However, the underlying reinforcement mechanism is not well understood, which hinders the optimization of 3D printing process for S/C‐CFRTP. This paper investigates reinforcing behavior of short carbon fibers and impregnation behavior of the matrix (short carbon fiber reinforced PA6) under various 3D printing conditions. The results indicate that promoting both reinforcing and impregnation behaviors during S/C‐CFRTP 3D printing can improve mechanical performance. As short carbon fiber content increases, the mechanical performance initially experiences enhancement caused by the reinforcing behavior of short fibers, followed by a decline attributed to the insufficient impregnation of the molten matrix. Higher nozzle temperatures facilitate the impregnation behavior of the molten matrix, resulting in superior mechanical performance. Moreover, by leveraging the reinforcement mechanism, the optimal parameter combination is proposed to improve tensile, flexural, and interlaminar shear strengths of the 3D‐printed S/C‐CFRTP to approximately 368.27, 319.80, and 20.09 MPa, respectively. Highlights Reinforcement mechanism is revealed by reinforcing and impregnation behaviors. Short carbon fiber content affects both reinforcing and impregnation behaviors. Beyond 15 wt%, short carbon fiber content shows adverse effects on performance. High nozzle temperature promotes impregnation behavior to improve performance. Optimal parameters raise 19.8% tensile, 39.9% flexural and 161.2% shear strength.

3D printing and modelling of continuous carbon fibre reinforced composite grids with enhanced shear modulus

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Self-monitoring Continuous Carbon Fiber Reinforced Thermoplastic Based on Dual-Material Three-Dimensional Printing Integration Process

Evaluation of Carbon Fiber-Embedded 3D Printed Structures for Strengthening and Structural-Health Monitoring

Carbon Fiber-Thermoplastic Composite 3D Printing Technology and Its Self-Monitoring

3D printing of continuous fiber reinforced cellular structural composites for the study of bending performance

Process evaluation, tensile properties, mathematical models, and fracture behavior of 3D printed continuous fiber reinforced thermoplastic composites

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Effect of infill density and reinforced perimeters on tensile properties and fracture mechanism of 3D printing carbon fiber–reinforced composite

3D printing of continuous carbon fibre reinforced polymer composites with optimised structural topology and fibre orientation

Mechanical Behaviour of 3D Printed Carbon Fibre Reinforced Composite Metastructure with Various Filling Rates

Fabrication of a 3D Printed Continuous Carbon Fiber Composite Grid Stiffened Structure Using Induction Heating

Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fiber Fabrication Technology

Mechanical and interfacial analysis of 3D-printed two-matrix continuous carbon fibre composites for enhanced structural performance

Characterisation and Mathematical Modelling of Nonlinear Mechanical Behaviour of 3D Printed Short Carbon Fibre Reinforced Composites

A Constitutive Model for 3D Printed Continuous Fiber Reinforced Composite Structures with Variable Fiber Content

Evaluation and Prediction of Tensile Properties of 3d‐printed Continuous Carbon/kevlar Fiber‐filled Composites by Coaxial Hybrid Process

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Study on short fiber reinforcement mechanism for mechanical performance improvement of 3D‐printed short‐continuous carbon fiber reinforced thermoplastic composites

High-content continuous carbon fiber reinforced multifunctional prepreg filaments suitable for direct 3D-printing

Effect of Process Parameters on Forming Quality and Flexural Strength of Continuous Fiber Reinforced Cement-Based 3D Printed Composites