Abstract:The best mechanical properties of 3D‐printed CF/PA6 were obtained by varying four printing parameters and using heat press processing. The inherent defects of the layer‐by‐layer manufacturing process limit the mechanical performance of 3D‐printed composite parts. This paper explores a process optimization method for continuous fiber composites 3D printing to improve the mechanical performance of 3D‐printed CF/PA6 (Carbon Fiber/Nylon 6) parts. First, the effects of printing temperature, printing speed, layer thickness, and side step on the mechanical performance of 3D‐printed CF/PA6 were studied by conducting variable parameter printing experiments. All optimal printing parameters for CF/PA6 were obtained, and their impact mechanisms were analyzed. Second, the coupling effect of temperature and pressure of post‐processing reduced the internal voids of 3D‐printed CF/PA6 and improved its mechanical properties. The influence mechanism of the coupling effect of temperature and pressure was summarized, and the optimal post‐processing parameters applicable to CF/PA6 were obtained. Based on the above process optimization, the fiber volume content of the printed CF/PA6 reached 41.05%, and the bending strength and elastic modulus reached 651.54 MPa and 79.08 GPa, which were 209.05% and 179.53% higher than those before optimization. Moreover, the tensile strength and elastic modulus reached 730 MPa and 29.23GPa, which were 98.10% and 81.10% higher than those before optimization. The experimental results give a positive validation of the effectiveness and feasibility of the proposed methodology. Highlights The effects of printing temperature, printing speed, layer thickness, and side step on the mechanical properties of 3D‐printed CF/PA6 were investigated. The optimal printing parameters applicable to CF/PA6 were obtained and their influence mechanisms were analyzed. The effects of the heat press processing method on the internal voids and mechanical properties of 3D‐printed CF/PA6 were investigated, and the optimal post‐processing parameters applicable to CF/PA6 were obtained. The study resulted in optimal printing parameters and post‐processing parameters for 3D printing CF/PA6, which greatly enhanced its tensile and flexural strength and modulus.

3D printing of continuous carbon fibre reinforced polymer composites with optimised structural topology and fibre orientation

Experimental and Theoretical Studies on 3D Printed Short and Continuous Carbon Fiber Hybrid Reinforced Composites

Topology design of 3D printing continuous fiber reinforced structure considering strength and non‐equidistant fiber

Multiscale concurrent design and 3D printing of continuous fiber reinforced thermoplastic composites with optimized fiber trajectory and topological structure

Coupling design and fabrication of continuous carbon fiber-reinforced composite structures using two-material topology optimization and additive manufacturing

3D Printing of Ultrahigh Strength Continuous Carbon Fiber Composites

3D printing of topologically optimized wing spar with continuous carbon fiber reinforced composites

Topology optimization of 3D-printed continuous fiber-reinforced composites considering manufacturability

Manufacturing and 3D printing of continuous carbon fiber prepreg filament

3D printing for continuous fiber reinforced thermoplastic composites: mechanism and performance

Performance-driven 3D printing of continuous curved fibre reinforced polymer composites a preliminary numerical study

Mechanical and interfacial analysis of 3D-printed two-matrix continuous carbon fibre composites for enhanced structural performance

3D printing single‐stroke path planning, local reinforcement and performance testing of MBB beams and cantilever beams

3D printing of continuous fiber reinforced cellular structural composites for the study of bending performance

Research into Specific Mechanical Properties of Composites Produced by 3D-Printing Additive Continuous-Fiber Fabrication Technology

An investigation into mechanical properties of a 3D printed two-matrix continuous fiber composites with multi-cavity structure

Performance enhancement of 3D‐printed carbon fiber‐reinforced nylon 6 composites

Investigation on the mechanical properties of 3D printed hybrid continuous fiber-filled composite considering influence of interfaces

Mechanical Behaviour of 3D Printed Carbon Fibre Reinforced Composite Metastructure with Various Filling Rates

Process evaluation, tensile properties, mathematical models, and fracture behavior of 3D printed continuous fiber reinforced thermoplastic composites

Spatial 3D Printing of Continuous Fiber-Reinforced Composite Multilayer Truss Structures with Controllable Structural Performance