Abstract:A fully inkjet-printed strain sensor based on carbon nanotubes (CNTs) was fabricated in this study for microstrain and microcrack detection. Carbon nanotubes and silver films were used as the sensing layer and conductive layer, respectively. Inkjet-printed CNTs easily undergo agglomeration due to van der Waals forces between CNTs, resulting in uneven films. The uniformity of CNT film affects the electrical and mechanical properties. Multi-pass printing and pattern rotation provided precise quantities of sensing materials, enabling the realization of uniform CNT films and stable resistance. Three strain sensors printed eight-layer CNT film by unidirectional printing, rotated by 180° and 90° were compared. The low density on one side of eight-layer CNT film by unidirectional printing results in more disconnection and poor connectivity with the silver film, thereby, significantly increasing the resistance. For 180° rotation eight-layer strain sensors, lower sensitivity and smaller measured range were found because strain was applied to the uneven CNT film resulting in non-uniform strain distribution. Lower resistance and better strain sensitivity was obtained for eight-layer strain sensor with 90° rotation because of uniform film. Given the uniform surface morphology and saturated sheet resistance of the 20-layer CNT film, the strain performance of the 20-layer CNT strain sensor was also examined. Excluding the permanent destruction of the first strain, 0.76% and 1.05% responses were obtained for the 8- and 20-layer strain sensors under strain between 0% and 3128 με, respectively, which demonstrates the high reproducibility and recoverability of the sensor. The gauge factor (GF) of 20-layer strain sensor was found to be 2.77 under strain from 71 to 3128 με, which is higher than eight-layer strain sensor (GF = 1.93) due to the uniform surface morphology and stable resistance. The strain sensors exhibited a highly linear and reversible behavior under strain of 71 to 3128 με, so that the microstrain level could be clearly distinguished. The technology of the fully inkjet-printed CNT-based microstrain sensor provides high reproducibility, stability, and rapid hardness detection.

Using Electrical Impedance Spectroscopy to Separately Quantify the Effect of Strain on Nanosheet and Junction Resistance in Printed Nanosheet Networks

Strain Induced Modulation of Local Transport of 2D Materials at the Nanoscale

Quantifying the contribution of material and junction resistances in nano-networks

Understanding how junction resistances impact the conduction mechanism in nano-networks

Design of Strain-Limiting Substrate Materials for Stretchable and Flexible Electronics

Printed, Soft, Nanostructured Strain Sensors for Monitoring of Structural Health and Human Physiology

Nanoimprint-induced strain engineering of two-dimensional materials

Straintronics using the monolayer-Xene platform -- a comparative study

A Fully Inkjet-Printed Strain Sensor Based on Carbon Nanotubes

Nano-scale strain engineering of graphene and graphene-based devices

In Situ Measurements of Strain Evolution in Graphene/Boron Nitride Heterostructures Using a Non-Destructive Raman Spectroscopy Approach

Nanoimprint strain-engineering of 2D semiconductors

Fundamental Insights into Graphene Strain Sensing

Inkjet-Printed Multiwalled Carbon Nanotube Dispersion as Wireless Passive Strain Sensor

Elucidating Piezoelectricity and Strain in Monolayer MoS 2 at the Nanoscale Using Kelvin Probe Force Microscopy

A novel electrical depercolation model for stretchable nanocomposite strain sensors

Density Functional Theory of Straintronics Using the Monolayer-Xene Platform: A Comparative Study

Anisotropic Strain-Field-Induced Change of the Electronic Conductivity of Graphene Sheets and Carbon Nanotubes

Asymmetric Behavior in Flexible Piezoelectric Strain Sensors Made of Single Zno Nanowires

Design and Characterization of Flexible Strain Sensors Using Pressure-Sensitive Material with Multi-walled Carbon Nanotubes and Polydimethylsiloxane

1D-2D nanohybrid-based textile strain sensor to boost multiscale deformative motion sensing performance