Abstract:In this study, the change of the resistivity of the CNT-dispersed resin was analyzed by applying a quantum chemical molecular dynamics and the first principle calculation. Various combinations of double-walled carbon nanotube structures were modeled for the analysis. The change of the band structure was calculated by changing the amplitude of the applied strain. It was found in some cases that the band structure changes drastically from a metallic structure to a semiconductive structure, and this result clearly indicated that the electronic conductivity of this MWCNT decreased significantly under tensile strain. It was also found that further application of the strain made a band gap in the band structure. This result indicated that the metallic CNT changes a semiconductive CNT due to the applied strain. The effect of the diameter of the zigzag type CNT on the critical strain of buckling deformation was analyzed under a uni-axial strain. In this analysis, the aspect ratio of each structure was fixed at 10. It was found that the critical strain decreased monotonically with the increase of the diameter. This was because that the flexural rigidity of a cylinder decreased with the increase of its diameter when the thickness of the wall of the cylinder is fixed. It was found that the critical strain decreased drastically from about 5% to 0.5% when the aspect ratio was changed from 10 to 30. Since the typical aspect ratio of CNTs often exceeds 1000, most CNTs show buckling deformation when an axial compressive strain was applied to the CNTs. Finally, the shape of six-membered ring of the CNT was found to be the dominant factor that determines the electronic band structure of a CNT. Next, the change of the band structure of a graphene sheet was analyzed by applying the abinitio calculation (Density functional theory). It was found that the fluctuation of the atomic distance among the six-membered ring is the most dominant factor of the electronic band structure. When the fluctuation exceeded about 10%, band gap appeared in the deformed six-membered ring, and thus, the electronic conductivity of the graphene sheet changes from metallic one to semiconductive one. It is therefore, possible to predict the change of the electronic conductivity of a CNT by considering the local shape of a six-membered ring in the deformed CNT.

Anisotropic Strain-Field-Induced Change of the Electronic Conductivity of Graphene Sheets and Carbon Nanotubes

Thermal Conductivity Of Configurable Two-Dimensional Carbon Nanotube Architecture And Strain Modulation

Nanostructure Dependence of the Electronic Conductivity of Carbon Nanotubes and Graphene Sheets

Multi-Walled Carbon Nanotubes-Based Sensors for Strain Sensing Applications

Strain Sensing: Graphene Reinforced Carbon Nanotube Networks for Wearable Strain Sensors (adv. Funct. Mater. 13/2016)

Superior Piezoresistive Strain Sensing Behaviors of Carbon Nanotubes in One-Dimensional Polymer Fiber Structure

Graphene Reinforced Carbon Nanotube Networks for Wearable Strain Sensors

Directly Correlating the Strain-Induced Electronic Property Change to the Chirality of Individual Single-Walled and Few-Walled Carbon Nanotubes

Structural and Dimensional Engineering of Three-Dimensional Carbon Nanotube/polydimethylsiloxane Composite for Stretchable Sensor

Stretchable MXene/Carbon Nanotube Bilayer Strain Sensors with Tunable Sensitivity and Working Ranges

Anisotropic Structural Carbon Nanotube Aerogels for Piezoresistive Strain Sensors with Multidirectional Sensitivity

Elastomeric Core/Conductive Sheath Fibers for Tensile and Torsional Strain Sensors

Flexible and Stable Carbon Nanotube Film Strain Sensors with Self-Derived Integrated Electrodes

Carbon Nanotube‐Based Strain Sensors: Structures, Fabrication, and Applications

Reinforced standing multi-walled carbon nanotube film for stretchable strain sensor

Ultrathin CNTs Film Based on Marangoni Effect for Strain Sensing Application

Deformable Strain Sensors Based on Patterned Mwcnts/Polydimethylsiloxane Composites

Graphene Welded Carbon Nanotube Crossbars for Biaxial Strain Sensors

A highly sensitive flexible strain sensor based on the contact resistance change of carbon nanotube bundles

Welded Carbon Nanotube–Graphene Hybrids with Tunable Strain Sensing Behavior for Wide-Range Bio-Signal Monitoring

A Fully Inkjet-Printed Strain Sensor Based on Carbon Nanotubes