Abstract:Ti-6Al-4V parts are usually hypothesized as isotropic mechanical properties during micro-machining operation. However, the crystal anisotropic mechanical property is an influential factor in the machining of crystals with different sizes and orientations. The hypothesis causes distinct variation in predicting machining force, and consequently the surface integrity cannot be exactly predicted in the micro-machining. Actually, Ti-6Al-4V parts are pseudo isotropy composed of grains with different orientations, elastic modulus, and hardness. Simultaneously, the initiation mode of plastic slip system varies with the grain orientation when the crystal is subjected to an applied load. It is challengeable to evaluate the effect of crystal orientation on its macroscopic properties, either by traditional experimental methods or macroscopic finite element analysis. Nano-indentation provides one novel method to investigate the plastic deformation of selected grains with specific orientations to characterize their mechanical response properties. This research aims to investigate the plastic behavior of α phase Ti-6Al-4V with different orientation grains by means of nano-indentation experiment and crystal plastic finite element method. In the study, single crystals of α phase are classified into “hard grains” (θ < 30°), “soft grains” (θ > 60°) and “normal grains” (30° < θ < 60°) by defining the crystal inclination angle (θ). The elastic modulus and hardness of hard grains are 9% and 28% larger than those of soft grains, respectively. This difference in mechanical properties depends on the slip system that dominates the plastic deformation behavior. The plastic deformation of soft grains is dominated by prismatic slip (48%), while hard grains are accommodated to plastic deformation by basal slip (51%). The average total cumulative shear strain of the soft grains is double that of the hard grains at a maximum load of 10 mN. Meanwhile, the sensitivity analysis is performed to evaluate the effects of the three sets of < a > slip systems and the two sets of < c + a > slip systems on plastic deformation with different grain orientations. The research contributes to the understanding of the plastic deformation mechanism in micro-machining and the exactly predicting the surface integrity generated from micro-machining.

Orientation reconstruction of transformation $α$ titanium alloys via polarized light microscopy: methodology and assessment

Revealing interface-assisted plastic anisotropy <i>via in situ</i> transmission electron microscopy tension of lamellar TiAl

Effective structural unit analysis in hexagonal close packed alloys -- reconstruction of parent beta microstructures & crystal orientation post processing analysis

Understanding Orientation-Dependent Plasticity in Laser Beam Powder Bed Fusion Stainless Steel Through Crystal Plasticity Modelling

Reorientation-Induced Plasticity (RIP) in Titanium Alloys

In-situ Investigation Via High Energy X-ray Diffraction of Stress-Induced(0002)α→(110)β Transformation in a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr Alloy

Orientation effect on / phase interface mediated deformation mechanism in titanium alloy

Parent beta grain reconstruction of globularized Ti-6Al-4V alloy

A machine learning approach to map crystal orientation by optical microscopy

Crystallographic Origin of Phase Transformation and Lamellar Orientation Control for TiAl-Based Alloys

Influences of Deformation Strain, Strain Rate and Cooling Rate on the Burgers Orientation Relationship and Variants Morphology During Β→α Phase Transformation in a Near Α Titanium Alloy

Identification of Prior Β Grains of Additive Manufactured Ti-6Al-4V Alloy Using Electron Backscatter Diffraction

Precession Electron Diffraction Assisted Characterization of Deformation in Α and Α+β Titanium Alloys

Synergistic and Competitive Mechanisms of Plastic Anisotropy in High-Efficiency Laser Melting Deposited TC11 Alloy

Method for the Detection of Grain Boundaries in α Ti-Based Alloys by means of Polarized Light Microscopy and Image Processing in MATLAB

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy (Adv. Sci. 28/2023)

Quantification of α phase strengthening in titanium alloys: Crystal plasticity model incorporating α/β heterointerfaces

Programming Crystallographic Orientation in Additive‐Manufactured Beta‐Type Titanium Alloy

Investigation on the Crystal Plasticity of Α Phase Ti-6Al-4V Based on Nano-Indentation Simulation and Experiment

Hierarchical Deformation and Anisotropic Behavior of (α+β) Ti Alloys: A Microstructure-Informed Multiscale Constitutive Model Study

Quantification of ? phase strengthening in titanium alloys: Crystal plasticity model incorporating ?/? heterointerfaces