Superconducting Noncontact Device for Precision Positioning in Cryogenic Environments

Jose Luis Perez-Diaz,Ignacio Valiente-Blanco,Efren Diez-Jimenez,Juan Sanchez-Garcia-Casarrubios

DOI: https://doi.org/10.1109/TMECH.2013.2250988

2024-02-01

Abstract:In this paper, a noncontact linear positioner based on superconducting magnetic levitation for high-precision positioning has been tested under cryogenic conditions

Applied Physics

What problem does this paper attempt to address?

Improving Resolution and Run Outs of a Superconducting Noncontact Device for Precision Positioning

I. Valiente-Blanco,E. Diez-Jimenez,J. Sanchez-Garcia-Casarrubios,J. L. Perez-Diaz

DOI: https://doi.org/10.1109/TMECH.2014.2351493

2024-02-01

Abstract:This paper describes the improvement of the performance of a long-stroke high-precision positioning slider suitable for cryogenic environments due to the application of a set of design rules given in a previous paper. The device, based on superconducting magnetic levitation, is self-stable and does notmake contact between the slider and the guideline, avoiding tribological and lubrication problems associated with cryogenics.

Applied Physics
Engineering and performance of a contactless linear slider based on superconducting magnetic levitation for precision positioning

Ignacio Valiente-Blanco,Efren Diez Jimenez,Jose Luis Perez-Diaz

DOI: https://doi.org/10.1016/j.mechatronics.2013.07.011

2024-02-01

Abstract:In this paper, a contactless linear slider for precision positioning able to operate in cryogenic environments is presented. The device, based on superconducting magnetic levitation, does not present contact between the slider (composed of a permanent magnet) and the guideline (made of high-temperature superconducting disks) of the mechanism, thereby avoiding any tribological problems. Moreover, the slider is self-stable and the superconductors provide inherent guidance to the permanent magnet in the sliding DoF due to the high translational symmetry of the magnetic field that leads to low power consumption. A sub-micrometre resolution and a symmetric stroke over 9 mm have been demonstrated at cryogenic temperatures. In addition, a set of design rules for this kind of mechanism has been proposed and experimentally validated. These rules demonstrate that the performance of the device can be tuned just by modifying some geometrical parameters of the mechanism. In this way, the sensitivity and stiffness, resolution, angular run outs and power consumption can be adjusted for different applications and requirements.

Applied Physics
Non-contact linear slider for cryogenic environment

Jose-Luis Perez-Diaz,Juan Carlos Garcia-Prada,Efren Diez-Jimenez,Ignacio Valiente-Blanco a,Berit Sander,Lauri Timm,Juan Sanchez-Garcia-Casarrubios,Javier Serrano,Fernando Romera,Heribert Argelaguet-Vilaseca,David Gonzalez-de-Maria

DOI: https://doi.org/10.1016/j.mechmachtheory.2011.09.002

2024-02-01

Abstract:A non-contact linear slider based on stable superconducting magnetic levitation with a long permanent magnet as a slider and two fixed superconducting disks which define the slide way has been designed, built and tested. The slider can be moved stably along a stroke of 11.5mm by supplying a low current in a coil located at the end of the stroke while the levitation remains stable providing a reliable mechanism for linear displacement in a cryogenic environment. The response is linear with a sensitivity of 52 {\mu}m/mA for displacements lower than 6 mm. Run out, pitch, yaw and roll have been measured demonstrating an overall good performance. In all cases the measured hysteresis was lower than 250 {\mu}m and the measured run out was also lower than 250 {\mu}m both for Y and Z axis. Roll and yaw were always below 300 {\mu}rad, that is one order of magnitude lower than the pitch (4500 {\mu}rad).

Applied Physics
A compact inertial nano-positioner operating at cryogenic temperatures

Pritam Das,Sulagna Dutta,Krishna K.S.,John Jesudasan,Pratap Raychaudhuri

2024-09-24

Abstract:Nano-positioning plays a very important role in applications such as scanning probe microscopy and optics. We report the development of a compact inertial nanopositioner along with fully computer interfaced electronics operating down to 2 K, and its use in our fully automated needle-anvil type Point Contact Andreev Reflection (PCAR) apparatus. We also present the fully automated operational procedures using LabVIEW interface with our home-built electronics. The point contact spectroscopy probe has been successfully used to perform PCAR measurements on elemental superconductors at low temperatures. The small footprint of our nano-positioner makes it ideally suited for incorporation in low temperature scanning probe microscopes and makes this design versatile for various research and industrial purposes.

Instrumentation and Detectors,Materials Science,Superconductivity
Dynamics of a Superconducting Linear Slider

I. Valiente-Blanco,J.L. Perez-Diaz,E. Diez-Jimenez

DOI: https://doi.org/10.1115/1.4028928

2024-02-01

Abstract:In this paper, the dynamic behavior of a one degree-of-freedom (DOF) contactless linear slider based on superconducting magnetic levitation is experimentally analyzed. The device is intended for precision positioning of an optic mirror in cryogenic environments. Different prototypes of this device have been tested at cryogenic temperatures (77 K), and their mechanical behavior characterized in the sliding direction for forced and unforced oscillations. Experimental results reveal that the slider is self-stable at the initial equilibrium position and the dynamic behavior fits well an underdamped harmonic oscillator. Finally, the device showed great potential for horizontal vibration isolation, acting as a low-pass filter with a resonance at about 0.9 Hz

Applied Physics
Novel cryogenic motion control for aerospace

Cao Zhitong,Chen Hongping,He Guoguang,Cai Jiongjiong

DOI: https://doi.org/10.1016/b978-008044559-5/50097-1

2005-01-01

Abstract:In this paper two types of novel cryogenic mechanisms are exhibited, which has been designed using high-temperature superconducting (HTS) and magnetostrictive materials. Magnetostrictive materials have lead to a variety of large-stroke, high-force actuators at cryogenic temperature, which was previously difficult to make and is now much easier. Using HTS tapes in magnet takes advantage of the cryogenic temperature environment for added motive efficiency. Innovative actuator or motor designs using HTS magnet with the application of specific drive electronics bring out efficient, compact, and lightweight actuator systems for aerospace.
Cryogenic Test Stand for Characterization of Magnetocaloric Materials

Carlos Hernando Lpez de Toledo,Javier Munilla,Luis Garca-Tabars,Juan Carlos del Real,Ivn Castro,Luis Gonzlez,Fernando Toral,Carlos Hernando,Luis García-Tabarés,Iván Castro,Luis González

DOI: https://doi.org/10.1109/tasc.2024.3370126

IF: 1.9489

2024-01-01

IEEE Transactions on Applied Superconductivity

Abstract:Alternative cryogenic refrigeration methods are needed to improve the low efficiency of traditional gas cycles cryocoolers. Magnetic refrigeration is an old known technique used to reach below Kelvin temperatures, though there is rising interest in using this method at liquid helium and liquid hydrogen temperatures due to its high Carnot efficiency. However, further experimentation is needed to fully understand the heat transfer dynamics of magnetocaloric materials at cryogenic temperatures. A test stand has been designed to evaluate the heat transfer coefficients of these materials using the single-blow transient test technique. The system consists of a hermetic helium gas circuit, which is cooled down to cryogenic temperatures and is forced to flow through a packed bed of magnetocaloric material. In order to test the heat transfer properties of the magnetocaloric materials at different magnetic fields the test stand has a superconducting solenoid capable of providing up to 4 T. The design and validation of the test stand for the characterization of magnetocaloric materials is described in the present paper.

physics, applied,engineering, electrical & electronic
Levitation Force of Small Clearance Superconductor–magnet System under Non-Coaxial Condition

Jimin Xu,Yingze Jin,Xiaoyang Yuan,Xusheng Miao

DOI: https://doi.org/10.1142/s0217984917500750

2017-01-01

Modern Physics Letters B

Abstract:A novel superconducting tilting-pad bearing was proposed for the advanced research of reusable liquid hydrogen turbopump in liquid rocket. The bearing is a combination of superconducting magnetic bearing and hydrodynamic fluid-film bearing. Since the viscosity of cryogenic fuel to activate superconducting state and form hydrodynamic fluid-film is very low, bearing clearance will be very small. This study focuses on the investigation of superconducting levitation force in this kind of small clearance superconductor–magnet system. Based on Bean critical state model and three-dimensional finite element method, an analysis method is presented to obtain the levitation force under such situation. Since the complicated operational conditions and structural arrangement for application in liquid rocket, center lines of bulk superconductor and magnet rotor will usually be in non-coaxial state. Superconducting levitation forces in axial direction and radial direction under non-coaxial situation are also analyzed by the presented method.
Cryogenic optical beam steering for superconducting device calibration

K. Stifter,H. Magoon,A. J. Anderson,D. J. Temples,N. A. Kurinsky,C. Stoughton,I. Hernandez,A. Nuñez,K. Anyang,R. Linehan,M. R. Young,P. Barry,D. Baxter,D. Bowring,G. Cancelo,A. Chou,K. R. Dibert,E. Figueroa-Feliciano,L. Hsu,R. Khatiwada,S. D. Mork,L. Stefanazzi,N. Tabassum,S. Uemura,B. A. Young

2024-05-04

Abstract:We have developed a calibration system based on a micro-electromechanical systems (MEMS) mirror that is capable of delivering an optical beam over a wavelength range of 180 -- 2000 nm (0.62 -- 6.89 eV) in a sub-Kelvin environment. This portable, integrated system can steer the beam over a $\sim$3 cm $\times$ 3 cm area on the surface of any sensor with a precision of $\sim$100 $\mu$m, enabling characterization of device response as a function of position. This fills a critical need in the landscape of calibration tools for sub-Kelvin devices, including those used for dark matter detection and quantum computing. These communities have a shared goal of understanding the impact of ionizing radiation on device performance, which can be pursued with our system. This paper describes the design of the first-generation calibration system and the results from successfully testing its performance at room temperature and 20 mK.

Quantum Physics,High Energy Physics - Experiment
Low temperature and high magnetic field performance of a commercial piezo-actuator probed $via$ laser interferometry

R. Adhikari,K. Doesinger,P. Linder,B. Faina,A. Bonanni

DOI: https://doi.org/10.1063/5.0034569

2020-10-22

Abstract:The advances in the fields of scanning probe microscopy, scanning tunneling spectroscopy, point contact spectroscopy and point contact Andreev reflection spectroscopy to study the properties of conventional and quantum materials at cryogenic conditions have prompted the development of nanopositioners and nanoscanners with enhanced spatial resolution. Piezoelectric-actuator stacks as nanopositioners with working strokes $>100~\mu\mathrm{m}$ and positioning resolution $\sim$(1-10) nm are desirable for both basic research and industrial applications. However, information on the performance of most commercial piezoelectric-actuators in cryogenic environment and in the presence of magnetic fields in excess of 5\,T is generally not available. In particular, the magnitude, rate and the associated hysteresis of the piezo-displacement at cryogenic temperatures are the most relevant parameters that determine whether a particular piezoelectric-actuator can be used as a nanopositioner. Here, the design and realization of an experimental set-up based on interferometric techniques to characterize a commercial piezoelectric-actuator over a temperature range of $2~\mathrm{K}\leq{T}\leq260~\mathrm{K}$ and magnetic fields up to 6\,T is presented. The studied piezoelectric-actuator has a maximum displacement of $30~\mu\mathrm{m}$ at room temperature for a maximum driving voltage of 75\,V, which reduces to $1.2~\mu\mathrm{m}$ with an absolute hysteresis of $\left(9.1\pm3.3\right)~\mathrm{nm}$ at $T=2\,\mathrm{K}$. The magnetic field is shown to have no substantial effect on the piezo properties of the studied piezoelectric-actuator stack.

Materials Science
A simple method to measure the temperature and levitation height of devices rotating at cryogenic temperatures

Paolo de Bernardis,Fabio Columbro,Silvia Masi,Alessandro Paiella,Giovanni Romeo

DOI: https://doi.org/10.1063/5.0005498

2020-04-01

Abstract:We describe a simple system to measure the temperature and levitation height of levitating cryogenic devices in rotation. Devices of this kind are the half-wave-plates rotating on superconducting magnetic bearings used in several cryogenic polarimeters for the cosmic microwave background. The temperature measurement is important to monitor the radiative background and potential systematic effects in the polarimeter. In our implementation, the temperature sensor is a thermistor, physically mounted on the rotating device. The sensor is biased with an AC current, which is transferred from the stationary electronics to the rotating device via capacitive coupling. The levitation height sensor is a network of capacitors, similar to the one used for the capacitive coupling of the thermistor. We describe the optimization of the readout system and its performance, which has been tested on a room-temperature prototype. We show that this system reaches an accuracy better than 3% for the measurement of the thermistor resistance and an accuracy of ∼10 μm for the measurement of its levitation height.
Fabrication of Nbti Superconducting Joint by Electromagnetic Forming Method

Jun Sheng Cheng,Feng Zhou,Lan Kai Li,Chun Yan Cui,Wan Shuo Sun,Yin Ming Dai,You Tong Fang

DOI: https://doi.org/10.1109/asemd.2015.7453649

2015-01-01

Abstract:The electrical jointing of superconducting wires / tapes is a key issue for the construction of the scientific superconducting magnet that required high field stability, such as NMR, FTICR-MS and some inertial navigators. In this paper, the preliminary experiment of electromagnetic formed NbTi superconducting joint was done. The fabrication technique was researched by changing the parameters. The joint resistances were tested in liquid helium using coil current decay method. The contact resistance properties of the superconducting joint were investigated. The plastic deformation and the electrical contact characteristics of the NbTi superconducting joint were discussed. The results show that the electromagnetic formed NbTi superconducting joint has the excellent low-resistance property and good repeatability.
Cryogen free spin polarized scanning tunneling microscopy and magnetic exchange force microscopy with extremely low noise

Haiming Huang,Mingming Shuai,Yulong Yang,Rui Song,Yanghui Liao,Lifeng Yin,Jian Shen

DOI: https://doi.org/10.1063/5.0095271

2022-07-01

Abstract:Spin polarized scanning tunneling microscopy (SP-STM) and magnetic exchange force microscopy (MExFM) are powerful tools to characterize spin structure at the atomic scale. For low temperature measurements, liquid helium cooling is commonly used, which has the advantage of generating low noise but has the disadvantage of having difficulties in carrying out measurements with long durations at low temperatures and measurements with a wide temperature range. The situation is just reversed for cryogen-free STM, where the mechanical vibration of the refrigerator becomes a major challenge. In this work, we have successfully built a cryogen-free system with both SP-STM and MExFM capabilities, which can be operated under a 9 T magnetic field provided by a cryogen-free superconducting magnet and in a wide temperature range between 1.4 and 300 K. With the help of our specially designed vibration isolation system, the noise is reduced to an extremely low level of 0.7 pm. The Fe/Ir(111) magnetic skyrmion lattice is used to demonstrate the technical novelties of our cryogen-free system.
High-Q magnetic levitation and control of superconducting microspheres at millikelvin temperatures

Joachim Hofer,Rudolf Gross,Gerard Higgins,Hans Huebl,Oliver F. Kieler,Reinhold Kleiner,Dieter Koelle,Philip Schmidt,Joshua A. Slater,Michael Trupke,Kevin Uhl,Thomas Weimann,Witlef Wieczorek,Markus Aspelmeyer

DOI: https://doi.org/10.1103/PhysRevLett.131.043603

2023-08-01

Abstract:We report the levitation of a superconducting lead-tin sphere with 100 micrometer diameter (corresponding to a mass of 5.6 micrograms) in a static magnetic trap formed by two coils in an anti-Helmholtz configuration, with adjustable resonance frequencies up to 240 hertz. The center-of-mass motion of the sphere is monitored magnetically using a dc superconducting quantum interference device as well as optically and exhibits quality factors of up to 2.6e7. We also demonstrate 3D magnetic feedback control of the sphere's motion. The setup is housed in a dilution refrigerator operating at 15 millikelvin. By implementing a cryogenic vibration isolation system we can attenuate environmental vibrations at 200 hertz by approximately seven orders of magnitude. The combination of low temperature, large mass and high quality factor as well as adjustable resonance frequencies provides a promising platform for testing quantum physics in previously unexplored regimes with high mass and long coherence times.

Quantum Physics
A superconducting quantum interference device based read-out of a subattonewton force sensor operating at millikelvin temperatures

O. Usenko,A. Vinante,G. Wijts,T. H. Oosterkamp

DOI: https://doi.org/10.1063/1.3570628

IF: 4

2011-03-28

Applied Physics Letters

Abstract:We present a scheme to measure the displacement of a nanomechanical resonator at cryogenic temperature. The technique is based on the use of a superconducting quantum interference device to detect the magnetic flux change induced by a magnetized particle attached on the end of the resonator. Unlike conventional interferometric techniques, our detection scheme does not involve direct power dissipation in the resonator, and therefore, is particularly suitable for ultralow temperature applications. We demonstrate its potential by cooling an ultrasoft silicon cantilever to a noise temperature of 25 mK, corresponding to a subattonewton thermal force noise of 0.5 aN/Hz.

physics, applied
A New Magnetically Levitated Positioning Stage with Nanometer Resolution

Hao Xiaohong,Mei Xuesong,Zhang Dongsheng

2009-01-01

Abstract:To realize high speed and high precision positioning for photolithography,a novel scheme of magnetically levitated nanometer positioning stage was proposed.This stage uses 4 electromagnetic coils as the stator and 32 permanent magnets as the mover.The levitation and linear drive parts of the stage are separated,so that the coupling between them is minimized and the nonlinearity caused by ferromagnetic material is avoided.A dynamical model in levitation direction was built,and a H∞ robust controller was designed using mixed sensitivity control.Then the dynamic responses were simulated.The simulation results show that the positioning stage has the advantages of better stability,rapid response and ultra precision positioning.This system provides 15 nm-positioning accuracy over the total range of 0.5 μm along the vertical direction.It can be applied to the field of semiconductor manufacturing for photolithography requiring ultra precision positioning and super cleanness.
Design And Detection Of Super-Precision Positioning Stage With Nanometer Resolution

Chunyong Yin,Dejiao Lin,Jian Wu,Rui Zhang

DOI: https://doi.org/10.1117/12.447317

2001-01-01

Abstract:A precision positioning system with a high displacement resolution has been widely required for modem industrialized applications, such as microelectronics, super-precision manufacturing, etc. This paper discusses the design and the features of a new piezodriven precision micro positioning stage utilizing flexure hinges. Theoretical analysis for the stiffness of the flexure hinge is also given briefly. A piezoelectric ceramic(PZT) is applied to chive the precision stage, whose displacement can reach 5 mum when employed with 1000 voltage power. In order to testify the robust and measurement stability of the precision stage, three kinds of PZT produced in Germany. Japan and China respectively are utilized. A dual-frequency interferometer with nanometer resolution and accuracy is adopted to evaluate the mechanical characteristics of the positioning stage. The experimental result shows that the open loop control of the stage provides 0.2nm positioning resolution along the moving direction.
A 1-2 K Cryogenic System with Light Weight, Long Life, Low Vibration, Low EMI and Flexible Cooling Capacity for the Superconducting Nanowire Single-Photon Detector

Haizheng Dang,Han Tan,Tao Zhang,Rui Zha,Jun Tan,Yongjiang Zhao,Bangjian Zhao,Renjun Xue,Jiaqi Li

DOI: https://doi.org/10.1109/tasc.2021.3060357

IF: 1.9489

2021-01-01

IEEE Transactions on Applied Superconductivity

Abstract:This paper presents a 1-2 K cryogenic system for cooling the superconducting nanowire single-photon detector (SNSPD). The system is based on the Stirling-type pulse tube cryocooler (SPTC) and the Joule-Thompson (JT) cryocooler technologies and thus named as the hybrid cryogenic system. It eliminates any moving component at the cold end which endows it with evident advantages over the Gifford-McMahon (GM) cryocooler in terms of low vibration, low electromagnetic interference (EMI) and long life. It can operate at 1-2 K and has an expected mean-time-to-failure of 10 years. The overall weight is below 30 kg, which makes it an attractive cryocooler candidate for the space applications. Furthermore, the operating temperature can be adjusted conveniently for the SNSPD other than being at a fixed temperature as the superfluid helium does. The design approaches and system integration are described in detail, and the performance characteristics presented and discussed. The cooling system has an experimental cooling temperature of 1.52 K. It is also expected to reach 1 K and below provided that the further performance improvement is conducted.
Cryogenic Goniometer for Measurements in Pulsed Magnetic Fields Fabricated Via Additive Manufacturing Technique

Ximone Willis,Xiaxin Ding,John Singleton,Fedor F. Balakirev

DOI: https://doi.org/10.1063/1.5125792

IF: 1.6

2020-01-01

Review of Scientific Instruments

Abstract:Complex high-precision mechanical devices can be fabricated using a three-dimensional printing technology with the help of computer-aided design. Using 3D stereolithography, we have constructed a cryogenic goniometer for measurements in pulsed magnetic fields of up to 100 T, at temperatures as low as 0.5 K. We review the properties of several materials tested in developing the goniometer and report on its design and performance. The goniometer allows samples to be rotated in situ to a precision of 0.2° so that the field can be applied at many different angles to the samples' symmetry directions. Following its success, we establish that 3D printing is now a viable technology for pulsed field and other cryogenic probes.
An In-Situ Movable Calibration Source for Cryogenic Particle Detectors

N. Mast,M. Fritts,D. Sincavage,P. Cushman,V. Mandic

DOI: https://doi.org/10.1016/j.nima.2020.164070

2020-04-29

Abstract:A prototype device capable of moving a radioactive calibration source to multiple positions was operated at millikelvin temperatures using a modified commercial stepper motor. It was developed as an in-situ calibration strategy for cryogenic dark matter detectors. Data taken by scanning a calibration source across multiple radial positions of a prototype dark matter detector demonstrated its functionality. Construction, heat load, and operation of the device are discussed, as is the effect of the motor on the detector operation. A sample dataset taken over multiple positions of a SuperCDMS detector is presented as an example of the utility of such a device.

Instrumentation and Detectors,High Energy Physics - Experiment

Superconducting Noncontact Device for Precision Positioning in Cryogenic Environments

Improving Resolution and Run Outs of a Superconducting Noncontact Device for Precision Positioning

Engineering and performance of a contactless linear slider based on superconducting magnetic levitation for precision positioning

Non-contact linear slider for cryogenic environment

A compact inertial nano-positioner operating at cryogenic temperatures

Dynamics of a Superconducting Linear Slider

Novel cryogenic motion control for aerospace

Cryogenic Test Stand for Characterization of Magnetocaloric Materials

Levitation Force of Small Clearance Superconductor–magnet System under Non-Coaxial Condition

Cryogenic optical beam steering for superconducting device calibration

Low temperature and high magnetic field performance of a commercial piezo-actuator probed $via$ laser interferometry

A simple method to measure the temperature and levitation height of devices rotating at cryogenic temperatures

Fabrication of Nbti Superconducting Joint by Electromagnetic Forming Method

Cryogen free spin polarized scanning tunneling microscopy and magnetic exchange force microscopy with extremely low noise

High-Q magnetic levitation and control of superconducting microspheres at millikelvin temperatures

A superconducting quantum interference device based read-out of a subattonewton force sensor operating at millikelvin temperatures

A New Magnetically Levitated Positioning Stage with Nanometer Resolution

Design And Detection Of Super-Precision Positioning Stage With Nanometer Resolution

A 1-2 K Cryogenic System with Light Weight, Long Life, Low Vibration, Low EMI and Flexible Cooling Capacity for the Superconducting Nanowire Single-Photon Detector

Cryogenic Goniometer for Measurements in Pulsed Magnetic Fields Fabricated Via Additive Manufacturing Technique

An In-Situ Movable Calibration Source for Cryogenic Particle Detectors