Abstract:With increasing applications of integrated circuits, the requirements for the quality of the corresponding substrate silicon wafers have become more stringent. Slicing is a key step in the manufacturing of silicon wafers. At present, free-abrasive multi-wire saw (MWS) technology is commonly employed for substrate silicon wafer processing. However, the actual temperature field in the cutting zone is unclear because of the narrow cutting zone in multi-wire sawing. Although a simulation method was adopted in this study, the distribution of the slurry in the cutting zone remains ambiguous, causing a large difference between the simulation results. The temperature field is an important cause of warpage, which significantly affects wafer quality. In this study, an experiment and simulation of the temperature field in the cutting zone of a MWS of monocrystalline silicon with free abrasives were performed. First, an experiment was designed to measure the temperatures at different positions in the cutting zone. Then, based on the experimental data of the fluid pressure distribution and the temperature field in the cutting zone, after obtaining the heat source model, a simulation analysis was conducted, and the results are consistent with the experimental results. Finally, based on the heat flux model, the temperature field distribution in the cutting zone under different cutting conditions was simulated and analyzed. Temperatures of 36.7, 39.4, 40.7, and 42.8 °C were obtained at 22.5, 62.5, 137.5, and 177.5 mm, respectively, from the slurry entrance in the cutting zone. According to the heat source model based on the pressure distribution data of slurry in the cutting zone, the temperature values obtained via simulation at 22.5, 62.5, 137.5, and 177.5 mm from the slurry inlet were 35.4, 37.4, 41.5, and 43.1 °C, respectively. The maximum temperature difference is 1.8K°C, and the average temperature difference is 0.2K°C. Thus, the validity of the heat source model was verified. Further, based on the heat source model, the maximum temperature for cutting a 300-mm monocrystalline silicon wafer was predicted as 48.4 °C. Moreover, the wire speed was found to greatly influence the maximum temperature in the cutting zone. Tension also affects the temperature of the cutting zone, but to a lesser extent than the wire speed.

Slicing process dynamic modelling of inner-diameter saw blade

Study on the Effect of Tool Inclination Angle in Machining Process Based on Three-Dimensional Thermo-Elastic-Plastic Model

A normal force model for ultrasonic vibration-assisted inner-diameter slicing of hard and brittle materials

Slicing parameter optimization based on wire net dynamic reliability constraint in multi-wire saw

Theoretical Analysis of Serrated Chip Formation Based on Ideal Models in High Speed Cutting

The effect of cut depth and distribution for abrasives on wafer surface morphology in diamond wire sawing of PV polycrystalline silicon

Influence of silicon anisotropy on surface shape deviation of wafer by diamond wire saw

Influence of diamond wire saw slicing parameters on (010) lattice plane beta-gallium oxide single crystal wafer

Sawing Force Prediction Model and Experimental Study on Vibration-Assisted Diamond Wire Sawing

Prediction and verification of wafer surface morphology in ultrasonic vibration assisted wire saw (UAWS) slicing single crystal silicon based on mixed material removal mode

Research on the analytical modeling of critical conditions of serrated Chip formation based on thermal-mechanical coupled material behavior

Molecular Dynamics Simulation on Cutting Mechanism in the Hybrid Machining Process of Single-Crystal Silicon

An ANSYS/LS-DYNA simulation and experimental study of circular saw blade cutting system of mulberry cutting machine

Investigation on bolt initial tensioning of inner-diameter saw blade

Study on the temperature field in the cutting zone for machining monocrystalline silicon wafer using free abrasive multi-wire saw

Multi-physics analytical modeling of the primary shear zone and milling force prediction

Preparation and characterization of ultra-thin dicing blades with different bonding properties

Experimental study regarding the surface roughness of circular crystal wafers sliced by a multi-wire saw with reciprocating and rocking functions

Experiment and theoretical prediction for surface roughness of PV polycrystalline silicon wafer in electroplated diamond wire sawing

The Mechanical Analysis of the Composite Reinforced Circular Saw Blade

Analytical modelling of side grinding of orthogonal laminated SiCf/SiC composites based on effective elastic properties