Safety Planning for Military (SAFE MIL): rationale, design, and safety considerations of a randomized controlled trial to reduce suicide risk among psychiatric inpatients.

Marjan Ghahramanlou-Holloway,Gregory K Brown,G. Currier,L. Brenner,K. Knox,Geoffrey G. Grammer,Jaime T. Carreno-Ponce,Barbara Stanley

DOI: https://doi.org/10.1016/j.cct.2014.07.003

IF: 2.261

2014-09-01

Contemporary Clinical Trials

Abstract:

What problem does this paper attempt to address?

Adsorption Properties of Coating Modified Nano CaO-Based CO2 Adsorbents

Xiaochong Xue,Yan Wang,Sufang Wu

2015-01-01

Abstract:The adsorbent was prepared in a spray granulation method by mixing the inert material MgO or TiO2 coating modified with nano-CaCO3 and with alumina sol as binder. The thermo-gravimetric analyzer was used to investigate the decomposition temperature, adsorption rate, adsorption capacity and stability under the conditions of reactive carbonation temperature 600℃, CO2partial pressure 0.015 MPa,and calcination temperature 750℃ in nitrogen gas. The results showed that the decomposition temperature of MgO, TiO2 coating modified nano CaO-based CO2adsorbent was increased by 20 and 35℃, respectively. The adsorption rate and adsorption capacity were both higher than those of uncoated nano CaO-based CO2 adsorbent after 30 carbonation-calcination cycles. The TiO2 coated nano CaO-based CO2adsorbent had the highest stability with 34.85% decrement after 30 cycles, and the MgO coated one was 38.89% while the uncoated nano CaO-based CO2 adsorbent was 54.87%.
Performance of Nano-Caco3 Coated with SiO2 on CO2 Adsorption at High Temperature

WU Rong,WU Sufang

DOI: https://doi.org/10.3321/j.issn:0438-1157.2006.07.041

2006-01-01

Abstract:Nano-CaCO_3 particles were surface-coated with SiO_2 by the sol-gel method and used as the high temperature CO_2 adsorption material.CaCO_3 samples prepared at 60—90℃ were characterized with TEM, EDS and XRD methods and the initial and final decomposition temperature were determined with TGA.The CO_2 adsorption ratio and carbonation-calcination characteristics were evaluated in a 12 mm fixed bed reactor.The analytical results showed that there was an amorphous SiO_2 film formed on the surface of nano-CaCO_3,and the atomic ratio of Si to Ca is 1∶39.The initial and final decomposition temperatures were 595—620℃ and 800—820℃ respectively.The maximum CO_2 adsorption ratio of SiO_2 coated with nano-CaCO_3 was 92.1% at 600℃with a 10% increase as compared with the uncoated nano-CaCO_3 particles.After 20 cyclic carbonation and calcination runs, CO_2 adsorption ratio of the SiO_2 coated samples was 63%.The XRD analysis illustrated that the crystal type of nano-CaCO_3 had no change after 20 cyclic runs.
Adsorption of Nitrous Oxide on Activated Carbons

Yong Peng,Fumin Zhang,Chunhui Xu,Qiang Xiao,Yijun Zhong,Weidong Zhu

DOI: https://doi.org/10.1021/je9001625

2009-01-01

Abstract:The adsorption equilibria of nitrous oxide (N2O) on three commercial activated carbons were systematically investigated by means of a volumetric method at pressures up to 101 kPa and temperatures ranging from (195 to 323) K. The multiple-process adsorption equilibrium model appropriately describes the equilibrium data over the whole range of the applied conditions. The estimated total adsorption capacity of N2O is higher for activated carbon which possesses a higher pore volume determined by N-2 adsorption at 77 K. The thermodynamic properties such as the adsorption equilibrium constant and enthalpy associated with adsorption were derived to characterize interactions between adsorbate and adsorbent.
Effect of Nitric Acid Pretreatment on the Properties of Activated Carbon and Supported Palladium Catalysts

Jiayun Li,Lei Ma,Xiaonian Li,Chunshan Lu,Huazhang Liu

DOI: https://doi.org/10.1021/ie0488896

2005-01-01

Industrial & Engineering Chemistry Research

Abstract:The activated carbon was pretreated with different concentrations of HNO3 (from 0.5 to 67%). The amount and type of oxygen-containing groups on the activated carbon were determined with the adsorption neutralization method and temperature-programmed desorption (TPD) of CO and CO2; furthermore, the density of total acidity (DTA) has been proposed. The Pd particle size of Pd/C catalysts was measured by X-ray diffraction patterns (XRD), CO chemisorption, and TEM. The experimental results indicated that the amount of oxygen-containing groups and the total acidity on the activated carbons, the Pd particle size and catalytic activity of Pd/C catalysts are highly dependent upon the HNO3 concentration used in the pretreatment. The pretreatment of activated carbon with a low concentration of HNO3 can increase the structure parameters due to removal of the impurities, will be beneficial to create an appropriate DTA environment, and will further improve the Pd dispersion and the catalytic activity of Pd/C catalysts. The highest catalytic activity and the finest Pd particle of Pd/C catalysts can be reached at 2.5% concentration of HNO3. A too-large amount of oxygen-containing groups assembling densely on the activated carbon will influence the Pd dispersion on the activated carbon well.
Behavior of CaTiO3/Nano-CaO As a CO2 Reactive Adsorbent

S. F. Wu,Y. Q. Zhu

DOI: https://doi.org/10.1021/ie900900r

2010-01-01

Industrial & Engineering Chemistry Research

Abstract:This study focuses on the preparation of a CaTiO3-coated nano-CaO-based CO2 adsorbent (CaTiO3/nano-CaO) for the improvement of sorption properties. The CaTiO3-coated nano-CaO adsorbent was prepared by forming Ti(OH)4 from the hydrolysis of titanium alkoxide in a nano-CaCO3 suspended solution. The resulting Ti(OH)4-coated nano-CaCO3 was then heated and calcined. Test results from transmission electron microscopy and scanning electron microscopy with energy dispersive X-ray spectroscopy show that an obvious film of TiO2 was formed on the surface of nano-CaCO3 after heating. X-ray diffraction analysis also showed that the nano-CaTiO3 layer was formed at 750 °C, a calcination temperature that causes the reaction of TiO2 with nano-CaO. The cyclic tests of reactive sorption capacity were conducted in a thermogravimetric analyzer under the following conditions: 0.02 MPa CO2 partial pressure, carbonation temperature of 600 °C, and calcination temperature of 750 °C. Test results showed that CaTiO3 coated onto the ...
Enhancement of CO2 Adsorption on High Surface Area Activated Carbon Modified by N2, H2 and Ammonia

Zhijuan Zhang,Mingyao Xu,Haihui Wang,Zhong Li

DOI: https://doi.org/10.1016/j.cej.2010.03.070

IF: 15.1

2010-01-01

Chemical Engineering Journal

Abstract:The activated carbons (ACs) with high surface area were modified separately by using ammonia aqueous solution impregnation and microwave irradiation in an atmosphere of N2 or H2 in order to improve their adsorption properties toward CO2. The modified ACs were characterized, and the surface chemical properties of the ACs were determined separately by FTIR, Boehm titration and X-ray photoelectron spectroscopy (XPS) methods. The isotherms of CO2 on the modified ACs were measured. Results showed that after surface modification, the contents of elements C and N of the samples increased, while that of the element O of the samples decreased in comparison with the original AC. Correspondingly, the amounts of the surface basic groups of the modified ACs increased, while those of the surface acidic groups decreased as compared to the original AC. The use of microwave irradiation in an atmosphere of N2 to modify the carbon can make the total basic groups of the surfaces of the ACs be the highest among the modified ACs. As a consequence of that, the modified AC samples had higher adsorption capacities of CO2 than the original AC, and the more the surface basic groups of the ACs, the higher the adsorption capacity of the ACs for CO2. The amount adsorbed of CO2 on the modified AC by the microwave irradiation in the atmosphere of N2 was up to 3.75mmol/g at 1atm and 293K, having an increase of 28% in comparison with the original AC.
Adsorption of Nitrogen Dioxide on Nitrogen-Enriched Activated Carbons

Aleksandra Bazan-Wozniak,Agnieszka Nosal-Wiercińska,Judyta Cielecka-Piontek,Selehattin Yilmaz,Robert Pietrzak

DOI: https://doi.org/10.3390/ijms25084421

IF: 5.6

2024-04-18

International Journal of Molecular Sciences

Abstract:The aim of this study was to obtain nitrogen-enriched activated carbons from orthocoking coal. The initial material was subjected to a demineralisation process. The demineralised precursor was pyrolysed at 500 °C and then activated with sodium hydroxide at 800 °C. Activated carbon adsorbents were subjected to the process of ammoxidation using a mixture of ammonia and air at two different temperature variants (300 and 350 °C). Nitrogen introduction was carried out on stages of demineralised precursor, pyrolysis product, and oxidising activator. The elemental composition, acid-base properties, and textural parameters of the obtained carbon adsorbents were determined. The activated carbons were investigated for their ability to remove nitrogen dioxide. The results demonstrated that the ammoxidation process incorporates new nitrogen-based functional groups into the activated carbon structure. Simultaneously, the ammoxidation process modified the acid-base characteristics of the surface and negatively affected the textural parameters of the resulting adsorbents. Furthermore, the study showed that all of the obtained carbon adsorbents exhibited a distinct microporous texture. Adsorption tests were carried out against NO2 and showed that the carbon adsorbents obtained were highly effective in removing this gaseous pollutant. The best sorption capacity towards NO2 was 23.5 mg/g under dry conditions and 75.0 mg/g under wet conditions.

biochemistry & molecular biology,chemistry, multidisciplinary
Performance of CO2 Adsorption on Modified Activated Carbons Derived from Okara Powder Waste: Impacts of Ammonia Impregnation

Tuan-Dung Hoang,Yan Liu,Minh Thang Le

DOI: https://doi.org/10.3390/pr12092024

IF: 3.5

2024-09-21

Processes

Abstract:The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties. The impregnated ACs were characterized, where the chemical composition and properties of the ACs were analyzed by SEM-EDX and FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24, 48, and 72 h. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C=O stretch and N-H groups. CO2 uptakes of activated carbons are 0.24; 1.78; 2.24; and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in the literature.

engineering, chemical
Carbon Dioxide Adsorption by a High-Surface-Area Activated Charcoal

Ahmed S. Ahmed,Mohammed Alsultan,Assim A. Sabah,Gerhard F. Swiegers

DOI: https://doi.org/10.3390/jcs7050179

2023-05-01

Journal of Composites Science

Abstract:An activated carbon (AC) with a high surface area of 4320.7 m2/g was synthesized via the chemical and thermal processing of walnut residues. The resulting activated charcoal was characterized by various techniques, including Brunauer–Emmett–Teller (BET) surface area analysis, scanning electron microscopy (SEM), and IR spectroscopy. The prepared activated carbon was studied for its capacity to adsorb CO2 gas. When exposed to CO2 for 60 min in a closed chamber at atmospheric pressure at 25 °C, the adsorption of a notable 301.1 mmol CO2 (13.25 g CO2) per gram of activated carbon was observed.
Nitrogen Doping of Activated Carbon Loading Fe2O3 and Activity in Carbon-Nitric Oxide Reaction

Wan Xian-kai,Zou Xue-quan,Shi Hui-xiang,Wang Da-hui

DOI: https://doi.org/10.1631/jzus.2007.a0707

2007-01-01

Journal of Zhejiang University SCIENCE A

Abstract:Nitrogen doping of activated carbon loading Fe 2 O 3 was performed by annealing in ammonia, and the activity of the modified carbon for NO reduction was studied in the presence of oxygen. Results show that Fe 2 O 3 enhances the amount of surface oxygen complexes and facilitates nitrogen incorporation in the carbon, especially in the form of pyridinic nitrogen. The modified carbon shows excellent activity for NO reduction in the low temperature regime (<500 °C) because of the cooperative effect of Fe 2 O 3 and the surface nitrogen species.
Freundlich, Langmuir, Temkin, DR and Harkins-Jura Isotherm Studies on the Adsorption of CO2 on Various Porous Adsorbents

Fatma Oguz Erdogan

DOI: https://doi.org/10.1515/ijcre-2018-0134

IF: 1.636

2018-12-15

International Journal of Chemical Reactor Engineering

Abstract:Abstract The objective of the study was to prepare low-cost activated carbon from cornelian cherry stones (Cornus mas L.) and compare its adsorption capacities for CO 2 with that of commercial multiwalled carbon nanotubes, activated carbon, MCM-41 and four zeolites (silver exchanged, 13X, faujasite type and linde type A). BET, t-plot and DFT methods were used for the characterization of all adsorbent samples based on N 2 adsorption-desorption data obtained at 77 K. The produced activated carbon samples (KAC and NAC) were also characterized by scanning electron microscopy (SEM). The adsorption data were evaluated by several isotherm models such as Freundlich, Langmuir, Temkin, DR and Harkins-Jura isotherm models. Langmuir adsorption isotherms constants related to adsorption capacity, W m were found as 11.496, 6.175, 4.189, 3.986 and 3.50 mmol/g for NAC, KAC, faujasite type zeolit, MCM-41 and AC, respectively. The CO 2 adsorption capacities of the silver exchanged, 13X, faujasite type and linde type A zeolites were 10.814, 10.241, 14.608 and 13.343 wt%, respectively. Microporous zeolites showed higher CO 2 adsorption capacities than the mesoporous MCM-41 and MWCNT. The CO 2 adsorption capacity of commercial activated carbon (AC) was found to be 9.428 wt%, while the CO 2 adsorption capacities of activated carbons obtained using NaOH and KOH were found to be 13.685 and 15.057 wt%, respectively. The highest CO 2 adsorption capacity of 15.057 wt% was achieved with KAC. It could be confirmed that NaOH or KOH activation plays an important role to determine the porous structure and amount of CO 2 adsorbed. Results showed that activated carbon produced from cornelian cherry stones is suitable for the adsorption of CO 2 and could be used as a low cost effective adsorbent in the capture of CO 2 .

engineering, chemical
Adsorption of low-concentration carbon dioxide on amine-modified carbon nanotubes at ambient temperature

Qing Ye,Jianqing Jiang,Chunxia Wang,YaMin Liu,Hua Pan,Yao Shi

DOI: https://doi.org/10.1021/ef201699w

IF: 4.6541

2012-01-01

Energy & Fuels

Abstract:A solid amine adsorbent for CO2 was developed by carbon nanotubes (CNTs) impregnated with tetraethylenepentamine (TEPA). The adsorption behavior toward CO2 (2.0 vol %) was investigated in a fixed-bed column. After modification, the adsorption capacity of CNTs-TEPA reached 2.97 mmol g(-1) at 298 K Rising temperatures from 283 to 313 K enhanced the CO2 adsorption capacity. The maximum adsorption capacity was approximately 3.56 mmol g(-1) at 313 K. The adsorption capacity was also influenced by moisture and reached as high as 3.87 mmol g(-1) (2.0% H2O). In comparison to many other types of modified carbon or silica adsorbents in the literature, CNTs-TEPA had a higher adsorption capacity at the same temperature. The adsorption capacity for CO2 remained almost the same after cyclic regeneration experiments. A deactivation model, capable of describing the uptake of CO2, was applied under various conditions. In all cases, the experimental data agreed with the predicted breakthrough model.
Adsorption Of Volatile Organic Compounds In Nitrogen Streams On Oxidized Activated Carbon Fibres

Fy Kang,Zh Huang,Km Liang,Jb Yang,H Wu

DOI: https://doi.org/10.1260/0263617011494286

2001-01-01

Adsorption Science & Technology

Abstract:Viscose rayon-based activated carbon fibres (ACFs) with low and high specific surface areas were treated with conc. HNO3, 30 wt% H2O2 and air at different temperatures. The pore textures and surface chemistries of the samples were characterized by nitrogen adsorption at 77 K and X-ray photoelectron spectroscopic (XPS) methods. The adsorption of traces of volatile organic compounds (VOCs), i.e. benzene and methyl ethyl ketone (MEK), in nitrogen streams on the samples wwa measured by a gravimetric method. The results showed that the surface oxygen complexes and pore textures of all the oxidized ACFs were modified and differed depending on whether oxidation had been conducted under gaseous or solution conditions. ACFs with different specific surface areas possessed different adsorption characteristics towards VOC vapours after subjection to oxidation treatment.
The effect of humidity on the enhanced CO2 adsorption of amine-functionalized microporous activated carbon

Masoumeh Lotfinezhad,Maryam Tahmasebpoor,Covadonga Pevida

DOI: https://doi.org/10.1007/s11356-024-35559-x

IF: 5.8

2024-11-22

Environmental Science and Pollution Research

Abstract:Cost-effective and environmentally friendly sorbents were created for capturing CO 2 by incorporating monoethanolamine (MEA) and tetraethylenepentamine (TEPA) onto a microporous activated carbon (AC) material. The application of a KOH reagent enhanced the surface area and pore volume of the carbon material. The BET, SEM, EDX, and FTIR techniques were employed to analyze the structural and surface properties of the developed samples. Raw AC possessed the highest surface area and largest micropore volume equal to 786 m 2 /g and 0.33 cm 3 /g, respectively. The amine impregnation increased the nitrogen content of the carbon material, but it also significantly reduced the BET surface area and total pore volume, which are primarily responsible for physically adsorbing CO 2 towards ACs. The CO 2 adsorption performance of the raw and impregnated ACs was experimentally evaluated using thermogravimetric analysis (TGA) at different adsorption temperatures (25 and 50 °C) and CO 2 concentrations (10 and 90 vol.%). The findings demonstrated that the raw AC exhibited the highest capacity for CO 2 adsorption. Specifically, at a temperature of 25 °C and pressure of 1 bar (10 vol.% CO 2 , N 2 balance), the raw AC achieved an uptake of 1.2 mmol/g, which was 60.3% and 79.3% higher compared to the CO 2 uptake of MEA-AC (0.5 mmol/g) and TEPA-AC (0.3 mmol/g), respectively. It is surprising that the combined uptake of CO 2 + H 2 O increased by 12.5 and 23.4 wt.% (equivalent to 7 and 13 mmol/g) for MEA-AC and TEPA-AC, respectively, when humid flue gas was taken into account under the conditions of 50 °C, with 10 vol.% CO 2 , 4 vol.% H 2 O, and N 2 balance. These results indicate that the presence of H 2 O facilitates the chemisorption of CO 2 by the novel and highly promising carbon-based sorbent prepared in this study, leading to an increased capacity for adsorbing CO 2 under water vapor containing flue gases.

environmental sciences
CO2adsorption on Crab Shell Derived Activated Carbons: Contribution of Micropores and Nitrogen-Containing Groups

Tao Chen,Shubo Deng,Bin Wang,Jun Huang,Yujue Wang,Gang Yu

DOI: https://doi.org/10.1039/c5ra04937g

IF: 4.036

2015-01-01

RSC Advances

Abstract:Nitrogen-doped activated carbons with high and selective CO2 adsorption are attractive for carbon capture, but the contribution of nitrogen-containing groups to CO2 adsorption has not been clearly elucidated. In this study, crab shells are used as a carbon precursor for the preparation of effective N-containing activated carbons for CO2 adsorption. The activated carbon prepared at a KOH/C mass ratio of 1.5 and activation temperature of 650 degrees C has the highest CO2 adsorption of 1.57 mmol g(-1) at 0.15 bar & 25 degrees C and 4.37 mmol g(-1) at 1 bar & 25 degrees C. The activated carbon also exhibits better adsorption selectivity for CO2 than conventional activated carbons, and the content of pyrrolic-N in the activated carbons shows a positive relationship with CO2/N-2 selectivity. The activated carbons prepared under different activation conditions contain 5.1-8.5% nitrogen in the form of pyridinic-N, pyrrolic-N, quaternary nitrogen, and pyridinic-N-oxide, accounting for at least 0.9-78.2% contribution to CO2 adsorption at 25 degrees C & 1 bar. About 45.1-47.3% of doped nitrogen is verified to be pyrrolic-N via X-ray photoelectron spectroscopy (XPS) analysis, which is effective for CO2 adsorption. However, the effective micropores are mainly responsible for CO2 adsorption on the well-developed activated carbons via a micropore filling mechanism.
Tailoring tea residue-derived nitrogen-doped activated carbon for CO2 adsorption: influence of activation temperature and activating agents

Amirul Hafiiz Ruhaimi,Muhammad Arif Ab Aziz

DOI: https://doi.org/10.1007/s11356-024-35154-0

IF: 5.8

2024-10-10

Environmental Science and Pollution Research

Abstract:Embracing CO 2 mitigation strategies, such as state-of-the-art CO 2 capture technologies, is essential for effectively reducing atmospheric carbon levels and advancing global efforts toward a more sustainable future. In this context, adsorption sequestering techniques utilising carbon materials have emerged as promising candidates for CO 2 capture. These materials have been extensively researched with a range of tuning methods to optimise their physicochemical features. In this study, an alteration of the N-doped activated carbon was successfully performed, utilizing tea residue as the carbon precursor and ammonia as the nitrogen source, facilitated through an impregnation procedure. With the objective of discovering the effect of diverse activation parameters on prepared adsorbent physicochemical properties, several selections of activating agents (AA) were investigated: KOH, H 3 PO 4 , ZnCl 2, and NaOH, together with broad thermal activation temperature from 873 to 1173 K. The best-performed adsorbents from the respective AC group were subjected to several characterisation analyses and found to the enhanced structural features, heteroatom doped-rich surface (i.e. N and O); together with AA-induced metal/mineral functionalization, the NaOH-used AC (NAC-N-1173) was the optimum-performed adsorbent with a promising 4.12 mmol/g CO 2 uptake capacity, higher than other prepared adsorbent including N-doped tea residue-derived char and commercialized AC with 175 and 325% higher, respectively.

environmental sciences
Effect of Nitrogen Doping on the Reduction of Nitric Oxide with Activated Carbon in the Presence of Oxygen

Xian-kai Wan,Hui-xiang Shi,Xue-quan Zou,Peng Ge,Da-hui Wang

DOI: https://doi.org/10.1631/jzus.a073019

2008-01-01

Abstract:Nitrogen doping of activated carbon (AC) was performed by annealing both in ammonia and nitric oxide, and the activities of the modified carbons for NO reduction were studied in the presence of oxygen. Results show that nitrogen atoms were incorporated into the carbons, mostly in the form of pyridinic nitrogen or pyridonic nitrogen. The effect of nitrogen doping on the activities of the carbons can be ignored when oxygen is absent, but the doped carbons show desirable activities in the low temperature regime (≤500 °C) when oxygen is present. The role of the surface nitrogen species is suggested to promote the formation of NO 2 in the presence of oxygen, and NO 2 can facilitate decomposition of the surface oxygen species in the low temperature regime.
Nitrogen configuration enriched N-doped activated carbon from spent tea leaves through an ammonia impregnation approach for CO 2 adsorption

Amirul Hafiiz Ruhaimi,Muhammad Arif Ab Aziz

DOI: https://doi.org/10.1039/d4nj03301a

IF: 3.3

2024-09-04

New Journal of Chemistry

Abstract:An N configuration enriched N-doped activated carbon adsorbent was successfully synthesised using an ammonia-induced N impregnation step with spent tea leaves (STLs) as a carbon precursor. In this study, activated carbon (AC) has been synthesized using a two-step H 3 PO 4 activation method. SEM, Raman spectroscopy, N 2 physisorption, ultimate elemental analysis, and XPS were employed to characterise the physicochemical features of the prepared adsorbent. According to the characterisation analysis, the characteristics of the prepared adsorbent solely (either high in the surface area or N-content) are not sufficient enough to achieve good uptake capacity, and this has been demonstrated using the un-doped AC (AC) and commercialised AC (CAC) with a high surface area and N-doped biochar (NC) with a high N content. Through a volumetric adsorption step, it was revealed that the N-doped AC (NA773C) exhibited an improved CO 2 adsorption uptake capacity of 2.66 mmol g −1 , which is about 78%, 400%, and 177% higher than those of NC, AC and CAC, respectively, at 298 K and under atmospheric pressure conditions. With the results obtained from the characterisation analysis, it was found that a high surface area, along with a high N–C composition possessed by NA773C compared to those of other adsorbents endowed it with a high CO 2 uptake capacity.

chemistry, multidisciplinary
Adsorption of Carbon Dioxide on Activated Carbon

Bo Guo,Liping Chang,Kechang Xie

DOI: https://doi.org/10.1016/s1003-9953(06)60030-3

2006-01-01

Abstract:The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Freundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.
The effect of the active carbonyl groups and residual acid on the ammonia adsorption over the acid-modified activated carbon

Changming Li,Shuying Zhao,Ming Li,Zhiliang Yao,Yang Li,Chuanqiang Zhu,Si-Min Xu,Junjie Li,Jian Yu

DOI: https://doi.org/10.3389/fenvs.2023.976113

IF: 5.411

2023-01-17

Frontiers in Environmental Science

Abstract:The deep insight into the adsorption mechanism of ammonia (NH3) over acid-modified activated carbon will be of great significance to develop more efficient carbon materials for NH3 adsorption. In this work, a co-adsorption mechanism of NH3 and residual nitric acid (HNO3) on the active carboxyl site is proposed to elaborate the enhanced NH3 adsorption capacity over the acid-modified activated carbon based on both the experimental and density functional theory (DFT) results. The adsorption behaviors of NH3 over the different acid-modified activated carbon samples show that the activated carbon modified by 10 M HNO3 at 90 oC possesses the best NH3 adsorption capacity (40 mg/g), and the residual HNO3 can be observed with the release of both NOx and NH3 during the heat treatment of the used HNO3-modified activated carbon. The multiple structural characterizations reveal that the activated carbon can be oxidized and etched by HNO3 with enriched pore structure and oxygen-containing functional groups, and acidic functional groups play a key role in the improved NH3 adsorption capacity. DFT calculations further display that the carboxyl functional group can strongly interplay with NH3 or HNO3 with the lowest adsorption energy (-0.66 eV and -0.79 eV, respectively), and the co-adsorption of NH3 and HNO3 around the carboxyl functional group forms a strong circular hydrogen-bond network among NO3−, NH4+ and carbonyl and further decreases the adsorption energy (-1.63 eV). The experimental and theoretical results together demonstrate that the oxidation and etching of activated carbon by acid enrich the active surface carboxyl functional groups, and the co-adsorption of NH3 with the residual HNO3 around the carboxyl functional group through the strong circular hydrogen-bond network accounts for the enhanced NH3 adsorption capacity of the acid-modified activated carbon.

environmental sciences

Safety Planning for Military (SAFE MIL): rationale, design, and safety considerations of a randomized controlled trial to reduce suicide risk among psychiatric inpatients.

Adsorption Properties of Coating Modified Nano CaO-Based CO2 Adsorbents

Performance of Nano-Caco3 Coated with SiO2 on CO2 Adsorption at High Temperature

Adsorption of Nitrous Oxide on Activated Carbons

Effect of Nitric Acid Pretreatment on the Properties of Activated Carbon and Supported Palladium Catalysts

Behavior of CaTiO3/Nano-CaO As a CO2 Reactive Adsorbent

Enhancement of CO2 Adsorption on High Surface Area Activated Carbon Modified by N2, H2 and Ammonia

Adsorption of Nitrogen Dioxide on Nitrogen-Enriched Activated Carbons

Performance of CO2 Adsorption on Modified Activated Carbons Derived from Okara Powder Waste: Impacts of Ammonia Impregnation

Carbon Dioxide Adsorption by a High-Surface-Area Activated Charcoal

Nitrogen Doping of Activated Carbon Loading Fe2O3 and Activity in Carbon-Nitric Oxide Reaction

Freundlich, Langmuir, Temkin, DR and Harkins-Jura Isotherm Studies on the Adsorption of CO2 on Various Porous Adsorbents

Adsorption of low-concentration carbon dioxide on amine-modified carbon nanotubes at ambient temperature

Adsorption Of Volatile Organic Compounds In Nitrogen Streams On Oxidized Activated Carbon Fibres

The effect of humidity on the enhanced CO2 adsorption of amine-functionalized microporous activated carbon

CO2adsorption on Crab Shell Derived Activated Carbons: Contribution of Micropores and Nitrogen-Containing Groups

Tailoring tea residue-derived nitrogen-doped activated carbon for CO2 adsorption: influence of activation temperature and activating agents

Effect of Nitrogen Doping on the Reduction of Nitric Oxide with Activated Carbon in the Presence of Oxygen

Nitrogen configuration enriched N-doped activated carbon from spent tea leaves through an ammonia impregnation approach for CO 2 adsorption

Adsorption of Carbon Dioxide on Activated Carbon

The effect of the active carbonyl groups and residual acid on the ammonia adsorption over the acid-modified activated carbon