Abstract:Properties such as wide bandgap, higher electromechanical coupling, and low dielectric permittivity have propelled ScxAl1−xN as an advantageous material for optoelectronics and RF applications. ScxAl1−xN devices are challenging to fabricate because ScAlN films are complex to etch, especially with greater scandium concentrations. Our group has developed a procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. The etching rate of Sc0.125Al0.875N$${\mathrm{Sc}}_{0.125}{\mathrm{Al}}_{0.875}\mathrm{N}$$, Sc0.20Al0.80N$${\mathrm{Sc}}_{0.20}{\mathrm{Al}}_{0.80}\mathrm{N}$$, and Sc0.40Al0.60N$${\mathrm{Sc}}_{0.40}{\mathrm{Al}}_{0.60}\mathrm{N}$$ was found to be approximately, 365 nm/min, 243 nm/min, and 81 nm/min, respectively. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma etch, high-temperature annealing, and wet etching without affecting the sidewall verticality. Preliminary results of ongoing device fabrication that use this developed etch approach are also presented herewith to give an overview of the ongoing work.Graphical abstractOur group has developed a state-of-the-art procedure to etch ScxAl1−xN (x = 0.125, 0.20, 0.40) thin films (~ 730 nm thick), which results in vertical sidewalls that approach 85–90° (± 0.4°) and reduce the degree of the undercut. To maintain uniformity between various Sc compositions during the etching process, a nitrogen atmosphere was employed for high-temperature annealing, followed by immersion in a bath of tetramethyl ammonium hydroxide (TMAH) for wet etching. A 25% concentrated TMAH solution was used at 78–82 °C to etch down the ScxAl1−xN film layer. Experimental results demonstrated that an identical etching profile can be obtained by TMAH vapor as well. We demonstrated how the annealing process recovers the deterioration introduced into the ScxAl1−xN by the ion-bombardment effect developed during the SiO2/SiNx hard mask dry etch step, ultimately preventing lateral etching. We have also reduced sidewall roughness of a post-etched ScxAl1−xN film with the combination of inductively coupled plasma (ICP) etch, high-temperature annealing, and wet etching without affecting the sidewall verticality.

Al$_3$Sc thin films for advanced interconnect applications

Effects of Sc on the Vacancy and Solute Behaviours in Aluminium

Cu$_x$Al$_{1-x}$ films as Alternatives to Copper for Advanced Interconnect Metallization

Increased thermal conductivity and decreased electron–phonon coupling factor of the aluminum scandium intermetallic phase (Al3Sc) compared to solid solutions

Multiscale Characterization of the Nucleation and 3D Structure of Al3Sc Phases Using Electron Microscopy and Synchrotron X-ray Tomography

Deposition of highly crystalline AlScN thin films using synchronized high-power impulse magnetron sputtering: From combinatorial screening to piezoelectric devices

Aluminum-Scandium: A Material for Semiconductor Packaging

Nanoscale Structural and Chemical Properties of Ferroelectric Aluminum Scandium Nitride Thin Films

Atomic Layer Deposition Of Sc2o3 For Passivating Algan/Gan High Electron Mobility Transistor Devices

Cast Microstructure and Crystallographic Features of Al3Sc Dendrites in High Sc-Contained Al-Sc Alloys

Etching of scandium-doped aluminum nitride using inductively coupled plasma dry etch and tetramethyl ammonium hydroxide

Atomic Layer Deposition of ScF 3 and Sc x Al y F z Thin Films

Al1−xScxN Thin Films at High Temperatures: Sc-Dependent Instability and Anomalous Thermal Expansion

Alscn Thin Film Based Surface Acoustic Wave Devices with Enhanced Microfluidic Performance

Effect of Sc spatial distribution on the electronic and ferroelectric properties of AlScN

Understanding Interfaces in AlScN/GaN Heterostructures

Fabrication of Ultrathin Ferroelectric Al0.7Sc0.3N Films under Complementary‐Metal‐Oxide‐Semiconductor Compatible Conditions by using HfN0.4 Electrode

Deposition of highly-crystalline AlScN thin films using synchronized HiPIMS -- from combinatorial screening to piezoelectric devices

Epitaxial Growth of Sc0.09Al0.91N and Sc0.18Al0.82N Thin Films on Sapphire Substrates by Magnetron Sputtering for Surface Acoustic Waves Applications

Long-term stability and oxidation of ferroelectric AlScN devices: An operando HAXPES study

Discontinuous Precipitation of Nano-Al3Sc Particles in Al-Sc Alloy and Its Effect on Mechanical Property