Abstract:Methods and results of the experimental and numerical investigation of the 1D heat transfer properties of a multifunctional syntactic foam. Top: experimental setup with schematic representation of the position of the thermocouples and boundary conditions; bottom left: microstructure of a representative sample of epoxy/hollow glass microspheres (HGM)/phase change material (PCM) syntactic foam; bottom right: temperature as a function of time in the heating experiment for the thermocouple located at 13 mm from the hot surface for different foam compositions. Data from the experiments (dotted line) and from the numerical modeling (solid line). Syntactic foams are lightweight porous composites obtained by the addition of hollow glass microspheres (HGMs) to a polymer matrix. This work experimentally and numerically investigates the thermal behavior of epoxy‐based syntactic foams with enhanced multifunctionality produced by incorporating microencapsulated phase change materials (PCMs) as functional fillers, providing thermal energy storage and temperature stabilization due to its large latent heat of melting. Foams are fabricated using varying ratios of HGMs (0–40 vol%) and PCM (0–40 vol%) to achieve tuned densities and thermal properties with a total filler content of up to 40 vol%. A one‐dimensional numerical heat transfer model based on the enthalpy method is presented to simulate the thermal behavior of these materials. The model accurately incorporates the specific heat and thermal conductivity of the foam components, as well as the latent heat absorption during PCM melting (up to 68 J/g). The model is experimentally validated by demonstrating good agreement with the measurements of transient temperature profiles during heating tests on the foam samples. The validated tool is then leveraged to model the thermal response of the foams under a sinusoidally varying heat source, similar to the possible real applicative scenarios. These results can help optimize foam compositions balancing energy storage density, heat transfer properties, and structural support for lightweight energy storage systems. Potential applications include high‐efficiency thermal management in battery packs, electronic cooling, solar energy storage, and sustainable temperature‐controlled buildings. Highlights Foams with 0–40 vol% PCM and 0–40 vol% HGM show up to 68 J/g latent heat. 1D numerical model accurately captures thermal conductivity and PCM phase change. Validated model simulates thermal response under sinusoidal heat, optimizing foam composition. Foams act as thermal reservoirs, maintaining up to 5°C lower surface temperatures than epoxy.

Thermal and mechanical properties of AlSi7Mg matrix syntactic foams reinforced by Al$_2$O$_3$ or SiC particles in matrix

Thermal and mechanical properties of AlSi7Mg matrix syntactic foams reinforced by Al 2 O 3 or SiC particles in matrix

Interface characterization and mechanical property of an aluminum matrix syntactic foam with multi-shelled hollow sphere structure

Enhancement in the Mechanical Properties of Newly Developed Ceramic Reinforced Al-Based Syntactic Foams: Analysis of Microstructure, Mechanical Response, and Energy Absorption Properties

Modeling the thermal behavior of multifunctional syntactic foams containing phase change materials for heat management applications

Challenges in the thermal modeling of highly porous carbon foams

Numerical and experimental characterization of high-temperature heat transfer in a ceramic foam with dual-scale porosity

Experimental Characterization of Al2O3 Foam Based on High Temperature Thermal Response Experiments

Investigations of Thermal Conductivity and Radiation Properties of Al2o3 Foam Materials Based on High Temperature Thermal Response Experiments

Thermal properties of a high volume fraction SiC particle-reinforced pure aluminum composite

Acoustic-pressure-assisted engineering of aluminium foams

Effect of Heat Treatment on the Microstructure, Compressive Property, and Energy Absorption Response of the Al–Mg–Si Alloy Foams

Thermo-mechanical characterization of carbon-based ceramic foams for high temperature space application

Microstructure and Strength Correlation of Pure Al and Al-Mg Syntactic Foam Composites Subject to Uniaxial Compression

High temperature and mesostructure effect on aluminum foam compression responses

Mg-matrix syntactic foam filled with alumina hollow spheres coated by MgO synthesized with solution coating-sintering

Effects of particle size, bimodality and heat treatment on mechanical properties of pumice reinforced aluminum syntactic foams produced by cold chamber die casting

Study of Micro-Structure Based Effective Thermal Conductivity of Graphite Foam

Preparation and Compressive Performance of an A356 Matrix Syntactic Foam

Characterization and modeling of the temperature-dependent thermal conductivity in sintered porous silicon-aluminum nanomaterials

Experiment research on the dynamic mechanical behavior of aluminum matrix syntactic foam