Abstract:The DPF regeneration is crucial for reducing backpressure, minimizing negative impacts on engine power and fuel economy, but the changes in particulate emission characteristics it brings are worth studying. In this study, the influence of DPFs with different soot loadings on exhaust back pressure and particle emission characteristics, as well as the particle number emission, particle size distribution, and thermal field distribution characteristics during regeneration was investigated based on engine bench test. Results reveal that the exhaust back pressure increases linearly with the engine speed, as well as the soot loading. The increase of DPF soot loading leads to a considerable increase in the reduction efficiency of particle number (PN) and particulate matter emissions, especially for the accumulation mode particles. Moreover, the performance in reducing nucleation mode particles is markedly better than that of accumulation mode ones, and this effect is greatly influenced by the engine operating conditions. At the beginning of DPF regeneration, the PN concentration increases sharply, especially the nucleation mode particles. After regeneration, the PN emissions decrease by two orders of magnitude. During regeneration, the particle size distribution exhibits a unimodal distribution, with the peak value increasing considerably and shifting toward smaller particle sizes. After regeneration, the particle size of the PN peak value slightly decreases and markedly shifts toward larger sizes, the accumulation mode particle concentration increases by 7.2 times, and the nucleation mode particle concentration increases by 2.6 times. Before the DPF regeneration, the axial temperature gradually decreases along the direction of the airflow, and the radial temperature gradually decreases from the center to the edge. During regeneration, the highest temperature occurs in the center of the DPF cross-section, whereas the temperature peak at the outlet interface occurs at the middle position of the DPF. The findings of this paper can provide scientific references to formulation and optimization of DPF regeneration strategies.

Filtration Efficiency and Regeneration Behavior in a Catalytic Diesel Particulate Filter with the Use of Diesel/Polyoxymethylene Dimethyl Ether Mixture

An Assessment of the Application of Catalyst Preheating Prior to Engine Cold Start to Improve the Filtration Performance of CDPF on Particulate Emissions

Particulate Matter Chemical Characteristics from a Light-Duty Diesel Engine Fueled with PODE/Diesel Blends

Energy Balance Analysis, Combustion Characteristics, and Particulate Number Concentration-No Trade-off of a Heavy-Duty Diesel Engine Fueled with Various PODEn/diesel Blends

Potential Improvement in Particulate Matter’s Emissions Reduction from Diesel Engine by Addition of PODE and Injection Parameters

Investigation on Combustion and Emission Characteristics of Diesel Polyoxymethylene Dimethyl Ethers Blend Fuels with Exhaust Gas Recirculation and Double Injection Strategy

Study of the Influence of Methanol/f-T Diesel Combustion Particle Materiality Parameters on the Deposition Process in Diesel Particulate Filter Trap Units

An experimental investigation of particulate emission characteristics of catalytic diesel particulate filters during passive regeneration

Study of the Particulate Purification Efficiency of Diesel Oxidation Catalyst and Catalyzed Diesel Particulate Filter

Oxidation Behaviors and Nanostructure of Particulate Matter Produced from a Diesel Engine Fueled with N-Pentanol and 2-Ethylhexyl Nitrate Additives

Particle filter performance of soot-loaded diesel particulate filter and the effect of its regeneration on the particle number and size distribution

Effects of Diesel/pode (polyoxymethylene Dimethyl Ethers) Blends on Combustion and Emission Characteristics in a Heavy Duty Diesel Engine

Development of a Reduced Polyoxymethylene Dimethyl Ethers (poden) Mechanism for Engine Applications

Research on the filtration and regeneration of fuel borne catalyst diesel particulate filter of diesel engine

Modeling of Soot Fragmentation That Proceeds in a Catalyzed Diesel Particulate Filter of a Diesel Engine

Effects of Porosity Setting and Multilayers of Diesel Particulate Filter on the Improvement of Regeneration Performance

A Research on the Filtration and Regeneration of Fuel Borne Catalyst Diesel Particulate Filter of Diesel Engine

Evaluation of Polyoxymethylene Dimethyl Ethers As a New Type of Diesel Additives

Effects of Biodiesel on Continuous Regeneration DPF Characteristics

Gaseous Emissions and Particle Microstructure Characteristics of PODE/Diesel Blend Fuel

Analysis of Temperature and Pressure Characteristics in Catalyzed Diesel Particulate Filter Operation for Heavy-Duty Diesel Engine