Abstract:The shear stress transport (SST) turbulence model and gamma-Re-theta transition model were employed when solving the Reynolds-averaged Navier-Stokes (RANS) equations. The flow separation in the suction side of the typical high-lift low-pressure gas turbine PakB blade was investigated. Different sets of mesh were adopted and the results of grid independence study show that the precision is maintained when the grid system of 126,780 is adopted. And the computational results were compared with the existing experimental and computational results, which indicate that the numerical method can predict the separated transition flow reliably. Different kinds of structures including V grooves and protrusions, curved grooves and protrusions, rectangular grooves and protrusions were used to passive control of the flow separation in the suction side of the PakB blade. The structures have the same locations including 65%C-ax, 68%C-ax and 71%C-ax on the suction side of the blade as well as length and height for better comparison. All of these cases are compared with the flow of PakB cascade without control with Re=86,000 and FSTI=1%. The shear layer is uplifted when the flow passes the passive device. And the separation bubble inside the grooves almost occupies the whole groove space which makes the length of the separation shorter than that in the case without control. The separation inside the grooves joins into the downstream separation in the case of grooves located in 71%C-ax. The flow starts to separate in the leeside of the protrusion wherever the protrusion locates. And the attachment point moves forward significantly in the comparison with the case of without control. However, it brings in more flow loss because of the protrusion's resistance to the boundary flow. In the total pressure loss coefficient comparison with the case without control, the grooves produce less flow loss while the protrusions at all the locations bring more flow loss. The nearer the groove is away from the separation point in the case without control, the higher the efficiency could be in the view of total pressure loss coefficient. The rectangular grooves are considered as a more effective structure for the flow separation control of PakB blade. Moreover, the flow separation bubble length and the total pressure loss coefficient decrease as Reynolds number increases in the cases without control. The total pressure loss coefficient in the different Reynolds numbers cases with rectangular groove is lower than that in the cases without control and the flow control performance gets much better when Reynolds number increases.

Control of bow shock induced three-dimensional separation using bleed through holes

Effects of Micro Blowing/suction Flow Control Devices on a NACA0015 Airfoil

Structure and Dynamics of Bleed-Controlled Impinging Shock/Turbulent-Boundary-Layer Interactions

Numerical Investigations of Shock/Boundary-Layer Interaction and Control for Mach 2.5 Flow in an Axisymmetric Inlet

Effect of perforated wall in controlling the separation due to SWBLI at Mach no. 5 to 9

Investigation on the three-dimensional shock wave/turbulence boundary layer control induced by the secondary recirculation jets

Wall pressure control of a 3D cavity with lateral apertures and wall proximity

Investigation of Corner Separation and Suction Control in Constant Area Duct

Numerical Investigation Of Flow Separation Control Of Low-Pressure High-Lift Blade With Different Grooves And Protrusions

Numerical study on the flow control mechanisms of an off-surface circular cylinder for wall-bounded flows with separation

Numerical Investigation of Steady Suction Control of Flow Around a Circular Cylinder

Unsteady control of supersonic turbulent cavity flow based on resolvent analysis

Suppression of flow separation around a finite wall-mounted square cylinder by suction at the side leading edge

Influences of microjet pressure and number of microjets on the control of shock wave/boundary layer interaction

Study of Flow Separation Control by Bleed Slot and Bleed Holes in a Transonic Compressor Cascade

On the distributed blowing control of flow around a square cylinder at a low Reynolds number

Study of the streamwise location of a micro vortex generator for a separation-control mechanism in supersonic flow

Numerical Investigation of Boundary Layer Separation Control on the Low-Pressure Turbine Blade by Oscillatory Blowing

Effects of Number of Bleed Holes on Shock-Wave/Boundary-Layer Interactions in a Transonic Compressor Stator

Mitigation of Shock-Induced Separation Using Square-Shaped Micro-Serrations—A Preliminary Study

A Study of Arc Plasma Energy Deposition Flow Control on Blunt-Headed Protuberance Induced STBLI