Abstract:Experiments are carried out on the Phi 2 m Shock Tunnel (FD-14A) at the China Aerodynamics Research and Development Center to study the effect of the transverse groove with/without discharge hole on the hypersonic blunt flat-plate boundary layer transition, and the preliminary computational and theoretical research are carried out. The inflow Mach number of the test is 6, the unit Reynolds number is 3.3 x 10(7)/m, the leading edge radius of the flat-plate is 1 mm, and the angle of attack is -4 degrees. Three different sets of two-dimensional transverse grooves are arranged at 110 mm away from the leading edge of the flat-plate. The width and depth of the grooves are, respectively, 2.5 mm and 1 mm for groove 1, 3.75 mm and 1.5 mm for groove 2, and 5 mm and 2 mm for groove 3, at the same time, both ends of the groove 1 can open the discharge hole (the discharge hole has a size of 2.5 mm x 5.0 mm and a width the same as that of groove 1). The discharge hole is denoted as the groove 4, and the smooth flat-plate when the groove is not included is denoted as groove 5 or the flat. The Phi 2-mm-diameter cylindrical heat flux sensor is used to measure the heat flux distributions of the center line of the flat-plate under different conditions, and thus we can judge the transition of the boundary layer. The measurement results show that the smooth plate starts to transit at x approximate to 340 mm, and the transition is nearly completed at x approximate to 425 mm. The groove causes the transition position of the boundary layer of the plate to advance, and as the width and depth of the groove increase, the promoting effect on the transition is enhanced, and the transition position moves upstream. After the groove 1 is added to the discharge hole (groove 4), the heat flux distribution and the transition position are substantially the same as those of the smooth plate. After the boundary layer flow completely transits into turbulent flow, the difference in heat flux for each case is small, which indicates that the grooves of different specifications affect only the heat flux distribution in the transition process, but have little effect on the heat flux of the turbulent wall after the transition. The computational fluid dynamic results show that the discharge holes cause passive suction, and the test results show that the suction effect of the discharge holes at both ends of the groove counteracts the effect of the groove on the transition of the center line boundary layer, but it may be just a coincidence, and further research is needed. The linear stability theory (LST) and the optimal perturbation method are used to analyze the flow instability mechanism of the smooth blunt plate. The LST results show that there is no first mode instability nor second mode instability in the blunt plate flow. The modal instability mechanism cannot explain the observed transition in the test. The optimal disturbance calculation shows that the blunt plate flow suffers strong non-modal instability, which can qualitatively explain the observed transition phenomenon.

A Study of Arc Plasma Energy Deposition Flow Control on Blunt-Headed Protuberance Induced STBLI

Flow Control Effect of Pulsed Arc Discharge Plasma Actuation on Impinging Shock Wave/boundary Layer Interaction

Response Characteristics of Impinging Shock Wave/turbulent Boundary Layer Interaction Disturbed by Arc Plasma Energy Deposition

Unsteadiness characterization of shock wave/turbulent boundary layer interaction controlled by high-frequency arc plasma energy deposition

Study on the Mechanism of Shock Wave and Boundary Layer Interaction Control Using High-Frequency Pulsed Arc Discharge Plasma

Shockwave-Boundary Layer Interaction Control by Plasma Aerodynamic Actuation: an Experimental Investigation

Shock Wave-Boundary Layer Interactions Control by Plasma Aerodynamic Actuation

Experimental study on the hypersonic double incident shock wave/boundary layer interaction regulated by plasma actuation array

Response of the Shock Wave/Boundary Layer Interaction to the Plasma Synthetic Jet

Swept Shock Wave/boundary Layer Interaction Control Based on Surface Arc Plasma

Experimental Investigation on Compression Ramp Shock Wave/boundary Layer Interaction Control Using Plasma Actuator Array

Shock wave and fully turbulent boundary layer interaction controlled by surface arc plasma actuation

Experimental study on effect of transverse groove with/without discharge hole on hypersonic blunt flat-plate boundary layer transition

Effects of plasma aerodynamic actuation on oblique shock wave in a cold supersonic flow

Experimental Investigation of Supersonic Boundary-Layer Tripping with a Spanwise Pulsed Spark Discharge Array

Experimental study on surface arc plasma actuation-based hypersonic boundary layer transition flow control

Experimental study on shock interaction control of double wedge in high-enthalpy hypersonic flow subject to plasma synthetic jet

Control of supersonic compression corner flow using a plasma actuator

On Mechanism of Plasma-Shock-Based Flow Control

Experimental Study of Arc Plasma Energy Deposition Flow Control on Supersonic Cavity Combustor

Effect of the Streamwise Pulsed Arc Discharge Array on Shock Wave/boundary Layer Interaction Control