Abstract:A promising high-strength Fe – 17.7Mn – 4.7Cr – 0.48C – 10Ni – 5Al – 4Cu wt.% Austenitic steel was solutionized, then aged for 3 or 10 h at 580°C producing a pronounced precipitation hardening response primarily due to the formation nanoscale NiAl precipitates. Density functional theory (DFT), molecular dynamics (MD), and discrete dislocation dynamics (DDD) calculations were combined with microstructural data from atom-probe tomography (APT), informing theoretical strengthening models to predict yield strength at different stages of precipitation as a function of NiAl size, volume fraction, and composition. These yield strength predictions were compared with experimental microhardness measurements of the various ageing conditions, including the peak microhardness of 490 HV, which corresponds to an estimated alloy yield strength of 1200 MPa. Comparing MD calculations with theoretical models showed that anti-phase boundary (APB) formation was the predominant barrier to dislocation motion posed by the NiAl precipitates. Using single dislocation particle strengthening models with NiAl APB energies calculated from DFT, good agreement was observed between DDD calculations and the 10 h peak-aged experimental measurements, while agreement with the 3 h experimental measurements required reducing the NiAl APB energy. These results demonstrate the utility of the undertaken approach integrating simulations and experiments across multiple length-scales, particularly the presented coarse-grained DDD simulation method towards modeling materials strengthened by very fine precipitates. The results further suggest that the observed NiAl precipitates may adopt an alternate crystal structure early in their formation.

A generalized line tension model for precipitate strengthening in metallic alloys

A statistical model for predicting the mechanical properties of nanostructured metals with bimodal grain size distribution

Dislocation dynamics prediction of the strength of Al-Cu alloys containing shearable $θ''$ precipitates

Multiscale modelling of precipitation hardening in Al-Cu alloys: dislocation dynamics simulations and experimental validation

Multiscale Modelling of Mechanical Response in a Martensitic Steel: A Micromechanical and Length-Scale-dependent Framework for Precipitate Hardening

A physically-based constitutive model for the prediction of yield strength in the precipitate-hardened high-entropy alloys

Predicting the Precipitation Hardening Response of Particle Strengthened Alloys Hardened by Ordered Precipitates

Dislocation Density-Based Model for Flow Behavior of a Near-α Titanium Alloy Considering Effects of Initial Lamellar Thickness

A Physically Based Mean Field Model for Strain‐Induced Precipitation and Recrystallization in High‐Strength Low‐Alloy Steels

A Coupled Model for Precipitation Strengthening in Mg-Zn Alloys

Modeling the effect of precipitation spatial geometry and size distribution on the yield strength of aluminum alloys

A general physics-based hardening law for single phase metals

Probability-Dependent Precipitation Strengthening Effect of Anisotropic Precipitate in Al-Mg-Si Alloy Produced by T6 Heat Treatment

Experimental and Modelling Assessment of Ductility in a Precipitation Hardening AlMgScZr Alloy

Dislocation storage-release-recovery model for metals under strain rates from 10−3 to 107 s−1, and application to tantalum

A Dislocation Density-Based Model for the Temperature Dependent Anomalous Behaviors of Nickel-Based Single-Crystal Superalloy

Microscopic Mechanisms and Continuous Models of Precipitation Hardening

Predicting Yield Stress in a Nano-Precipitate Strengthened Austenitic Steel by Integrating Multi Length-Scale Simulations and Experiments

Length-Scale-Dependent Micromechanical Modeling for Precipitate Hardening in Inconel 718 Superalloy

A Yield Stress and Work Hardening Model of Al-Mg-Si Alloy Considering the Strengthening Effect of β” and β’ Precipitates

A strain rate dependent thermo-elasto-plastic constitutive model for crystalline metallic materials