Abstract:A novel electromagnetic shocking treatment (EST) is put forward to reduce the stress corrosion cracking (SCC) susceptibility of high-strength aluminum alloys and its fasteners by selectively modifying grain boundary (GB) microstructure. The effect of EST on the microstructure, mechanical properties and SCC susceptibility of T73-Al7075 alloy and its high-lock nuts has been investigated. Mechanical properties, electrochemical performance and constant strain SCC test have been carried out for T73-Al7075 alloy, microhardness test and SCC test under wet-dry cyclic condition have been carried out for its high-lock nuts, as well as microstructure characterizations via SEM, EBSD and TEM have been carried out for T73-Al7075 alloy. Comparing to the received sample, the strength of EST sample basically keep consistent while the elongation increases slightly, besides, the electrical conductivity and electrochemical corrosion performance improves. The SCC susceptibility of T73-Al7075 alloy and its high-lock nuts have been reduced after EST. Microstructure characterization shows that the grain morphology and matrix intragranular precipitate distribution of the EST sample keep almost the same as those of the received sample, which is consistent with the almost unchanged mechanical properties of alloy sample. However, EST induces the transformation of grain boundary precipitates (GBPs) and the formation of stripy/wavy GB as observed experimentally, which indicates that EST promotes nonlinear GB wetting or pre-melting and even grain bridging. The phase transformation and GB complexion transition induced by EST are main factors attributing to the obvious improvement of SCC resistance of T73-Al7075 alloy and its high-lock nuts. It can be deduced that anodic dissolution cracking will be relieved because of the dissolution and coarsening of GBPs. Hydrogen induced cracking and crack propagation can be relieved with the occurrence of grain bridging. They are both beneficial to improve SCC resistance of Al7075 alloys. This work provides a novel EST method to targetedly embellish GB microstructure, optimize GB complexion and connectivity, and then enhance the service performance of solid alloys and even finished parts.

What problem does this paper attempt to address?

This paper aims to address the issue of stress corrosion cracking (SCC) in high-strength aluminum alloys (such as 7075 aluminum alloy) and their fasteners in stress corrosion environments. Specifically, the paper proposes a novel Electromagnetic Shocking Treatment (EST) method, which selectively alters the microstructure of Grain Boundaries (GB) to reduce the susceptibility of aluminum alloys and their fasteners to stress corrosion cracking. The study found that after EST treatment, the mechanical properties of the material remained largely unchanged, while its electrical conductivity and electrochemical corrosion resistance improved, significantly enhancing its resistance to stress corrosion cracking. Additionally, the EST treatment induced the transformation of Grain Boundary Precipitates (GBPs) and the formation of banded grain boundaries, thereby improving the service performance of the material.

Reducing stress corrosion cracking susceptibility of high-strength aluminum alloy and its fastener by a novel electromagnetic shocking treatment

A novel electromagnetic shock treatment to selectively modify grain boundary and improve the corrosion resistance of aluminium alloy

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

Gradient phase transformation of Al–Zn–Mg–Cu alloy induced by nonlinear interface wetting under electromagnetic shocking treatment

Achieving High-Strength Ductility Property in a Microstructure Homogenization Al-Zn-Mg-Cu Alloy by Electroshock Treatment

Investigating the impact and mechanisms of electromagnetic treatment on stress corrosion performance in 7075 aluminum alloy

Near-in-situ investigation of surface crack healing and strengthening mechanism of Ti-43.5Al-4Nb-1Mo-0.1B alloy by novel electroshock treatment

Investigation on the Effect of Electroshock Treatment on the Microstructure and Mechanical Properties of Ti-45Al-5Nb Alloy

Recrystallization Behavior of Ti–6.5Al–3.5Mo–1.5Zr–0.3Si Alloy under Electroshocking Treatment

Annealing Effect of High-Density Pulsed Electric Current Treatment on Cold-Rolled 6061 Aluminum Alloy

Realizing Strength–ductility Synergy in a Lean Duplex Stainless Steel Through Enhanced TRIP Effect Via Pulsed Electric Current Treatment

Evolution mechanism of grain orientation and texture distribution of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si alloy under electroshocking treatment

Effect of Stress-Aging Treatment on the Mechanical and Corrosion Properties of Al−Zn−Mg−Cu Alloy

Influence of Electroshocking Treatment on Microstructure and Mechanical Properties of Ti-6.5Al-3.5Mo-1.5Zr-0.3Si Thin-Wall Specimen Manufactured by Laser Melting Deposition

Influence mechanism of microstructure variation on mechanical properties of laser melting deposition Ti–6Al–4V alloy under electroshocking treatment

In-situ electrochemical analytical effect of aging treatment on stress corrosion behavior of Al–Zn–Mg–Cu aluminum alloy

Enhanced stress corrosion cracking resistance and electrical conductivity of a T761 treated Al-Zn-Mg-Cu alloy thin plate

Effect and Mechanism of Electroshock Treatment on Microstructure and Mechanical Properties of (Tib+tic)/ti-6Al-4v Composite

Synchronously enhancing the strength, toughness, and stress corrosion resistance of high-end aluminum alloys via interpretable machine learning

Microstructural Characterization and Mechanical Properties of 6061 Aluminum Alloy Processed with Short-Time Solid Solution and Aging Treatment

Optimizing strength and ductility in 7150 Al alloys via rapid electropulsing cyclic heat treatment