Abstract:Carbon nanotubes (CNTs) have outstanding characteristics including high mechanical properties, namely tensile strength and elastic modulus,and still remarkable flexibility, excellent thermal and electric conductivities, low percolation thresholds (loading weight at which a sharp drop in resistivity occurs) and high aspect ratios (length to diameter ratio, L/D) while the latter provides the nanotubes with additional advantage over spherical fillers to obtain high property composites. Therefore I CNTs have the potential to act as a reinforcing filler of polymer matrices. The tetraglycidyl-4,4'-diaminodiphenylmethane (TGDDM) cured with 4,4'-diaminodiphenylsulphone WDS) and filled with graphite or carbon fibers are commonly used as a polymeric matrix in high performance composites employed in the aircraft and spacecraft industries. In present paper, multi-walled carbon nanotubes (MWNTs) as a nano-filler were incorporated in the TGDDM/DDS epoxy. The thermal properties of the composites were studied by differential scanning calorimetry (DSC), dynamic thermal analysis (DMTA) and thermal gravitimetric analysis TGA). In addition, the dispersion of MWNTs in the epoxy was also investigated by scanning electron microscopy SEM). In DSC studies, Kissinger and Flynn-Wall-Ozawa (FWO) methods were used to study the nonisothermal cure kinetics of the MWNTs filled TGDDM/DDS composites at different heating rates. The activation energy (E.) of cure reactions of the MWNTs filled epoxy composites was obtained by Kissinger and FWO methods. For all composites, the E. obtained by Kissinger method was slightly less than that of FWO method. With the addition of MWNTs, the E. of the epoxy composites decreased first and then increased with the increase of the MWNTs contents. These results showed that the incorporation of carbon nanotubes accelerated the cure reaction of the TGDDM/DDS epoxy at lower MWNTs content due to the interaction between the hydroxyl groups on the surface of nanotubes and the epoxy. However, due to the high surface energy of carbon nanotubes, the viscosity of MWNTs/epoxy composites increased at higher MWNTs content. Hence, the mobility of hydroxyl groups was hindered, and the reaction energy of composites increased with increasing MWNTs contents. The influence of carbon nanotubes on the thermal stability of the epoxy was studied by TGA. It is shown that MWNTs had little influence on the thermal stability of the cured epoxy. The storage modulus and glass transition temperature of MWNTs filled TGDDM/DDS were investigated by DMTA. It is seen that the storage modulus of TGDDM/DDS system was enhanced with the increasing of MWNTs content, that is, the modulus increased 6.3% and 7.8% at 1 wt % and 5 % MWNTs content, respectively. The glass transition temperature of the epoxy slightly decreased. Furthermore, the DMTA results of MWNTs/TGDDM/DDS composites were compared with that of carbon narrofibers (CNFs)/TGDDM/DDS composites. It was shown that the interactions between CNFs and epoxy were better those between that MWNTs and epoxy. The dispersion of carbon nanotubes in the epoxy was studied by SEM. The SEM results suggest that of MWNTs had poor dispersion in the cured epoxy. However, the radii of carbon nanotubes in the epoxy were greater than those of pure nanotubes. These results show the existence of interaction between carbon nanotubes and epoxy.

Investigation of the influence of Halloysite Nanotubes (HNTs) on the low-velocity impact behavior of carbon fiber-reinforced epoxy composites

Reducing Dispersity of Mechanical Properties of Carbon Fiber/epoxy Composites by Introducing Multi-Walled Carbon Nanotubes

Study on transverse high-velocity impact resistance of carbon nanotube films and their based composites

Impact Properties of Multi-Wall Carbon Nanotubes Modified Composites

The Carbon Nanotubes Effect into Single-lap Joint Failure Modes and Load Capacity: a Macromechanical Analysis

Influence of Carbon Nanotube Coatings on Carbon Fiber by Ultrasonically Assisted Electrophoretic Deposition on Its Composite Interfacial Property.

Effects of Carbon Nanotubes on Thermal Behavior of Epoxy Resin Composites

The effect of carbon nanotubes loading and processing parameters on the electrical, mechanical, and viscoelastic properties of epoxy-based composites

Experimental investigation of the compressive behavior of epoxy nanocomposites reinforced with straight and helical carbon nanotubes

Effects of carbon nanotubes on open-hole carbon fiber reinforced polymer composites

Low-Velocity Impact Resistance and Compression After Impact Strength of Thermoplastic Nanofiber Toughened Carbon/Epoxy Composites with Different Layups

Thermoanalytical Studies of High Performance Epoxy/Carbon Nanotube Composites

Effects of the Electrophoretic Deposition of CNTs on the Mechanical Properties of Ti/CFRP Composite Laminates

Effectiveness of short and straight carbon nanotubes on dispersion state and static/dynamic mechanical properties of woven glass fibre-reinforced polymer laminates

Preparation and functional study of epoxy composites reinforced with ultra-low content single-walled carbon nanotubes

Effect of NH2-MWCNTs sprayed carbon fiber on the mechanical properties of carbon fiber reinforced polycarbonate composite for lightweight structural applications

Lap shear properties of CF/PEKK composites through nanoparticle-enhanced adhesive joints

Effectiveness of multi‐walled carbon nanotube on the improvement of tensile, flexural, and low‐velocity impact properties of hybrid Kevlar/carbon fiber reinforced epoxy‐based composites

A micromechanical study of the fatigue behavior of MWCNT-modified carbon fibers/epoxy resin single filament composites subjected to cyclic loadings

An experimental investigation of the effect of carbon nanotubes addition and shot peening process on the ballistic limit of fiber-metal laminates

Investigation of mechanical properties of multi-walled carbon nanotubes/hollow glass microspheres – carbon fibre-reinforced epoxy composites in transverse fibre directions