Abstract:Solenoid is an efficient element in the beam line to control the transverse rms emittance in normal conducting injectors. However, for the case of superconducting photoinjector the extra magnetic field can not exist in the area of SC cavity. By calcultaing and simulating, this paper presents the possibility of applying solenoid emittance compensation in the DC-SC photoinjector, a new type of superconducting gun developed at Peking University. INTRODUCTION Because the superconducting cavity can work in the CW mode and the photocathode is the best emitter with low emittance, the photo injectors based on superconducting cavity become the popular choice to produce the high average current electron beams for the high average power FELs and ERL. At Peking University, a new FEL facility (PKU-FEL) based on superconducting linac is on building, which is designed as high average power infrared (5~10μm) and THz (100~3000 μm) light source [1]. As the new electron source, DC-SC photoinjector has been developed in the last years. DC-SC photoinjector is a novel design different from the SC injectors in Rossendorf [2], BNL [3] and Jefferson lab [4]. By integrating a small DC Pierce gun with the superconducting cavity, it is free of the compatibility of the superconducting cavity and the normal conducting photocathode, which makes the production and operation easier compared with other designs. In 2004 the first beam loading has been successfully performed in the test facility of 1+1/2 cell DC-SC injector. Up to now, the gradient of 6 MV/m has been achieved at 4.4 K. The rms emittance about 5 mm-mrad has been measured in the beam test with the beam energy of 1.1 MeV and current of 270 μA [5]. In parallel to the prototype test of 1+1/2 cell gun, the simulation of the 2+1/2 cell photoinjector has been already done [6]. The goal of this new design is to produce the beams with the energy around 4 MeV, the bunch charge of 60~100 pC and the transverse emittance about 1 mm-mrad. For the idea of DC-SC photoinjector, the main open question was the relative large transverse emittance compared with the normal conducting RF gun. To further control the transverse rms emittance, the solenoid magnetic field compensation, which is an effective method in normal conducting gun, will be consided in the DC-SC injector case. 2+1/2 CELL GUN DESIGN In the design of 2+1/2 cell DC-SC injector, DC gun and superconducting cavity are the main parts. The geometry of the 2 full cells is based on the TESLA design; the first cell and the DC Pierce gun are optimized to provide good focusing to low energy electrons. The parameters of DC gun and the first cell are presented in figure 1 and table 1. The voltage applied on the cathode is -70 kV, and the maxmum field on the cathode surface is 6 MV/m. There exists a hole in the anode with the diameter of 8 mm through which the electrons enter the half cell cavity. To prevent the RF power loss caused by this hole, the distance between the anode of the Pierce gun and the wall of the half cell is designed to 13 mm. The first cell is optimized to a 0.6 cell with a slope wall of 5 degree, so that the RF field near the entrance of the cavity has the focusing force on the electrons. The electron field pattern can be found in [6]. In the dynamic simulation of this design without solenoid, the minimum normalized emittance is 3.4 mmmrad when the bunch charge is set as 100 pC. This result is much worse than the requirement, so the further control to greatly decrease the normalized emittance is necessary. Fig. 1: The geometric parameters of DC gun and the first cell (umit:mm) Table 1: The parameters of the new injector

Eliminating uncertainty of thermal emittance measurement in solenoid scans due to rf and solenoid fields overlap

Overestimation of Thermal Emittance in Solenoid Scans Due to Coupled Transverse Motion

Analysis of fringe field effects on measurement errors for Q-scanning-based emittance diagnosis system

Transverse Phase Space Tomography Using a Solenoid Applied to a Thermal Emittance Measurement

A method of bunch by bunch measurement at nanoseconds interval by using cavity beam position monitors

Possibility of adopting solenoid in dc-sc photoinjector

Single shot cathode transverse momentum imaging in high brightness photoinjectors

Thermal Emittance Isolation by Cathode Retraction

On emittance compensation solenoid of photoinjector using pulse current

Simulation Study on the Emittance Compensation of Off-Axis Emitted Beam in Rf Photoinjector

Thermal emittance measurements of a bi-alkali photocathode based on the high voltage DC photogun beamline

Rms emittance measures for solenoid transport and facility for rare isotope beams front-end simulations

Experimental Demonstration of the Correction of Coupled Transverse Dynamics Aberration in an Rf Photoinjector

Emittance Measurement ＆ Optimization for the Photocathode RF Gun with Laser Profile Shaping

Slice emittance measurement for photocathode RF gun with solenoid scanning and RF deflecting cavity

A New Measurement Of Electron Beam Emittance With Cerenkov Radiation "Double Imaging" Method

Rapid Thermal Emittance and Quantum Efficiency Mapping of a Cesium Telluride Cathode in an Rf Photoinjector Using Multiple Laser Beamlets

Effect of solenoid lens field on electron beam emittance

Experimental Investigation of Thermal Emittance Components of Copper Photocathode

On the Feasibility of Sub-100 Nm Rad Emittance Measurement in Plasma Accelerators Using Permanent Magnetic Quadrupoles

Analysis of Slice Transverse Emittance Evolution in a Very-High-frequency Gun Photoinjector